• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.577-579
• /
• 2004

Digital hearing aids enclose $6{\sim}8$ tiny components. Those electromechanical components are individually wired by soldering which is a manual labor and sometimes causes components' damage by heating. This paper suggests a PCB design for overcome these problems. Several PCBs are designed and manufactured and circuited to produce ITE(In The Ear) type hearing aids which are inserted in the ear canal. The most optimal size of the PCB design for the ITE hearing aid is presented in this paper.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1012-1015
• /
• 2004

Digital hearing aids enclose $6{\sim}8$ tiny components. Those electromechanical components are individually wired by soldering which is a manual labor and sometimes causes components' damage by heating. This paper suggests a PCB design for overcome these problems. Several PCBs are designed and manufactured and circuited to produce ITE(In-the-Ear) type hearing aids which are inserted in the ear canal. The most optimal size of the PCB design for the ITE hearing aid is presented in this paper.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.1044-1047
• /
• 2003

An acoustic testing device composed of 2 probe microphones was developed for the electro-acoustic specification testing of the ITE (In-The-Ear) hearing aid (HA). The amplitude ratio and the phase difference between the incident pressure onto the HA microphone and the outward pressure of the HA receiver were measured by the present acoustic system. The microphones were particularly used because of small acoustic cavities where input and output pressures were present. The acoustic wall composed of clay completely blocks the propagation of the sound pressure between the small acoustic cavities. The system has an advantage of structural flexibility for the acoustic testing of different sizes and shapes of ITE-type HAs.

• 한국전자파학회지:전자파기술
• /
• 제15권4호
• /
• pp.86-100
• /
• 2004

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 2004년도 추계학술발표대회논문집 제23권 2호
• /
• pp.235-238
• /
• 2004

대부분의 보청기 이용자들은 자신이 장애를 겪고 있다는 사실이 알려지는 것을 꺼린다. 따라서 보청기 사용자들은 귀 바깥쪽으로 들어 나지 않는 귓속형(ITE type) 보청기를 선호한다. 하지만, 이러한 귓속형 보청기를 제작하는 것은 쉬운 일이 아니다. 보청기의 각각 부품들만을 볼 때는 그 크기가 소형이지만, 부품 모두를 귀속에 넣는다고 한다면, 공간의 확보는 꼭 필요한 사항이다. 또한 보청기는 하나의 칩(chip)에 부품이 전선(wire)을 통해 납땜이 되는 구조이다. 이는 전선의 단락을 유발할 뿐만 아니라 칩과 전선이 쉽게 떨어지며, 잦은 납Eoa 작업으로 인해 열적으로 칩의 파손까지도 일으킨다. 이를 보안하고자 여기에서는 보청기 소형화 방법으로 PCB(Printed Circuit Board)를 제시하였다. PCB 를 사용함으로써 전선의 사용을 최소화하고, 부품과 PCB 와의 직접적인 결합으로 인해 보다 견고한 보청기 제작을 목표로 하였다. 아울러 PCB 를 통한 부품의 실장으로 기존의 수작업이던 보청기 제작을 자동화와 제작 시간의 단축이라는 이점을 얻을 수 있다.

• 한국소음진동공학회논문집
• /
• 제16권1호
• /
• pp.81-88
• /
• 2006

The most recent trend on digital hearing aid is to increase the ratio of signal to noise by directivity or to develop noise reduction algorithm inside DSP IC chip. This paper designed, fabricated and tested a digital hearing aid directivity testing device in which a micro-mouse-like the stepping motor with a speaker rotates around an examinant. Both ears of the examinant were fixed with ITE hearing aids in order to respond to receiving sound. The experimental results were compared with those of a boundary element method program for verification. The diameter of the directivity testing device was 2 m and the micro-mouse was precisely controlled by PICBASIC micro processor.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.469-474
• /
• 2005

The most recent trend on digital hearing aid is to increase the ratio of signal to noise by directivity or to develop noise reduction algorithm inside DSP IC chip. This paper designed, fabricated and tested a digital hearing aid directivity testing device in which a micro-mouse-1ike the stepping motor with a speaker rotates around an examinant. Both ears of the examinant were fixed with ITE hearing aids in order to response to receiving sound. The experimental results were compared with a boundary element method program for verification. The diameter of the directivity testing device was 2 [m] and the micro-mouse was precisely controlled by PICBASIC micro processor.

• 센서학회지
• /
• 제13권6호
• /
• pp.479-487
• /
• 2004

The prevention of noise induced hearing loss is very important, because there is no treatment for it. There are some kinds of devices for hearing protection, and those are effective in preventing a noise induced hearing loss. However, people often resist the use of hearing protection devices because it is difficult to have a conversation. Therefore, a hearing protection device is must effective not only in hearing protection but also in preserving communication ability. In this paper, we proposed a small acoustic filter for ITE type noise protector to solving the problem about the difficulties of conversation. That is applied a principle of acoustic filters that have been used for a muffler of automobiles, guns, and etc. To find out the sound transmission characteristic at the eardrum, we regarded an acoustic filter and external ear canal as a coupled system. So, we simulated the coupled system with OrCad, and experimented with a designed acoustic filter and a 2 cc coupler which has the same transmission characteristic as the external ear canal has. We confirmed that it is possible to adjustment acoustic transmission characteristics through simulation of electrical model for acoustic filter and external ear and experiments using designed small acoustic filters.

• 한국분무공학회지
• /
• 제24권1호
• /
• pp.35-42
• /
• 2019

Syngas is widely produced by incomplete combustion of coal, water vapor, and air (oxygen) in a high-temperature/high-pressure gasifier through a coal-gasification process for power generation. In this study, a simulation syngas which was mainly composed of $H_2$, CO, $CO_2$, and $N_2$ was fueled with diesel. A modified single cylinder compression ignition (CI) engine is equipped with intake port syngas supply system and mechanical diesel direct injection system for dual fuel combustion. Combustion and emission characteristics of the engine were investigated by applying various syngas composition ratios and compression ratios. Diesel fuel injection timing was optimized to increase indicated thermal efficiency (ITE) at the engine speed 1,800 rpm and part load net indicated mean effective pressure ($IMEP_{net}$) 2 to 5 bar. ITE of the engine increased with the $H_2$ concentration, compression ratio and engine load. With 45% of $H_2$ concentration, compression ratio 17.1 and $IMEP_{net}$ 5 bar, ITE of 41.5% was achieved, which is equivalent to that of only diesel fuel operation.

• 한국광학회지
• /
• 제11권5호
• /
• pp.317-322
• /
• 2000

본 논문에서는 두 파장 백색광 간섭법을 이용하여 금속물질을 단차 측정 시 발생하는 오차를 최소화하는 새로운 자가 보정법을 제안한다. 금속 물질의 파장에 대한 위상 변화율은 백색광 간섭무늬의 가시도 정점에 오차로 작용하는데, 자가 보정법은 위상 변화율을 일차 직선으로 가정하고 이를 추출하여 단차 값에 보상한다. 본 자가 보정법은 두 파장 백색광 간섭무늬가 갖는 두 개의 위상 정점과 한 개의 가시도 정점으로부터 위상 변화율 오차를 추출하므로, 별도의 실험이 필요하지 않다. 실험을 통하여 두 개의 금속 물질로 이루어진 단차를 $\pm2nm$ 이내의 오차로 측정함을 보인다.