• Membrane Journal
• /
• v.33 no.6
• /
• pp.352-361
• /
• 2023

Steam methane reforming is currently the most widely used technology for producing hydrogen, a clean fuel. Hydrogen produced by steam methane reforming contains impurities such as carbon monoxide, and it is essential to undergo an appropriate post-purification step for commercial usage, such as fuel cells. Recently, membrane separation technology has been gaining great attention as an effective purification method; in this study, we evaluated the feasibility of using commercial polysulfone membranes for biogas upgrading to separate and recover hydrogen from a hydrogen/carbon monoxide gas mixture. Initially, we examined the physicochemical properties of the commercial membrane used. We then conducted performance evaluations of the commercial membrane module under various conditions using mixed gas, considering factors such as stage-cut and operating pressure. Finally, based on the evaluation results, we carried out simulations for process design. The maximum H₂ permeability and H₂/CO separation factor for the commercial membrane process were recorded at 361 GPU and 20.6, respectively. Additionally, the CO removal efficiency reached up to 94%, and the produced hydrogen concentration achieved a maximum of 99.1%.

• Journal of Animal Environmental Science
• /
• v.16 no.3
• /
• pp.205-215
• /
• 2010

Geothermal heat pump system (GHPS) is an energy-efficient technology that use the relatively constant and renewable energy stored in the earth to provide heating and cooling. With the aim of using GHPS as a heating source, it's possibilities of application in farrowing house were examined by measuring environmental assessment and sow's performance. A total of 96 sows were assigned to 2 pig housings (GHPS and conventional housing) with 48 for four weeks in winter season. During the experimental period, indoor maximum temperature in GHPS-housing was measured up to $26.7^{\circ}C$, average temperature could maintain $21.2^{\circ}C$. The mean value of dust levels and $CO_2$, $NH_3$ and $H_2S$ gas emissions were decreased in GHPS-housing compare with those of conventional housing. Litter size, birth weight, parity and weaning weight did not differ between housings. However, feed intake of sow in GHPS-housing was lower than that of conventional housing. In energy consumption for heating, electric power consumption increased in GHPS-housing than the conventional housing, a 2,250 kwh increase, whereas there is no fuel usage for heater in GHPS-housing. Amount of ground water circulated for heating in cold weather for earth heat exchanger was 8.4-12.9 ton per day. In conclusion, GHPS may have environmental benefits and effectiveness of heating in farrowing housing and affect the performance in sows.

• Journal of Internet Computing and Services
• /
• v.16 no.1
• /
• pp.67-74
• /
• 2015

In recent years, frequent itemset mining for considering the importance of each item has been intensively studied as one of important issues in the data mining field. According to strategies utilizing the item importance, itemset mining approaches for discovering itemsets based on the item importance are classified as follows: weighted frequent itemset mining, frequent itemset mining using transactional weights, and utility itemset mining. In this paper, we perform empirical analysis with respect to frequent itemset mining algorithms based on transactional weights. The mining algorithms compute transactional weights by utilizing the weight for each item in large databases. In addition, these algorithms discover weighted frequent itemsets on the basis of the item frequency and weight of each transaction. Consequently, we can see the importance of a certain transaction through the database analysis because the weight for the transaction has higher value if it contains many items with high values. We not only analyze the advantages and disadvantages but also compare the performance of the most famous algorithms in the frequent itemset mining field based on the transactional weights. As a representative of the frequent itemset mining using transactional weights, WIS introduces the concept and strategies of transactional weights. In addition, there are various other state-of-the-art algorithms, WIT-FWIs, WIT-FWIs-MODIFY, and WIT-FWIs-DIFF, for extracting itemsets with the weight information. To efficiently conduct processes for mining weighted frequent itemsets, three algorithms use the special Lattice-like data structure, called WIT-tree. The algorithms do not need to an additional database scanning operation after the construction of WIT-tree is finished since each node of WIT-tree has item information such as item and transaction IDs. In particular, the traditional algorithms conduct a number of database scanning operations to mine weighted itemsets, whereas the algorithms based on WIT-tree solve the overhead problem that can occur in the mining processes by reading databases only one time. Additionally, the algorithms use the technique for generating each new itemset of length N+1 on the basis of two different itemsets of length N. To discover new weighted itemsets, WIT-FWIs performs the itemset combination processes by using the information of transactions that contain all the itemsets. WIT-FWIs-MODIFY has a unique feature decreasing operations for calculating the frequency of the new itemset. WIT-FWIs-DIFF utilizes a technique using the difference of two itemsets. To compare and analyze the performance of the algorithms in various environments, we use real datasets of two types (i.e., dense and sparse) in terms of the runtime and maximum memory usage. Moreover, a scalability test is conducted to evaluate the stability for each algorithm when the size of a database is changed. As a result, WIT-FWIs and WIT-FWIs-MODIFY show the best performance in the dense dataset, and in sparse dataset, WIT-FWI-DIFF has mining efficiency better than the other algorithms. Compared to the algorithms using WIT-tree, WIS based on the Apriori technique has the worst efficiency because it requires a large number of computations more than the others on average.

• Asia pacific journal of information systems
• /
• v.20 no.3
• /
• pp.191-204
• /
• 2010

Recently, the CO2 emission and energy consumption have become critical global issues to decide the future of nations. Especially, the spread of IT products and the increased use of internet and web applications result in the energy consumption and CO2 emission of IT industry though information technologies drive global economic growth. EU, the United States, Japan and other developed countries are using IT related environmental regulations such as WEEE(Waste Electrical and Electronic Equipment), RoHS(Restriction of the use of Certain Hazardous Substance), REACH(Registration, Evaluation, Authorization and Restriction of CHemicals) and EuP(Energy using Product), and have established systematic green business/IT strategies to enhance the competitiveness of IT industry. For example, the Japan government proposed the "Green IT initiative" for being compatible with economic growth and environmental protection. Not only energy saving technologies but energy saving systems have been developed for accomplishing sustainable development. Korea's CO2 emission and energy consumption continuously have grown at comparatively high rates. They are related to its industrial structure depending on high energy-consuming industries such as iron and steel Industry, automotive industry, shipbuilding industry, semiconductor industry, and so on. In particular, export proportion of IT manufacturing is quite high in Korea. For example, the global market share of the semiconductor such as DRAM was about 80% in 2008. Accordingly, Korea needs to establish a systematic strategy to respond to the global environmental regulations and to maintain competitiveness in the IT industry. However, green competitiveness of Korea ranked 11th among 15 major countries and R&D budget for green technology is not large enough to develop energy-saving technologies for infrastructure and value chain of low-carbon society though that grows at high rates. Moreover, there are no concrete action plans in Korea. This research aims to deduce the priorities of the Korean green business/IT strategies to use multi attribute weighted average method. We selected a panel of 19 experts who work at the green business related firms such as HP, IBM, Fujitsu and so on, and selected six assessment indices such as the urgency of the technology development, the technology gap between Korea and the developed countries, the effect of import substitution, the spillover effect of technology, the market growth, and the export potential of the package or stand-alone products by existing literature review. We submitted questionnaires at approximately weekly intervals to them for priorities of the green business/IT strategies. The strategies broadly classify as follows. The first strategy which consists of the green business/IT policy and standardization, process and performance management and IT industry and legislative alignment relates to government's role in the green economy. The second strategy relates to IT to support environment sustainability such as the travel and ways of working management, printer output and recycling, intelligent building, printer rationalization and collaboration and connectivity. The last strategy relates to green IT systems, services and usage such as the data center consolidation and energy management, hardware recycle decommission, server and storage virtualization, device power management, and service supplier management. All the questionnaires were assessed via a five-point Likert scale ranging from "very little" to "very large." Our findings show that the IT to support environment sustainability is prior to the other strategies. In detail, the green business /IT policy and standardization is the most important in the government's role. The strategies of intelligent building and the travel and ways of working management are prior to the others for supporting environment sustainability. Finally, the strategies for the data center consolidation and energy management and server and storage virtualization have the huge influence for green IT systems, services and usage This research results the following implications. The amount of energy consumption and CO2 emissions of IT equipment including electrical business equipment will need to be clearly indicated in order to manage the effect of green business/IT strategy. And it is necessary to develop tools that measure the performance of green business/IT by each step. Additionally, intelligent building could grow up in energy-saving, growth of low carbon and related industries together. It is necessary to expand the affect of virtualization though adjusting and controlling the relationship between the management teams.

• Asia pacific journal of information systems
• /
• v.19 no.3
• /
• pp.125-150
• /
• 2009

RFID(Radio Frequency IDentification) is a wireless frequency of recognition technology that can be used to recognize, trace, and identify people, things, and animals using radio frequency(RF). RFID will bring about many changes in manufacturing and distributions, among other areas. In accordance with the increasing importance of RFID techniques, great advancement has been made in RFID studies. Initially, the RFID research started as a research literature or case study. Recently, empirical research has floated on the surface for announcement. But most of the existing researches on RFID adoption have been restricted to a dichotomous measure of 'adoption vs. non-adoption' or adoption intention. In short, RFID research is still at an initial stage, mainly focusing on the research of the RFID performance, integration, and its usage has been considered dismissive. The purpose of this study is to investigate which factors are important for the RFID adoption and implementation with organizational resources. In this study, the organizational resources are classified into either finance resources or IT knowledge resources. A research model and four hypotheses are set up to identify the relationships among these variables based on the investigations of such theories as technological innovations, adoption stage, and organizational resources. In order to conduct this study, a survey was carried out from September 27, 2008 until October 23, 2008. The questionnaire was completed by 143 managers and workers from physical distribution and manufacturing companies related to the RFID in South Korea. 37 out of 180 surveys, which turned out unfit for the study, were discarded and the remaining 143(adoption stage 89, implementation stage 54) were used for the empirical study. The statistics were analyzed using Excel 2003 and SPSS 12.0. The results of the analysis are as follows. First, the adoption stage shows that perceived benefits, standardization, perceived cost savings, environmental uncertainty, and pressures from rival firms have significant effects on the intent of the RFID adoption. Further, the implementation stage shows that perceived benefits, standardization, environmental uncertainty, pressures from rival firms, inter-organizational cooperation, and inter-organizational trust have significant effects on the extent of the RFID use. In contrast, inter-organizational cooperation and inter-organizational trust did not show much impact on the intent of RFID adoption while perceived cost savings did not significantly affect the extent of RFID use. Second, in the adoption stage, financial issues had adverse effect on both inter-organizational cooperation and the intent against the RFID adoption. IT knowledge resources also had a deterring effect on both perceived cost savings and the extent of the RFID adoption. Third, in the implementation stage, finance resources had a moderate effect on environmental uncertainty and extent of RFID use while IT knowledge resources had also a moderate effect on perceived cost savings and the extent of the RFID use. Limitations and future research issues can be summarized as follows. First, it is difficult to say that the sample is large enough to be representative of the population. Second, because the sample of this study was conducted among manufacturers only, it may be limited in analyzing fully the effect on the industry as a whole. Third, in consideration of the fact that the organizational resources in the RFID study require a great deal of researches, this research may deem insufficient to fulfill the purpose that it initially set out to achieve. Future studies using performance research are, therefore, needed to help better understand the organizational level of the RFID adoption and implementation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.1
• /
• pp.58-68
• /
• 2010

In this paper, we propose an efficient link protection switching scheme for provider backbone bridge systems with a spanning tree for backup links exclusively, and evaluate its performance. The proposed scheme offers guaranteed QoS flows even when a link fault occurrs in the primary link by flooding the flows over the profiled spanning tree. The flooding mechanism over the spanning tree can also provide low latency and remove the loopback flows. We also derive the efficiency of bandwidth usage for the normal flows and the number of lost frames during the link restoration. For evaluating its feasibility, we implement a prototype of PBB-TE systems based on the Linux bridge codes, which can support both link protection switching capability with CCM and MAC-in-MAC encapsulation. A related protocol analyzer is also developed. One can see that the proposed scheme and the prototype can be useful for developing carrier class Ethernet systems based on PBB-TE.

• Journal of KIISE
• /
• v.44 no.9
• /
• pp.932-945
• /
• 2017

In this paper, a new hardware and software architecture for a stereo vision processing system including rectification, disparity estimation, and visualization was developed. The developed method, named LArge scale stereo matching method using Support Point Interpolation (LASPI), shows excellence in real-time processing for obtaining dense disparity maps from high quality image regions that contain high density support points. In the real-time processing of high definition (HD) images, LASPI does not degrade the quality level of disparity maps compared to existing stereo-matching methods such as Efficient LArge-scale Stereo matching (ELAS). LASPI has been designed to meet a high frame-rate, accurate distance resolution performance, and a low resource usage even in a limited resource environment. These characteristics enable LASPI to be deployed to safety-critical applications such as an obstacle recognition system and distance detection system for autonomous vehicles. A Field Programmable Gate Array (FPGA) for the LASPI algorithm has been implemented in order to support parallel processing and 4-stage pipelining. From various experiments, it was verified that the developed FPGA system (Xilinx Virtex-7 FPGA, 148.5MHz Clock) is capable of processing 30 HD ($1280{\times}720pixels$) frames per second in real-time while it generates disparity maps that are applicable to real vehicles.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.2
• /
• pp.25-30
• /
• 2018

Sn-Pb solder has been used in automotive electronics for decades. However, recently, due to the environmental and health concerns, some international environmental organizations such as the end-of-life vehicle (ELV) enacted legislation banning of the Pb usage in automotive electronics. For this reason, many studies to develop and promote Pb-free soldering have been significantly reported. Meanwhile, because of flexibility and lightweight, flexible printed circuit boards (FPCBs) have been increasingly used in automotive electronics for lightweight to improve fuel efficiency and space utilization. Although the properties of lead-free solders for automotive electronics have been widely studied, there is a lack of research on the reliability performance of the lead-free solder joint on FPCB under user conditions. This study reported the properties of solder joints between Pb-free solders such as Sn3.0Ag0.5Cu, Sn0.7Cu and Sn0.5Cu0.01Al (Si), and various FPCBs finished with organic solderability preservative (OSP) and electroless nickel immersion gold (ENIG). To evaluate on joint properties and reliabilities with different solder compositions and surface-finishing materials, pull strength test, thermal shock test, and bending cycle test were performed and analyzed. After the bending cycle test of solder joint on OSP-finishing, the fractures were occurred in solder and the lifetime of Sn3.0Ag0.5Cu solder joint was the longest.

• Journal of the Korea Concrete Institute
• /
• v.23 no.4
• /
• pp.511-520
• /
• 2011

Recent studies to improve reinforcement of structures have developed stiff type Polyurea by using highly polymized compound Polyurea, but the reinforcing effect of it appears to be merely good. To find the proper usage of Polyurea as structural reinforcement, stiff type Polyurea has developed by manipulating the ratio of the components that consist flexural type Polyurea and the developed stiff type Polyurea shows higher hardness and tensile capacity. The reinforcement effect evaluation of has been performed by the polyurea applied RC slab specimens, and the reinforcement effect of the combination of fiber sheet and polyurea has been tested. The results shows that the Polyurea applied specimens have significant improvement on hardness and ductility compare to those of unreinforced. Also, the specimens that stiff type Polyurea is sprayed on fiber sheet reinforcement has higher reinforcing effect than only sheet reinforced specimens. However, the specimens that and fiber sheet attached after polyurea applied on showed that the high toughness of fiber sheet restrains the ductile behavior of Polyurea due to the high ductility, thereby the specimen suffers the concentration of load, which leads the brittle fracture behavior.

• Science of Emotion and Sensibility
• /
• v.23 no.3
• /
• pp.37-46
• /
• 2020

This study was aimed at investigating the activities of a badminton club and designing smart wear to prevent sports injuries during badminton club activities. Everyone is familiar with sports in an aging society and clubs are gradually developing. Popular badminton club activities lead to frequent sports injuries, especially ankle injuries, which are a serious problem that hampers members' participation in sports. Therefore, this study aims to propose a prototype design for smart wear to prevent sports injuries, including ankle injuries. First, we identified the characteristics and considerations of members of badminton clubs, and the components of smart wear to prevent sports injuries. Second, members of the badminton clubs and an elite badminton player participated in a survey on the issues and requirements associated with wearing smart wear. Third, usage scenarios for smart wear were created based on literature reviews and the user assessment lists. Fourth, a prototype of the smart wear to prevent sports injuries including ankle injuries was created based on the scenarios. With the proposed smart wear, members of badminton clubs who may require assistance with sports injuries will be able to monitor said injuries, as well as their health condition, as avatars in visual games through a smart terminal. The visual game system will provide easier access to information about sports injuries and health. This smart sportswear will allow members of badminton clubs to prevent sports injuries and review their performance. This study can be utilized to design smart wear to prevent sports injuries and monitor sporting activities or bio-signals.