• Journal of Power Electronics
• /
• 제19권5호
• /
• pp.1087-1098
• /
• 2019

In this paper, a detuning factor (DeFac) method is proposed to design the key parameters for optimizing the transfer power and efficiency of an Inductively Coupled Power Transfer (ICPT) system with primary-secondary side compensation. Depending on the robustness of the system, the DeFac method can guarantee the stability of the transfer power and efficiency of an ICPT system within a certain range of resistive-capacitive or resistive-inductive loads. A MATLAB-Simulink model of a ICPT system was built to assess the system's main evaluation criteria, namely its maximum power ratio (PR) and efficiency, in terms of different approaches. In addition, a magnetic field simulation model was built using Ansoft to specify the leakage flux and current density. Simulation results show that both the maximum PR and efficiency of the ICPT system can reach almost 70% despite the severe detuning imposed by the DeFac method. The system also exhibited low levels of leakage flux and a high current density. Experimental results confirmed the validity and feasibility of an ICPT system using DeFac-designed parameters.

• Journal of Electrical Engineering and Technology
• /
• 제13권6호
• /
• pp.2178-2186
• /
• 2018

Online identification of load parameters is the premise of establishing a stable and highly-efficient ICPT (Inductive Coupled Power Transfer) system. However, compared with pure resistive load, precise identification of composite load, such as resistor-inductance load and resistance-capacitance load, is more difficult. This paper proposes a method for detecting the composite load parameters of ICPT system utilizing harmonics. In this system, the fundamental and harmonic wave channel are connected to the high frequency inverter jointly. The load parameter values can be obtained by setting the load equation based on the induced voltage of secondary-side network, the fundamental wave current, as well as the third harmonic current effective value received by the secondary-side current via Fourier decomposition. This method can achieve precise identification of all kinds of load types without interfering the normal energy transmission and it can not only increase the output power, but also obtain higher efficiency compared with the fundamental wave channel alone. The experimental results with the full-bridge LCCL-S type voltage-fed ICPT system have shown that this method is accurate and reliable.

• Journal of Power Electronics
• /
• 제19권3호
• /
• pp.655-664
• /
• 2019

In order to analyze the nonlinear phenomena of the bifurcation and chaos caused by the switching of nonlinear switching devices in inductively coupled power transfer (ICPT) systems, a Jacobian matrix model, based on discrete mapping numerical modeling, is established to judge the system stability of the periodic closed orbit and to study the nonlinear behavior of Hopf bifurcation in a system under full resonance. The general flow of the parameter design, based on the stability principle for ICPT systems, is proposed to avoid the chaos and bifurcation phenomena caused by unreasonable parameter selection. Firstly, based on the state equation of SS-type compensation, a three-dimensional bifurcation diagram with the coupling coefficient as the bifurcation parameter is established with a numerical simulation to observe the nonlinear phenomena in the system. Then Filippov's method based on a Jacobian matrix model is adopted to deduce the boundary of stable operation and to judge the type of the bifurcation in the system. Then the general flow of the parameter design based on the stability principle for ICPT systems is proposed through the above analysis to realize stable operation under the conditions of weak coupling. Finally, an experimental platform is built to confirm the correctness of the numerical simulation and modeling.

• Journal of Power Electronics
• /
• 제15권6호
• /
• pp.1654-1663
• /
• 2015

Compared to LC resonance, LCL resonance has distinct advantages such as a large resonant capability, low voltage and current stresses of the power device, constant voltage or current output characteristics, and fault-tolerance capability. Thus, LCL resonant compensation is employed for a movable Inductive Contactless Power Transfer (ICPT) system with a multi-load in this paper, which achieves constant current output characteristics. Peculiarly, the primary side adopts a much larger compensation inductor than the primary leakage inductor to lower the reactive power, reduce the input current ripple, generate a large current in the primary side, and realize soft-switching. Furthermore, this paper proposes an approximate resonant point for large inductor-ratio LCL resonant compensation through fundamental wave analysis. In addition, the PWM control strategy is used for this system to achieve constant current output characteristics. Finally, an experimental platform is built, whose secondary E-Type coils can ride and move on a primary rail. Simulations and experiments are conducted to verify the effectiveness and accuracy of both the theory and the design method.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제7권2호
• /
• pp.405-424
• /
• 2013

In publishing applications, it is advantageous to embed data in halftone images. The CPT scheme (Chen-Pan-Tseng, 2000) is a steganographic data hiding scheme that was proposed for binary images, e.g., facsimiles. The CPT scheme uses a secret key and weight matrix to protect the hidden data and can hide as many as $r={\lfloor}{\log}_2(m{\times}n+1){\rfloor}$ bits of data in the image by changing at most 2 bits in the image. Our proposed scheme also uses a secret key to protect it from being compromised and a weight matrix to increase the data hiding rate. Our scheme improves the performance of the CPT scheme by using the simple principle of splitting each block into two parts. Our proposed scheme is called improved CPT (ICPT) and has a very high embedding capacity compared to previous schemes. Experimental results demonstrate that our proposed scheme generally has higher performance than previous schemes.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권3호
• /
• pp.349-355
• /
• 2013

This paper presents the multi-objective optimisation of an Inductive Coupled Power Transfer (ICPT) device. A setup as complicated as the one at hand in this paper is extremely hard to model analytically. To acquire some knowledge about the influence of the geometric factors, a sensitivity analysis is first performed using design of experiment (DoE) and finite-element modelling (FEM). It allows validating that the choice of the free factors is relevant. This being done, the optimisation itself is performed using a genetic algorithm (GA), with two objectives and a strict functioning constraint.