• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1603-1610
• /
• 2013

The high distribution costs causes the increasing of truck delivery time and cost, which results in reducing industrial competitiveness incre. Therefore, This study conducted research into the introduction of truck only lane for reducting distribution costs. The site of study is Keumho JCT ~ Namgumi IC of Kyeongbu Expressway which has much truck traffic because of industrial complex. Thus, this study deduced travel speed and density in each scenaria(base, bus only lane, truck only lane, two only lane). According to analysis result, if a truck only lane install, the average driving speed is 83.4km/h as a highest and density 22.47veh/km as lowest. it means that if the truck only lane is install, it will be positive influence on the expressway

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.767-773
• /
• 2018

This paper proposes the simple structure LED-driving power converter with high power factor. As the proposed power converter combines the PFC boost converter and the conventional flyback converter into only one power conversion circuit, it simplifies the structure of LED-driving power converter. Thus the proposed converter is controlled using only one PWM controller IC, and it achieves high power factor, constant output voltage/current and cost-effectiveness. Therefore the proposed converter is suitable for the industry production and utilization of LED-light-system. In this paper, the operation analysis and design example of the proposed converter are explained, briefly. Also experimental results of the prototype that is implemented based on the designed circuit parameters are shown to validate operation characteristics of the proposed converter.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.745-748
• /
• 2003

This paper presents a study on pull cord switch system which is employed in various industry for emergency stop of the equipments. By using power line communication(PLC) technique, in this paper, a new method for operation position detection of pull cord switch is suggested without complicated wiring of separate cables which utilize only 2 lines. Also, using control function of PLC IC, a reset signal for each switch reset can be implemented in the switch status control/sensing device. Finally, this paper shows validity and practical applicability of the proposed operating position sensing system of pull cord switch by implementing the system and revealing the response time and signal through the PLC line.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.1
• /
• pp.152-159
• /
• 2010

High power density and power conversion efficiency have been required in the power converters according to the rapid growth of industry. In this context, the next generation High Speed Train(HST) requires power converter which has high-efficiency, high-performance and high-density. In this paper, the new control technique for battery charger used for the next generation HST is proposed. The phase shift ZVZCS converter is classified according to a resonant circuit which is located in the primary or secondary side. In this paper, The PWM switching technique using all-pass filter is proposed to control ZVZCS converter which has resonant circuit in the secondary side. ATmega_128 micro controller based in all-pass filter in substitute for phase shift IC is presented to have digital control. To verify the proposed topology, the simulation and experiment are performed by using PSIM software and 1[kW] experimental set-up.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.7 no.2
• /
• pp.223-232
• /
• 1997

The accuracy and precision of a modified method of NIOSH Method 7600 and EPA method 218.6 was determined for analyzing hexavalent chromium, Cr(VI), collected on PVC filter from workplace air. The method was designed to extract from Cr(VI) on PVC filter with a alkali solution, 2% NaOH/3% $Na_2CO_3$, and to analyze it using ion chromatography/visible absorbance detection(IC/VAD). The results and conclusion are as the following. 1. The peak of Cr(VI) was separated sharply on chromatogram and was linearly related with Cr(VI) concentration in sloution. The correlation coefficient was 0.9999 in a calibration curve. The limit of detection was 0.25 $0.25{\mu}g/sample$. 2. The accuracy(% recovery) was 93.3% in a set of sample($9-50{\mu}g$) stored for a day, and 100.1%($10-60{\mu}g$) in another set of samples stored for 2 hours. It is assumed that the difference in recovery by storage time was due to reduction of Cr(VI) to Cr(III). 3. The precision(coefficient of variation, CV) of the method was 0.015 in spiked samples with Cr(VI) standard solution, and 0.010 in spiked samples with plating solution from a chrome electroplating factory. The overall CV in all types of samples was 0.0013. 4. The Cr(VI) was stable in 2% NaOH/3% $Na_2CO_3$ at least for 10 hours. In conclusion, the IC/VAD method is appropriate for determining low-level Cr(VI) in workplace air containing various interferences.

• Journal of Korea Society of Industrial Information Systems
• /
• v.18 no.3
• /
• pp.1-8
• /
• 2013

Plasma display panel (PDP) televisions are facing to have a new chance to receive attention along with a boom in 3-D software and contents because PDP can provide the comfortable and realistic 3-D images. The PDP has three driving circuit boards such as X, Y and addressing boards. Cost effective driving waveform has already been reported to decrease the number of driving circuit board. Half bridge based sustaining driver can remove a sustaining driver in the X board. However, the biasing circuit in the X driving boards cannot be reduced because there are some drawbacks such as unstable gas discharge condition and unreliability of an address driver IC. In this paper, the half bridge based sustaining driver is considered and a simple address driver is proposed to remove one driving board, X driving board. The stable gas discharge condition, reliability of the address driver IC and the low cost can be obtained by the proposed circuit.

• Journal of the Korea Computer Industry Society
• /
• v.3 no.3
• /
• pp.369-382
• /
• 2002

The increase of vehicles stagnations leads to the increasing attention to the way customers pay and a large number of Projects on electronic cash system. Tranport system is comprised of a number of advanced technologies, including information processing, communications, control, and electronics. Recently many research on a system which provides contact in order to protect driver's vehicle passage have been carried out. And some potential problems from that system are being reviewed by electronic cash system. In this papers, we suggest RF protocol developing technology using the concept of electronic cash. ATM electronic cash developing is consist of component of pre-developed coin throw, integration of component using its, and production of more requirement-satisfactory ITS solution. Result increase 15-40% pre-type vehicles stagnations. Especially, we expect this proposed concept would be well adapted to our national environments.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.11 no.4
• /
• pp.1-12
• /
• 2015

This research analyzes the current state of the semiconductor industry delivering the prediction for the future development of the semiconductor industry along with some semiconductor memory's responsive strategies. In the 2014, top 10 semiconductor companies were targeted and studied its growth based on its profitability and growth indications in perspective during three years. The system semiconductor industry with the increase in Hyper-scale customers, proactive actions in the technology consortium, is polarizing caused by increased R&D expense to ensure process scaling limits and high performance, and some results have shown: PC and Mobile slowdown and growth recession phenomenon due to IoT's unclear direction. The leading company is to secure new growth engines through 'Acquiring'. While as the subordinated companies following this consecutive survival through the 'Acquired', the future of system semiconductor industry is to strengthen the market dominance and its techniques by concentrating on the reorganization of the market by few large companies. Accordingly, the semiconductor memory industry is expected to reach the limit of its expansion to domain of system semiconductor, and it is highly suggesting the need of the 'Memory Life Extension' growth strategy.

• Journal of Industrial Technology
• /
• v.22 no.A
• /
• pp.37-42
• /
• 2002

The shearing process for the sheet metal is normally used in the precision elements such as a frame of TFT-LCD or lead frame of IC chips. In these precision elements, the burr formation prevents the system assembly and needs the additional burr removing process. In this study, we have developed the novel ultrasonic deburring system to remove the small burr came from shearing of the sheet metal effectively. The deburring tool is driven by the stepping motor and alumina and SiC particles are used as abrasives. Ultrasonic power and the flowing resistance of the abrasives make ti possible to abrasive the burr.

• Journal of Korea Society of Industrial Information Systems
• /
• v.12 no.2
• /
• pp.79-84
• /
• 2007

This papar reports design and fabrication of CMOS temperature control circuit using MOSIS 0.25um-3.3V CMOS technology. The proposed circuit has a temperature coefficient of $13mV/^{\circ}C$ for a wide operating temperature range with a good linearity. Furthermore, the temperature coefficient of output voltage can be controlled by adjusting external bias voltage. This circuit my be applicable to the design of one-chip IC where quartz crystal resonator is mounted on CMOS oscillator chips.