• Membrane and Water Treatment
• /
• v.12 no.1
• /
• pp.43-49
• /
• 2021

The Commercial polymeric membranes like Polysulfone (PSF), Polyvinylidene difluoride (PVDF) and Polyacrylonitrile (PAN) which are an integral part of water purification investigation were chosen for the shockwave (SW) exposure experiment. These membranes were prepared by blending polymer (wt. %) / DMF (solvent) followed by phase-inversion casting technique. Shockwaves are generated by using Reddy Tube lab module (Table-top Shocktube) with range of pressure (1.5, 2.5 and 5 bar). Understanding the changes in membrane before and after shock wave treatment by parameters, i.e., pure water flux (PWF), rejection (%), porosity, surface roughness (AFM), morphology (SEM) and contact angle which can significantly affect the membrane's performance. Flux values PSf membranes shows increase, 465 (pristine) to 524 (1.5wt%) LMH at 50 Psi pressure and similar enhancement was observed at 100Psi (625 to 696 LMH). Porosity also shows improvement from 73.6% to 76.84% for 15wt% PSf membranes. It was observed that membranes made of polymers such as PAN and PSF (of high w/w %) exhibits some resistance against shockwaves impact and are stable compared to other membranes. Shockwave pressure of up to 1.5 bar was sufficient enough to change properties which are crucial for performance. Membranes exposed to a maximum pressure of 5 bar completely scratched the surface and with minimum pressure of 1.5bar is optimum enough to improve the water flux and other parameters. Initial results proved that SW may be suitable alternative route to minimize/control membrane fouling and improve efficiency.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.06a
• /
• pp.72-72
• /
• 2001

Plasma polymerized thin films have been deposited on Si(lOO) substrates at $25-400^{\circ}C$ using thiophene ($C_4H_4S$) precursor by plasma assisted chemical vapor deposition (PACVD) method for low-dielectric device application. In order to compare physical properties of the as-grown thin films, the effects of the plasma power, gas flow ratio and deposition temperature on the dielectric constant and thermal stability were mainly studied. XRD and TED studies revealed that the as-grown thin films have highly oriented amorphous polymer structure. XPS data showed that the polymerized thin films that grown under different RF power and deposition temperature as well as different gas ratio of $Ar:H_2$ have different stoichiometric ratio of C and S compared with that of monomer, indicating a formation of mixture polymers. Moreover, we also realized that oxygen free and thermally stable polymer thin films could be grown at even $400^{\circ}C$. The results of SEM, AFM and TEM showed that the polymer films with smooth surface and sharp interface could be grown under various deposition conditions. From the electrical property measurements such as I-V and C-V characteristics, the minimum dielectric constant and the best leakage current were obtained to be about 3.22 and $10-11{\;}A/\textrm{cm}^2$, respectively.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.533-537
• /
• 2003

Compared to sintered polycrystalline diamond (PCD), the deposited thin film diamond has a great advantage on the fabrication of cutting tools with complex geometries such as drills. Because of high performance in high speed machining non-ferrous difficult-to-cut materials in the field of automobiles industry, aeronautics and astronautics industry, diamond-coated drills find large potentialities in commercial applications. However, the poor adhesion of the diamond film on the substrate and high surface roughness of the drill flute adversely affect the tool lift and machining quality and they become the main technical barriers for the successful development and commercialization of diamond-coated drills. In this paper, diamond thin films were deposited on the commercial WC-Co based drills by the electron aided hot filament chemical vapor deposition (EACVD). A new multiple coating technology based on changing gas pressure in different process stages was developed. The large triangular faceted diamond grains may have great contribution to the adhesive strength between the film and the substrate, and the overlapping ball like blocks consisted of nanometer sized diamond crystals may contribute much to the very low roughness of diamond film. Adhesive strength and quality of diamond film were evaluated by scanning electron microscope (SEM), atomic force microscope (AFM), Raman spectrum and drilling experiments. The ring-block tribological experiments were also conducted and the results revealed that the friction coefficient increased with the surface roughness of the diamond film. From a practical viewpoint, the cutting performances of diamond-coated drills were studied by drilling the SiC particles reinforced aluminum-matrix composite. The good adhesive strength and low surface roughness of flute were proved to be beneficial to the good chip evacuation and the decrease of thrust and consequently led to a prolonged tool lift and an improved machining quality. The wear mechanism of diamond-coated drills is the abrasive mechanical attrition.

• New Physics: Sae Mulli
• /
• v.68 no.12
• /
• pp.1281-1287
• /
• 2018

In this study, $Al_xGa_{1-x}N$ films were grown on (0001) sapphire substrates by using metal-organic chemical vapor deposition (MOCVD). The crystallinity of the grown films was examined with X-ray diffraction (XRD) patterns. The surfaces and the chemical properties of the $Al_xGa_{1-x}N$ films were investigated using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS), respectively. The optical properties of the $Al_xGa_{1-x}N$ film were studied in a wide photon energy range between 2.0 ~ 8.7 eV by using spectroscopic ellipsometry (SE) at room temperature. The data obtained by using SE were analyzed to find the critical points of the pseudodielectric function spectra, $<{\varepsilon}(E)>=<{\varepsilon}_1(E)>+i<{\varepsilon}_2(E)>$. In addition, the second derivative spectra, $d^2<{\varepsilon}(E)>/dE^2$, of the pseudodielectric function for the $Al_xGa_{1-x}N$ films were numerically calculated to determine the critical points (CPs), such as the $E_0$, $E_1$, and $E_2$ structure. For the four samples (x = 0.18, 0.21, 0.25, 0.29) between a composition of x = 0.18 and x = 0.29, changes in the critical points (blue-shifts) with increasing Al composition at 300 K for the $Al_xGa_{1-x}N$ film were observed via ellipsometric measurements for the first time.

• Journal of the Korean Vacuum Society
• /
• v.20 no.1
• /
• pp.7-13
• /
• 2011

[ $L1_0$ ]phase FePd nano-dot structures were successfully fabricated on self-organized Fe/Au bilayers. With atomic force microscopy, it is determined that surface morphologies of initially flat Fe/Au bilayer films were agglomerated and transformed their shape into nano-dots structures with increasing annealing temperature. With this bilayer as a template, FePd multilayers were deposited at various temperatures, i.e. $300^{\circ}C$, $350^{\circ}C$, $400^{\circ}C$, and $450^{\circ}C$. Surface morphologies of FePd superlattice had a near resemblance to self-organized bilayer. According to X-ray diffraction results, it is confirmed that $L1_0$ superlattice structures of FePd were obtained from samples which were annealed above $350^{\circ}C$. Results of X-ray photoelectron spectroscopy depth-profile analysis showed that chemical composition is identical to deposition sequence. As a result, without additional etching processes, fabrication of chemically ordered FePd superlattice nano-dots was achieved.

• The Journal of the Petrological Society of Korea
• /
• v.5 no.1
• /
• pp.35-51
• /
• 1996

The granitic rocks in the vicinity of the Mt. Sorak, the northeastern part of the NE-SW elongated Mesozoic granitic batholith in the Kyeonggi massif, consist of granodiorite, biotite granite, two-mica granite and alkali feldspar granite. Variations In major and most trace elemental abundances show a typical differentiation trend in a granitic magma. Granitic rocks all display a calc-alkaline trend in the AFM diagram. Also, In the ACF diagram discriminating between I- and S-type granitic rocks, granodiorite and most biotite granite in the southeastern area represent I-type and magnetite-series characteristics, while most biotire granite and two-mica granite in the northwestern area exhibit S-type and ilmenite-series ones.According to recent studies of the granitle rocks In the Inje-Hongcheon district. all ihe granitic rocks distributed in the northeastern part of the Kyeonggi massif have been classified as late Triassic to early Jurassic Daebo granite. With reference of the formerly published ages, an age oi $125.6{\pm}4.4$ Ma calculated by the slope in the plot of $^{87}Rb/^{86}Sr-^{87}Sr/^{86}Sr$ for the biotite granite samples from the southeastern area is inferred as an emplacement age for the granitic rocks in the vicinity of the Mt. Sorak. On the basis of elemental variations and Sr isotope compositions, an possible evolutional process for the granitic magmas in this area is suggested. The primary magma of I-type and magnetite-series generated about 125 Ma by partial melting of igneous originated crustal materials, might be emplaced and evolved through fractional crystallization, convection and assimilation of the surrounding Precambrian metasediments to become S-type and ilmenlte-serles in the outer area, and then solidified to granodiorite, biotite granite and two-mica granite.At the latest stage, the evolved hydrothermal solution altered the formerly solidified biotite granite to alkali feldspar granite and probably later local igneous activities affected the alkali feldspar granite again.

• Korean Journal of Optics and Photonics
• /
• v.18 no.5
• /
• pp.351-361
• /
• 2007

The samples composed of a GST thin film and the protective layers of $ZnS-SiO_2$ or $Al_2O_3$ coated on c-Si substrate were prepared by using the magnetron sputtering method. Samples of three different structures were prepared, that is, i) the GST single film on c-Si substrate, ii) the GST film sandwiched by the protective $ZnS-SiO_2$ layers on c-Si substrate, and iii) the GST film sandwiched by $Al_2O_3$ protective layers on c-Si substrate. The ellipsometric constants in the temperature range from room temperature to $700^{\circ}C$ were obtained by using the in-situ ellipsometer equipped with a conventional heating chamber. The measured ellipsometric constants show strong variations versus temperature. The variation of ellipsometric constants at the temperature region higher than $300^{\circ}C$ shows different behaviors as the ambient medium is changed from in air to in vacuum or the protective layers are changed from $ZnS-SiO_2$ to $Al_2O_3$. Since the long heating time of 1-2 hours is believed to be the origin of the high temperature variation of ellipsometric constants upon the heating environment and the protective layers, a PRAM (Phase-Change Random Access Memory) recorder is introduced to reduce the heating time drastically. By using the PRAM recorder, the GST samples are heated up to $700^{\circ}C$ decomposed preventing its partial evaporation or chemical reactions with adjacent protective layers. The surface image obtained by SEM and the surface micro-roughness verified by AFM also confirmed that samples prepared by the PRAM recorder have smoother surface than the samples prepared by using the conventional heater.

• The Journal of the Petrological Society of Korea
• /
• v.12 no.1
• /
• pp.16-31
• /
• 2003

The granites in the southern Gimcheon area can be divided into two parts, marginal hornblende biotite granodiorite (Mgd) and central biotite granodiorite to granite (Cgd). Mgd and Cgd are gray in color and display gradational contact relations and are mainly composed of coarse-grained and medium-grained rocks, respectively. Mgd has more frequent and larger mafic enclaves than Cgd, and the two granites partly show parallel foliation at thire contact with gneisses. From representative samples of the granites, K-Ar biotite ages of 197∼207 Ma were obtained. Considering the blocking temperature of biotite, it is suggested that the emplacement age of the granitic magma was probably late Triassic. The anorthite contents of plagioclases in Mgd display less variation than those of Cgd, indicating that Mgd crystallized within a narrow range of temperatures. In the Al$\_$total/-Mg diagram, the biotites from the granites plot within the subalkaline field, and the smooth slope indicates differentiation from a single magma. All amphiboles from the granites belong to magnesio-hornblende. The linear trends of major oxides, AFM and Ba-Sr-Rb indicate that Mgd and Cgd were fractionally differentiated from a single granitic magma body crystallizing from the margin inwards. The relations of modal (Qz+Af) vs. Op, K$_2$O vs. Na$_2$O, Fe$_2$ $O_3$ vs. FeO, Fe$\^$+3/(Fe$\^$+3/+Fe$\^$+2/) and K/Rb vs. Rb/Sr show that they belong to I-type and magnetite-series granitic rocks developed by the progressive melting products of fixed sources. REE data, normalized to chondrite value, have trends of enriched LREE and depleted HREE together with weakly negative Eu anomalies.

• Journal of the Korean Magnetics Society
• /
• v.17 no.3
• /
• pp.120-123
• /
• 2007

The typical double-barrier magnetic tunnel junction (DMTJ) structure examined in this paper consists of a Ta 45/Ru 9.5/IrMn 10/CoFe7/$AlO_x$/free layer/AlO/CoFe 7/IrMn 10/Ru 60 (nm). The free layer consists of an $Ni_{16}Fe_{62}Si_8B_{14}$ 7 nm, $Co_{90}Fe_{10}$ (fcc) 7 nm, or CoFe $t_1$/NiFeSiB $t_2$/CoFe $t_1$ layer in which the thicknesses $t_1$ and $t_2$ are varied. The DMTJ with an NiFeSiB-free layer had a tunneling magnetoresistance (TMR) of 28%, an area-resistance product (RA) of $86\;k{\Omega}{\mu}m^2$, a coercivity ($H_c$) of 11 Oe, and an interlayer coupling field ($H_i$) of 20 Oe. To improve the TMR ratio and RA, a DMTJ comprising an amorphous NiFeSiB layer that could partially substitute for the CoFe free layer was investigated. This hybrid DMTJ had a TMR of 30%, an RA of $68\;k{\Omega}{\mu}m^2$, and a of 11 Oe, but an increased of 37 Oe. We confirmed by atomic force microscopy and transmission electron microscopy that increased as the thickness of NiFeSiB decreased. When the amorphous NiFeSiB layer was thick, it was effective in retarding the columnar growth which usually induces a wavy interface. However, if the NiFeSiB layer was thin, the roughness was increased and became large because of the magnetostatic $N{\acute{e}}el$ coupling.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.183-183
• /
• 2009

OLED소자의 양극재료로써 현재는 산화인듐주석(ITO : indium tin oxide) 박막이 널리 이용되고 있다. 그러나 낮은 전기 비저항과 높은 투과도를 갖는 ITO 박막을 얻기 위해서는 $300^{\circ}C$ 이상의 고온에서 성막되어야 하며, 원료 물질인 인듐의 수급량 부족으로 인한 문제점과 독성, 저온증착의 어려움, 스퍼터링 시 음이온 충격에 의한 막 손상으로 저항의 증가의 문제점이 있고, 또한 유기발광소자의 투명전극으로 쓰일 경우에 유기물과의 계면 부적합성, 액정디스플레이의 투명전극으로 사용될 경우에 $400^{\circ}C$정도의 놓은 온도와 수소 플라즈마 분위기에서 장시간 노출 시 열화로 인한 광학적 특성변화가 문제가 된다. 이러한 문제점을 지닌 ITO 박막을 대체할 수 있는 물질로 산화 인듐아연(lZO) 박막이 많은 각광을 받고 있다. IZO(Indium Zinc Oxide) 박막은 저온 ($100^{\circ}C$ 이상)에서 증착이 가능하고 추가적인 열처리 없이도 가시광 영역에서 90% 이상의 광 투과도와 ${\sim}10^{-4}{\Omega}cm$ 이하의 낳은 전기 비저항을 갖는 것으로 알려져 있다. 이러한 IZO박막은 성막 후 고온의 열처리 과정이 필요 없기 때문에 폴리카보네이트와 같은 유기물 기판을 사용하여 제작 가능한 유연한 평판형 표시 소자의 제작에도 적용될 수 있다. IZO(Indium Zinc Oxide) 박막은 상온 공정에서도 우수한 전기적, 광학적, 표면 특성을 나타낼 뿐만 아니라 양극재료로써 높은 일함수를 가지고 있어 고효율의 유기 발광 소자를 구현하는데 유리한 재료라 판단된다. 본 연구에서는 TCO 박막의 면 저항과 표면 거칠기가 OLED 소자의 성능에 미치는 영향을 조사하였다. R.F Magnetron Sputtering을 이용하여 투명 전도막을 성막 형성 하였으며, 기판온도와 증착과정에서 주입되는 산소, 수소의 유랑 변화가 박막의 구조적, 전기적 특성에 어떠한 영향 미치는 것인가를 자세히 규명하였다 ITO 와 IZO박막은 챔버 내 다양한 가스 분위기(Ar, $Ar+O_2$ and $Ar+H_2$) 에서 R.F Magnetron Sputtering 방법으로 증착했다. TCO박막의 구조적인 이해를 돕기 위해서 X-ray diffraction 과 FESEM으로 분석했다. 광학적 투과도와 박막의 두께는 Ultraviolet Spectrophotometer(Varian, cary-500)와 Surface profile mersurement system으로 각각 측정하였다. 면저항, charge carrier농도, 그리고 TCO박막의 이동성과 길은 전기적특성은 Four-point probe와 Hall Effect Measurement(HMS-3000)로 각각 측정한다. TCO 박막의 표면 거칠기에 따른 OLED소자의 성능분석 측면에서는 TCO 박막의 표면 거칠기 조절을 위해 photo lithography 공정을 사용하여 TCO 박막을 에칭 하였다. 미세사이즈 패턴 마스크가 사용되고 에칭의 깊이는 에칭시간에 따라 조절한다. TCO박막의 표면 형태는 FESEM과 AFM으로 관찰하고 그리고 나서 유기메탈과 음극 전극을 연속적으로 TCO 박막위에 증착한다. 투명전극으로 사용되는 IZO기판 상용화를 위해 IZO기판 위에 $\alpha$-NPB, Alq3, LiF, Al순서로 OLED소자를 제작하였다. 전류밀도와 전압 그리고 발광과 OLED소자의 전압과 같은 전기적 특성은 Spectrometer (minolta CS-1000A) 에 의하여 I-V-L분석을 했다.