• 한국연소학회:학술대회논문집
• /
• 2012.11a
• /
• pp.297-299
• /
• 2012

Korea Aerospace Research Institute has been doing researches on the hypersonic propulsion system and hypersonic wind-tunnel since 2000 and started scramjet engine researches from 2005. Total 5 kinds of scramjet engine were designed and tested and two of them were hydrocarbon-fueled scramjet engine. For verifying the own characteristics of each components like the intake and combustor, several component tests were done at the KSPC of JAXA and KARI. In this paper, current scramjet engine research activities of KARI will be described.

• Journal of Aerospace System Engineering
• /
• v.7 no.3
• /
• pp.7-14
• /
• 2013

Hypersonic vehicles over Mach 5 need active cooling or thermal management systems to resolve excessive heating problems on their fuselage and engines. Endothermic fuels are widely used these days not only for the energy source but also for a heat sink. Therefore, fuel supply systems of hypersonic vehicles should be mainly composed of adiabatic fuel storage tank, cooling systems for the airframe and engine/nozzle, and fuel supply/injection systems in high pressure, high temperature, and high fuel flow rate conditions. This paper describes a conceptual design process of a hypersonic fuel supply system in order for designing a layout of the system, and identifying components and their specification requirements.

• Journal of computational fluids engineering
• /
• v.2 no.2
• /
• pp.35-43
• /
• 1997

An efficient inverse method for 1.he supersonic/hypersonic axisymmetric body design is developed for the parabolized Navier-Stokes equations. The developed method is examined numerically for three extreme testcases in the supersonic(M/sub ∞/=3.0) and hypersonic(M/sub ∞/=6.28) speeds. The first one is a negative pressure distribution near a vacuum pressure and the second one is a positive pressure distribution over the whole region of the body. The last one is the case of abrupt change of pressure distribution to zero in the forward region of the body. These testcases show the robustness of the method. By introducing a regular-falsi method and by using a not-fully converged inverse solution, the convergence behavior was greatly improved.

• Advances in aircraft and spacecraft science
• /
• v.2 no.2
• /
• pp.109-124
• /
• 2015

This paper deals with the aerodynamic and aerothermodynamic trade-off analysis of a hypersonic flying test bed. Such vehicle will have to be launched with an expendable launcher and shall re-enter the Earth atmosphere allowing to perform several experiments on critical re-entry phenomena. The demonstrator under study is a re-entry space glider characterized by a relatively simple vehicle architecture able to validate hypersonic aerothermodynamic design database and passenger experiments, including thermal shield and hot structures. A summary review of the aerodynamic characteristics of two flying test bed concepts, compliant with a phase-A design level, has been provided hereinafter. Several design results, based both on engineering approach and computational fluid dynamics, are reported and discussed in the paper.

• International Journal of Aeronautical and Space Sciences
• /
• v.14 no.3
• /
• pp.215-221
• /
• 2013

The basic quantitative tool for the study of hypersonic rarefied flows is the direct simulation Monte Carlo method (DSMC). The DSMC method requires a large amount of computer memory and performance and is unreasonably expensive at the first stage of spacecraft design and trajectory analysis. A possible solution to this problem is approximate engineering methods. However, the Monte Carlo method remains the most reliable approach to compare to the engineering methods that provide good results for the global aerodynamic coefficients of various geometry designs. This paper presents the calculation results of aerodynamic characteristics for spacecraft vehicles in the free molecular, the transitional and the continuum regimes using the local engineering method. Results and methods would be useful to calculate aerodynamics for new-generation hypersonic vehicle designs.

• Bulletin of the Korean Space Science Society
• /
• 2004.10b
• /
• pp.328-331
• /
• 2004

Shock wave boundary layer interactions can make flows around a vehicle be very high pressure and temperature due to pass shock waves in small areas of the hypersonic vehicle. These phenomena can affect a critical problem in the design of hypersonic vehicles. To research the effect of shock wave boundary layer interactions, comer flows were studied in this paper using numerical studies with the NSMB (Navier-Stokes Multi Block) solver and then comparing corresponding numerical results with experimental data of the Huston High Speed Flow Field Workshop II. The mach number of flows is 12.3 in comer flows. The comparison with the computational result is presented based on diverse numerical schemes. Good agreement is obtained.

• 한국전산유체공학회:학술대회논문집
• /
• 1999.05a
• /
• pp.29-34
• /
• 1999

A two-dimensional Navier-Stokes code based on AUSMPW+ scheme has been developed to simulate the hypersonic flowfield of hypersonic shock-shock interaction. AUSMPW+ scheme is a new hybrid flux splitting scheme, which is improved by introducing pressure-based weight functions to eliminate the typical drawbacks of AUSM-type schemes, such as non-monotone pressure solutions. To study the real gas effects, three different gas models are taken into account in this paper: perfect gas, equilibrium flow and nonequilibrium flow. It has been investigated how each gas model influences on the peak surface loading, such as wall pressure and wall heat transfer, and unsteady flowfield structure in the region of shock-shock interaction. With the results, the value of peak pressure is not sensitive to the real gas effects nor to the wall catalyticity. However, the value of peak heat transfer rates is affected by the real gas effects and the wall catalyticity. The structure of the flowfield also changes drastically in the presence of real gas effects.

• International Journal of Aerospace System Engineering
• /
• v.2 no.2
• /
• pp.62-66
• /
• 2015

The starting processes of the Ludwieg tube hypersonic quiet tunnel plays very important role in the achievement of the quiet flow in the test section, which could affect the confidence coefficient of the data in the hypersonic transition experimental investigations. Thus, numerical analysis on that processes could help to understanding the running mode of the Ludwieg tube quiet tunnel and the propagation principle of the expansion wave series. To verify our computational method, the same parameter of the BAM6QT (the Boeing/AFOSR Mach-6 quiet tunnel at Purdue University) is used to compute, and it is agrees with our computational results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.649-656
• /
• 2004

Hypersonic wind tunnel test of the rectangular variable geometry intake is performed. For realization of a Precooled turbojet engine, development of a hypersonic ramjet engine is planned. To investigate performance of the intake of the hypersonic ramjet engine, wind tunnel test is done with freestream Mach number of 5.1. The total pressure recovery was 18 % with 12.9 % of ramp bleed. Several reasons for low total pressure recovery are shown. Supersonic internal compression is not enough. Then, the throat Mach number is high (M2.61) and total pressure losses at the terminal shock is large. Supersonic flow at the throat and position of the terminal shock is sensitive to a difference of the second ramp's throat height and the third ramp's throat height. Flow separations at the second ramp's trailing edge and the third ramp's leading edge are seen those could result in the trigger of unstart. The seal mechanism between the ramps and the sidewalls is important.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.268-271
• /
• 2010

Hypersonic engine test facility with ejector system was tested. Ejector system was designed by revised EJSIMP code. The performance of the ejector system was predicted by numerical analysis. As a result, ejector system satisfied the facility design requirement. Based on the pressure level, the facility was successfully started at Mach 3.5 and 20km altitude condition.