• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.124-127
• /
• 2007

In this study, we focused on investigation of governing parameters affected on the fatigue properties in the hyper-eutectoid steel wires used for TBR tires. Steel wires are fabricated under different drawing strain from 3.36 to 3.80. Their diameters are 0.21 mm and 0.185mm, respectively. The fatigue properties was measured by hunter rotating beam tester, specially designed thin-sized steel wires. The results showed that the fatigue properites of steel wire, marked as A-1, were greater than the others, due to the low value of residual stress. In order to elucidate the variations of fatigue properties, the microstructure, surface defect and residual stress were observed and measured by useful analysis technique, such as TEM, 3D profiler and FIB.

• 소성∙가공
• /
• 제25권5호
• /
• pp.306-312
• /
• 2016

Effects of manufacturing conditions, such as austenitizing temperature, patenting temperature and carbon content in steels, on mechanical properties, especially on reduction of area (RA), of hyper-eutectoid steel wires were investigated. RA increased and then decreased with transformation temperature. This was attributed to the presence of abnormal structures in steels transformed at low transformation temperatures and the occurrence of shear cracking during tensile testing of steels transformed at high transformation temperatures. The increase of austenitizing temperature resulted in the increased austenite grain size and consequently the decrease of RA. The decrease of RA with increasing the carbon content in steels was attributed to the increased fraction of cleavage fracture in tensile fractured surfaces.

• 열처리공학회지
• /
• 제26권3호
• /
• pp.126-131
• /
• 2013

In this study, effects of silicon addition on the spheroidizing annealing of hyper-eutectoid steel was investigated. Heat treatment at various temperatures in the ${\gamma}+{\theta}$ region was also conducted in order to systematically control the kinetics of undissolved cementite. It was found that small amount of Si addition could increase both $A_1$ and $A_{cm}$ transformation temperature by both the JMat Pro evaluation and dilatometric measurement. It was also revealed by the microstructural observation that the volume fraction of retained cementite during heat treatment increased with decreasing temperature as well as increasing Si content. Based on the results obtained, it could be suggested that spheroidization at relatively higher temperature above $950^{\circ}C$ could be achieved by small addition of Si.

• 소성∙가공
• /
• 제25권6호
• /
• pp.359-365
• /
• 2016

The rate-controlling mechanisms for time-dependent plastic deformation of eutectoid and hyper-eutectoid pearlitic steels at low $T/T_m$ temperatures were explored. The strain rate - stress data obtained from a series of constant load tensile tests at $0.25{\sim}0.30T/T_m$ were applied to the power law, the lattice friction controlled plasticity, and the obstacle controlled plasticity. Of these models, the obstacle controlled plasticity was found to best-describe the rate-controlling mechanism for time-dependent plastic deformation of two steels at low $T/T_m$ temperatures in terms of the activation energy for overcoming the obstacles against dislocation glide in ferrite. The deformed microstructures revealed the dislocation forests of a high density as the main obstacles. In addition, the obstacle controlled plasticity well-explained the effects of cementite on the $0^{\circ}K$ flow stress of two steels.

• 소성∙가공
• /
• 제17권2호
• /
• pp.91-96
• /
• 2008

The governing parameters affecting the fatigue properties have been investigated experimentally in the high carbon steel wires with 0.94 wt.%C. In order to find the crucial factors, the advanced analysis techniques such as optical 3-D profiler, focused ion beam(FIB) and transmission electron microscope(TEM) were used. The two-type steel wires with different drawing strain were fabricated. The fatigue properties were measured by hunter rotating beam tester, specially designed for thin-sized steel wires. It was found that the fatigue properties of the steel wires with high drawing strain was higher than that with other wires because of low residual stress and high adhesion condition of brass coating layer.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.120-123
• /
• 2007

The effects of annealing condition on the occurrence of the delamination in cold drawn hyper-eutectoid steel wires, were investigated. Annealing treatment was performed on cold drawn steel wires for temperature range of $425^{\circ}C\sim500^{\circ}C$ with the variation of annealing time from 30sec to 15min. The increase of annealing temperature and time would cause the decrease of tensile strength and the increase of ductility. However, the occurrence of the delamination, representing torsional ductility, showed the different way from the variation of ductility.

• 대한금속재료학회지
• /
• 제46권3호
• /
• pp.111-117
• /
• 2008

The effects of the dissolved cementite on the mechanical properties have been experimentally investigated. The steel wires were fabricated depending on the carbon content of 0.82 and 1.02 wt.% and drawing strain from 4.12 to 4.32. The bending fatigue resistance and torsion ductility were measured by a hunter fatigue tester and torsion tester specially designed for thin-sized wires. The results showed that as the drawing strain and carbon content increased, the fatigue resistance and the torsional ductility of the steel wires decreased, while the tensile strength increased. In order to elucidate this behavior, the microstructure in terms of lamellar spacing (${\lambda}_p$), cementite thickness ($t_c$) and morphology of cementite was observed by advanced analysis techniques such as transmission electron microscope (TEM) and 3 dimensional atom probes (3-D AP).