• The International Journal of Costume Culture
• /
• 제4권3호
• /
• pp.241-248
• /
• 2001

Re water resistance of shell fabrics intended for we in outdoor apparel was measured using three different standard test methods, ASTM D 751, hydrostatic resistance, procedure A(Mullen test -- with and without a fabric support) and Procedure B (Hydrostatic head test). A database of information on their water resistance performance was created. The data collected with different methods were correlated and the advantages and disadvantages of each method were compared. The Mullen test with a support appears to give higher and more favorable water resistance values on shell fabrics preventing fabric rupture during the test. The hydrostatic head test gave lower hydrostatic pressure values than those measured on the two Mullen tests. The Mullen test is recommended for testing the water resistance of fabrics that high a relatively high water resistance because the Mullen tester applies a wide range of pressure. The hydrostatic head test is recommended for testing the fabrics that have relatively low water resistance. The area of the fabric sample that is in contact with the water is smaller in the Mullen test, so higher pressure levels can be reached and more samples should probably be tested to get a representative value for each fabric types. Furthermore, the hydrostatic head test was deemed more repeatable than the Mullen tests in his study.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.377-380
• /
• 2000

The collapsible phenomena of the circular tubes due to the excessive transmural pressure are investigated experimentally. Collapsible tubes are installed in the test section where the external pressure is applied to the test tubes by applying the hydrostatic head. The collapsible circular tubes are made of rubber, whose diameters are 6 and 4.2 mm, respectively. The hydrostatic water head of the upper reservoir is applied to the test section. Pressures at the upstream and downstream sides are measured by the pressure transducers. The collapsible phenomena are observed as the transmural pressure Increases, and also the flutter phenomenon occurs due to the critical transmural pressure.

• The Korean Journal of Physiology
• /
• 제7권1호
• /
• pp.13-21
• /
• 1973

An attempt was made to study circulatory and respiratory responses to the passive tilt. Anesthetized dogs were tilted from horizontal to upright $(+90^{\circ})$ and head down $(-90^{\circ})$ position. The arterial blood pressure was decreased in the upright position and was decreased slightly in the head down position comparing to that in the horizontal position. Cardiac index also decreased in the both upright and head down positions. The total systemic vascular resistance was slightly increased in the upright position and was markedly increased in the head down position. The mean pulmonary arterial pressure was significantly decreased in the both upright and head down positions. The total pulmonary vascular resistance was decreased in the both upright and head down positions. Oxygen consumption was slightly decreased in the upright position, whereas it was slightly increased in the head down position. The A-V $O_2$ difference (vol. %) was slightly increased in the upright position and increased in the head down position. From the above results, process of the circulatory compensation to the gravity in the Passive tilting test was discussed. Neuronal cardiovascular regulation to the gravity and tile adaptation of capacitance vessles to hydrostatic stress and oxygen consumption concerning anoxic endurance of the brain were also discussed.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제3권1호
• /
• pp.20-26
• /
• 2011

A weakly nonlinear seakeeping methodology for predicting motions and loads is presented in this paper. This methodology assumes linear radiation and diffraction forces, calculated in the frequency domain, and fully nonlinear Froude-Krylov and hydrostatic forces, evaluated in the time domain. The particular approach employed here allows to overcome numerical problems connected to the determination of the impulse response functions. The procedure is divided into three consecutive steps: evaluation of dynamic sinkage and trim in calm water that can significantly influence the final results, a linear seakeeping analysis in the frequency domain and a weakly nonlinear simulation. The first two steps are performed employing a three-dimensional Rankine panel method. Nonlinear Froude-Krylov and hydrostatic forces are computed in the time domain by pressure integration on the actual wetted surface at each time step. Although nonlinear forces are evaluated into the time domain, the equations of motion are solved in the frequency domain iteratively passing from the frequency to the time domain until convergence. The containership S175 is employed as a test case for evaluating the capability of this methodology to correctly predict the nonlinear behavior related to wave induced motions and loads in head seas; numerical results are compared with experimental data provided in literature.

• Journal of Biosystems Engineering
• /
• 제8권2호
• /
• pp.62-68
• /
• 1983

This study was to examine the drying characteristics of barley and the effect of moisture content of barley on milling performance. A barley variety, Jogang, having 35.0% of initial moisture content was used for this experiment. Thermo-hydrostatic dryer which consists of blower, condensor, heater, humidifier, drying chamber and control box, etc., was used for the drying experiment. The change in the weight of a barley sample was continuously measured by means of the ring type load cell installed inside the drying chamber. Milling test runs the samples having the predetermined moisture content were taken from each drying test run. A laboratory type barley miller was used for the milling test. The results of the study are summarized as follows: 1. The drying constants (k) applied for the thin layer drying model, (M-Me)/(Mo-Me) = $Ae^{-kt}$ were 0.155, 0.259 and 0.548, respectively, at the three levels of drying temperatures, $40^{\circ}C$, $50^{\circ}C$ and $60^{\circ}C$. The drying constants complied with the Arrhenius Equation, K = Ko exp (-C/T), were determined as $Ko=1.901455{\times}10^8$ and C = 6563. 2. The laboratory milling test indicated that the highest milled and head barley recovery was resulted from the sample which was dryed at $40^{\circ}C$. In general, the increase in the drying temperature from $40^{\circ}C$ to $60^{\circ}C$ indicated a negative effect on milling yields. 3. Also, the sample having 15% M.C. presented the highest milled and head barley recovery among the five moisture content levels (12, 15, 18,21 and 24%).

• 대한기계학회논문집A
• /
• 제36권10호
• /
• pp.1235-1239
• /
• 2012

원자력발전소의 원자로압력용기 상부헤드에는 출력제어 및 정지용 제어봉이 통과하는 노즐이 있으며 이 노즐은 상부헤드 노즐과 J 형태의 홈으로서 용접 되어 있다. 최근 외국의 원자력발전소에서 이 용접영역 주변의 노즐 및 용접부에서 일차수응력부식 균열이 발생한 사례가 보고되고 있다. 본 논문에서는 이 용접부의 용접잔류응력과 운전 중에서의 응력상태를 유한요소해석을 이용하여 평가함으로써 고응력 위치를 확인하고 응력관점에서 균열발생 가능성이 높은 지역을 예측하고자 하였다. 해석결과 용접에 의해서 형성된 잔류응력이 수압시험과 운전조건에 의해 다소 변동되기는 하나 응력분포형태는 큰 변화가 없었다. 전반적으로 노즐내면에서는 용접이 시작되는 지점 주변에서 최대 인장응력이 형성되고 노즐외면에서는 용접이 끝나는 지점 주변에서 최대인장응력이 형성되는 것을 확인하였다.