• 제목/요약/키워드: Hydrophobic filtration

검색결과 77건 처리시간 0.026초

응집제 주입에 따른 NOM과 저압막의 막오염 특성에 관한 연구 (A study on the fouling characteristics of low-pressure membranes and NOM with coagulation pretreatment)

  • 박상혁;홍종현;유명진;구자용
    • 상하수도학회지
    • /
    • 제24권2호
    • /
    • pp.237-246
    • /
    • 2010
  • This study was carried out to compare the performances of hydrophobic and hydrophilic membranes in the filtration of the pretreatment waters using coagulants such as PAC and PAHCs, and to investigate the influence of NOM characteristics on the fouling of membranes. As a result, the hydrophobic fraction was more effectively removed by PAHCs, however the transphilic and hydrophilic fraction were more effectively removed by PAC on NOM removal. Raw water showed the highest response in the range of humic substances, and pre-coagulated waters with PAC and PAHCs followed. It was also observed that the fouling effect for a hydrophobic membrane was greater than that of a hydrophilic membrane with a similar pore size, due to fouling caused by adsorption. Foulants causing significant flux decline were alcoholic compounds (polysaccharide-like) and humic substances including aromatic groups. Especially, it appeared that alcoholic compounds such as polysaccharide-like substances which mostly remained after coagulation pretreatment had most influence on fouling. It was found that fouling were influenced by each fraction NOM components depending on coagulants used. And PAHCs was more efficient for membrane fouling than PAC.

Water transport through hydrophobic micro/nanoporous filtration membranes on different scales

  • Mian, Wang;Yongbin, Zhang
    • Membrane and Water Treatment
    • /
    • 제13권6호
    • /
    • pp.313-320
    • /
    • 2022
  • Theoretical calculation results are presented for the enhancement of the water mass flow rate through the hydrophobic micro/nano pores in the membrane respectively on the micrometer and nanometer scales. The water-pore wall interfacial slippage is considered. When the pore diameter is critically low (less than 1.82nm), the water flow in the nanopore is non-continuum and described by the nanoscale flow equation; Otherwise, the water flow is essentially multiscale consisting of both the adsorbed boundary layer flow and the intermediate continuum water flow, and it is described by the multiscale flow equation. For no wall slippage, the calculated water flow rate through the pore is very close to the classical hydrodynamic theory calculation if the pore diameter (d) is larger than 1.0nm, however it is considerably smaller than the conventional calculation if d is less than 1.0nm because of the non-continuum effect of the water film. When the driving power loss on the pore is larger than the critical value, the wall slippage occurs, and it results in the different scales of the enhancement of the water flow rate through the pore which are strongly dependent on both the pore diameter and the driving power loss on the pore. Both the pressure drop and the critical power loss on the pore for starting the wall slippage are also strongly dependent on the pore diameter.

Membrane Filtration Technology for Drinking Water Treatment & Night Soil Treatment

  • Kato, Yasuhiko
    • 한국막학회:학술대회논문집
    • /
    • 한국막학회 1998년도 제6회 하계 Workshop (98 한국막학회, 국립환경연구원 국제 Workshop, 수자원 보전과 막분리 공정)
    • /
    • pp.155-170
    • /
    • 1998
  • 1. The flux for hydrophilic CA membrane is higher than that for hydrophobic PES membrane at any operating conditions. The difference in bpth fluxes becomes greater as the water recovery is lower. 2. Backwash pressure should be more than twice as high as filtration pressure in order to maintain the higher flux. Backwash frequency is independent of the flux when the UF is operated under the same water recovery. 3. The relatively lower crossflow velocity of around 0.1 m/s would be appropriate because of the lower energy consumption per treated water. 4. The membrane fouling occurring at high turbidity and high concentration of organic compounds in raw water can reduce the flux and increase the removal of the organic compounds. 5. It is confirmed by the pilot plant testing that the UF by using the CA membrane module was well applicable to the drinking water treatment.

  • PDF

The Anticoagulant Fraction from the Leaves of Diospyros Kaki L. Has an Antithrombotic Activity

  • Sa You Seon;Kim Soo-Jin;Choi Hye-Seon
    • Archives of Pharmacal Research
    • /
    • 제28권6호
    • /
    • pp.667-674
    • /
    • 2005
  • The leaves of Persimmon (Diospyros kaki L.) has long been used for tea in Korea since it was thought to be effective against hypertension. An anticoagulant fraction was purified through gel filtration G-100, hydrophobic, gel filtration G-150, and FPLC, Phenyl superpose column chromatographies. The purified fraction was homogenous and its Mr was estimated 10,000 Da by gel filtration and SDS-PAGE. The purified fraction was sensitive to treatment of subtilisin B, but not to heat and its activity was not changed after periodate oxidation, indicating that the activity was not due to carbohydrates. It delayed thrombin time (TT), activated partial thromboplastin time (APTT), and prothrombin time (PT) using human plasma. TT was more sensitive than APTT and PT, suggesting that the anticoagulant activity may be caused by a degradation or a defect of fibrin or thrombin. It did not cause the hydrolysis of fibrin after incubation. However, it inhibited thrombin-catalyzed fibrin formation with a competitive inhibition pattern. These results indicate that it may be an antithrombotic agent and that it is bound to fibrinogen binding sites of thrombin.

Effect of coagulation conditions on ultrafiltration for wastewater effluent

  • Maeng, Sung Kyu;Timmes, Thomas C.;Kim, Hyun-Chul
    • Membrane and Water Treatment
    • /
    • 제8권2호
    • /
    • pp.185-199
    • /
    • 2017
  • Low-pressure membrane filtration is increasingly used for tertiary treatment of wastewater effluent organic matter (EfOM), mainly comprising organic base/neutral compounds. In-line coagulation with underdosing, charge neutralization, and sweep floc conditions prior to ultrafiltration (UF) was studied to determine removals of the EfOM components and consequent reduction of fouling using polyethersulfone membranes. Coagulation and UF substantially reduced fouling for all coagulation conditions while removing from 7 to 38% of EfOM organic acids. From 7 to 16% of EfOM organic base/neutrals were removed at neutral pH but there was no significant removal for slightly acid coagulation conditions even though fouling was substantially reduced. Sweep floc produced the lowest resistance to filtration but may be inappropriate for in-line use due to the large added volume of solids. Charge-neutralization resulted in poor recovery of the initial flux with hydraulic cleaning. Under-dosing paralleled sweep floc in reducing hydraulic resistance to filtration (for sub-critical flux) and the initial flux was also easily recovered with hydraulic cleaning. Hydrophobic and hydrophilic base/neutrals were identified on the fouled membranes but as previously reported the extent of fouling was not correlated with accumulation of organic base/neutrals.

연근의 polyphenol oxidase 정제 및 특성조사 (Purification and Characterization of Polyphenol Oxidase from Lotus Root (Nelumbo nucifera G.))

  • 문상미;김현진;함경식
    • 한국식품과학회지
    • /
    • 제35권5호
    • /
    • pp.791-796
    • /
    • 2003
  • 박피된 절편 연근의 갈변억제를 효과적으로 하기 위한 기초연구로 갈변의 주원인 효소인 polyphenol oxidase(PPO)를 분리, 정제하여 특성을 조사하였다. 박피된 절편 연근을 24시간 동안 $4^{\circ}C$에 방치하여 PPO 활성을 증가시켜 조효소액을 제조하였으며 PPO 조효소액을 acetone으로 침전시킨 후 Q-Sepharose anion-exchange column, Phenyl-Sepharose hydrophobic interaction column의 conventional column과 Mono-Q anion-exchange column, Superdex 75 gel-filtration column의 HPLC column을 이용하여 PPO 활성이 가장 높은 한 개의 PPO isoform LPIII-2를 최종 분리 정제하였다. 분리 정제된 LPIII-2의 분자량을 gel-filtration chromatography를 이용하여 측정한 결과 56kDa이었으며 SDS-PAGE를 실시한 후 silver staining한 결과 LPIII-2의 분자량은 28kDa와 26kDa으로 2개의 band를 형성하는 것으로 보아 heterodimer인 것으로 추정되었다. PPO isoform의 특성 조사를 위하여 Q-Sepharose anion-exchange chromatography를 이용하여 부분분리 정제된 2개의 isoforms(LP-II, LP-III)를 가지고 기질 특이성을 조사한 결과 LP-II의 경우 $5^{\circ}C$$30^{\circ}C$ 모두 catechol에 대한 기질 친화력이 높았으며 LP-III의 경우 $5^{\circ}C$$30^{\circ}C$ 모두에서 pyrogallol에 기질 친화력이 높았다. 그리고 pH 7에서 최적 pH를 보였으며 열안정성은 $40^{\circ}C$에서 60분간 열처리했을 때 안정하였지만 $60^{\circ}C$에서 40분, $80^{\circ}C$에서 10분간 열처리했을 때 효소가 불활성화되었다. 특이하게도 연근의 PPO는 다른 과채류의 PPO와 반응온도에 따른 특성이 달랐는데 여러 반응온도에서 효소 활성을 측정한 결과 연근 PPO isoform LP-II와 LP-III 모두 $5^{\circ}C$의 반응온도에서 높은 효소활성을 보였으며 온도가 올라갈수록 반응속도가 떨어지는 특성을 보였다.

막오염에 미치는 유기물 분자량 분포특성 및 화학적 구조특성 (Effect of Organic Melecular Weight and Functional Group on Membrane Fouling)

  • 정철우;손희종;신현준;손인식
    • Korean Chemical Engineering Research
    • /
    • 제45권6호
    • /
    • pp.669-676
    • /
    • 2007
  • 낙동강 매리지역 원수에 대해 유기물 성상분석을 한 결과, 소수성 물질이 43%, 친수성 물질이 39%, 반친수성 물질이 18%를 차지하고 있는 것으로 나타났으며, 각각의 유기물질에 대한 분자량 크기 분포 특성을 살펴보면 소수성 > 반친수성 > 친수성 물질의 순으로 분자량 분포특성을 보였다. 막 공극 크기에 따른 영향을 살펴본 결과 막 공극 크기가 증가할수록 공극 내에서 공극 막힘현상과 공극 흡착현상이 막오염의 주된 메카니즘으로 작용하여 투과 flux 감소율이 크게 나타나는 것으로 조사되었다. 막의 재질에 따른 영향을 살펴본 결과 소수성 막의 경우 친수성 막에 비하여 소수성 상호반응(hydrophobic interaction)에 의하여 유기물에 의한 막 오염 현상이 발생하여 투과 flux 감소율이 더 크게 나타나고 초기 투과 flux 감소율도 빠르게 진행되었다. 원수에 대한 막의 재질과 막의 공극크기에 따른 막오염 메카니즘 분석결과 소수성 재질의 막에서 막표면 오염을 나타내는 Kc, 막의 공극흡착현상을 나타내는 Ks, 막의 공극 막힘현상을 나타내는 Ki 값이 상대적으로 크게 나타났다. 막의 공극 크기에 따른 막 오염 메카니즘 분석결과 막의 100 kDa 이상의 공극이 큰막의 경우에는 소수성 계열의 유기물이 막의 공극 내부에서 막 오염을 유발하였으며, 10 kDa 정도로 공극이 작은 막의 경우 소수성과 친수성 계열 유기물이 막 표면에서 막 오염을 유발하는 메카니즘이 주원인으로 작용하였다

강변여과에서 콜로이드 물질과 오염물의 거동에 관한 연구 (Transport of Colloids and Contaminant in Riverbank Filtration)

  • 이상일;김대환;이상신;유상연
    • 한국수자원학회논문집
    • /
    • 제39권6호
    • /
    • pp.511-520
    • /
    • 2006
  • 강변여과는 강물을 강변의 충적대수층에 통과시켜 지층의 자체정화능력을 이용하여 오염물질을 상당량 저감시킨 후 양수하는 방식이다. 국내에서는 대부분의 원수를 지표수에서 취수하여 사용하고 있는 실정이나, 오염물질의 증가로 인하여 지표수를 원수로 사용하기가 점점 어려워지고 있다. 강변여과를 이용하여 양질의 원수를 확보하기 위해서는 오염물 이동에 관한 이해가 중요하다. 본 연구에서는 대수층에 용존성 유기물질(DOM)과 박테리아가 동시에 존재할 경우를 대상으로 대수층을 4상(four-phase: 흙입자, 물, 박테리아, 용존성 유기물질)으로 모델링하고, 이들의 물리, 화학, 생물학적 특성을 고려하여 물질의 거동을 기술하는 수학적 모델을 제시하였다. DOM과 박테리아와 같은 콜로이드성 물질은 오염물의 이동을 가속시키고, 평형 분배계수가 중요한 역할을 하는 인자인 것으로 나타났다.

오일/물 에멀젼의 분리막 투과 특성 (Membrane Filtration Characteristics of Oil/Water Emulsions)

  • 김종표;임진수;유종훈;김재진;정건용;전명석;민병렬
    • 청정기술
    • /
    • 제5권2호
    • /
    • pp.69-78
    • /
    • 1999
  • 수용성 에멀젼형 절삭유의 한외여과 및 정밀여과 특성을 실험적으로 연구하였다. 한외여과막의 경우 오일/물 에멀젼의 투과 거동은 film model을 잘 따랐으나 정밀여과막인 ASYPOR막의 경우에는 이러한 거동을 벗어났다. 본 연구에서 사용된 모든 분리막의 경우 운전압력이 투과유속에는 큰 효과를 나타내지 않았다. 저압에서는 투과 초기 및 후기에서의 투과유속 감소율이 적은 반면 고압에서는 초기 투과유속은 매우 컸으나 투과유속의 감소율이 커서 후기에는 모두 비슷한 투과유속을 보여 주었다. 소수성이 큰 polycarbonate 정밀여과막의 경우 일반적인 경우와는 달리 운전시간이 증가함에 따라 투과유속이 증가하는 경향을 나타내었다. 교반하지 않은 cell에서의 임계투과압력은 150 ppm의 에멀젼 농도에서 약 $2.2kg_f/cm^2$이었으나 500 ppm의 농도에서는 $3.8kg_f/cm^2$ 압력에서 나타났다.

  • PDF

Combination of Hydrophobic Filtration and Enrichment Methods for Detecting Bacillus cereus in Fresh-Cut Cabbage

  • Lee, Sujung;Choi, Yukyung;Lee, Heeyoung;Kim, Sejeong;Lee, Jeeyeon;Ha, Jimyeong;Oh, Hyemin;Lee, Yewon;Kim, Yujin;Yoon, Yohan;Lee, Soomin
    • 한국식품위생안전성학회지
    • /
    • 제33권5호
    • /
    • pp.325-329
    • /
    • 2018
  • 본 연구에서는 신선편이 양배추 내 Bacillus cereus의 최적 증균 온도를 선정하고 증균배양액에 소수성필터를 적용하여 multiplex PCR의 검출률을 확인하였다. B. cereus 증균온도는 B. cereus 균주 5 개를 혼합하여 1 Log CFU/mL이 되도록 증균배지에 접종하고 $30^{\circ}C$, $37^{\circ}C$, $42^{\circ}C$에서 증균한 뒤 3시간 간격으로 MYP agar에 도말한 후 계수하여 선정하였다. 소수성필터 미적용 그룹은 B. cereus 균주 5 개를 혼합하여 신선편이 양배추에 접종한 뒤 최적 증균온도에서 증균하였으며, 증균배양액을 가열하여 DNA를 추출한 뒤 multiplex PCR을 진행하였다. 소수성필터 적용 그룹은 증균배양액을 소수성 필터에 적용하고 필터에 있는 균을 멸균증류수로 현탁한 뒤 가열하여 추출된 DNA로 multiplex PCR을 진행하였다. 증균온도 확인 결과, 6시간 증균 시 $42^{\circ}C$에서 증균된 샘플($5.4{\pm}0.3Log\;CFU/mL$)과 $30^{\circ}C$에서 증균된 샘플($4.6{\pm}0.6Log\;CFU/mL$) 간 유의차가 확인되었다(p < 0.05). 소수성필터 적용 유무에 따른 multiplex PCR 결과, 1 Log CFU/g 접종된 샘플의 검출률이 소수성 필터 적용 전 60%(3/5)에서 100%(5/5)로 향상되었다. 2 Log CFU/g 접종 샘플은 소수성필터 적용 전 80%(4/5)에서 소수성 필터 적용 후 100%(5/5)로 검출률이 증가하였으나, 3 Log CFU/g 접종 샘플은 소수성 필터 적용 전후 모두 100%(5/5)로 확인되었다. 이상의 결과를 통해 신선편이 양배추 내 B. cereus 검출 시 증균배양액에 소수성필터를 적용하고 multiplex PCR을 적용했을 때 신속하고 효율적인 검출이 가능할 것으로 판단된다.