• Water Engineering Research
• /
• 제2권2호
• /
• pp.123-138
• /
• 2001

An injection experiment was carried ut to investigate the pressure domain within which hydromechanical coupling influences considerably the hydrologic behavior of a granite rock mass. The resulting database is used for testing a numerical model dedicated to the analysis of such hydromechanical interactions. These measurements were performed in an open hole section, isolated from shallower zones by a packer set at a depth of 275 m and extending down to 840 m. They consisted in a series of flow meter injection tests, at increasing injection rates. Field results showed that conductive fractures from a dynamic and interdependent network, that individual fracture zones could not be adequately modeled as independent systems, that new fluid intakes zones appeared when pore pressure exceeded the minimum principal stress magnitude in that well, and that pore pressures much larger than this minimum stress could be further supported by the circulated fractures. These characteristics give rise to the question of the influence of the morphology of the natural fracture network in a rock mass under anisotropic stress conditions on the effects of hydromechanical couplings.

• 한국정밀공학회지
• /
• 제12권7호
• /
• pp.131-137
• /
• 1995

The performance analysis is applied to the transmission of the tracked vehicle, comparing simulation results with vehicle test. The calculation method of hydrostatic pump/motor performance and power circulation is used for hydromechanical transmission simulation. And various shifting characteristics is analyzed by studying power flow at each range.

• Journal of Biosystems Engineering
• /
• 제41권3호
• /
• pp.145-152
• /
• 2016

Purpose: This study aims to establish the effect of pinhole position errors in the planet carrier of a planetary gear set (PGS) on load sharing among the planet gears in the hydromechanical transmission (HMT) system of an agricultural tractor. Methods: A simulation model of a PGS with five planet gears was developed to analyze load sharing among the planet gears. The simulation model was verified by comparing i ts r esults w ith those of a model developed in a previous s tudy. The verified simulation model was used to analyze the load-sharing characteristics of the planet gears with respect to the pinhole position error and the input torque to the PGS. Results: Both simulation models had identical load magnitude sequences for the five planet gears. However, the load magnitudes on the corresponding planet gears differed between the models because of the different stiffnesses of the PGS components and the input torques to the PGS. The verified simulation model demonstrated that the evenness of load sharing among the planet gears increases with decreasing pinhole position error and increasing input torque. Conclusions: The geometrical tolerance of the pinhole position should be properly considered during the design of the planet carrier to improve the service life of the PGS and load sharing among the planet gears.

• 한국지반환경공학회 논문집
• /
• 제10권2호
• /
• pp.61-68
• /
• 2009

본 논문은 수리학적 현장 주입시험 기간 동안 고려될 필요가 있는 수리역학적 상호작용에 따른 균열암반매질의 수리학적 거동에 대한 수치적 연구이다. 이러한 주입시험은 굴착정 내에 설치된 개구간(open hole section)을 따라 높은 압력을 가진 유량을 주입하며, 이를 통해 굴착정을 가로지르는 균열로부터 유량을 측정하는 것이다. 시간에 따라 변화되는 유량측정결과는 수리역학적 상호작용에 대한 분석 및 예측을 위해 개발된 수치모형의 현장 적용성을 평가하기 위해 사용되었다. 유량측정결과 전도성이 있는 균열들은 상호의존적인 균열망을 형성하며, 이로 인해 균열망을 구성하는 개별적인 균열요소들은 독립적인 시스템으로서 적절하게 모형화 될 수 없음을 보여주었다. 또한 간극수압이 굴착정 주위에 작용하는 최소주응력을 초과할 때 새로운 유체유입영역이 발생되며, 이러한 최소주응력보다 훨씬 큰 간극수압은 굴착정 주위의 균열들에 의해 유지될 수 있다는 것을 보여주었다. 본 연구에서 이러한 특성들이 자연 상태의 균열망의 구성형태에 따라 어떻게 영향을 미치게 되는지 이산 균열망 모형을 통해 수치적으로 분석되었다.

• 드라이브 ㆍ 컨트롤
• /
• 제12권4호
• /
• pp.96-100
• /
• 2015

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.519-524
• /
• 2001

In this paper, power flow characteristics of a hydromechanical transmission(HMT) are investigated using network analysis. The HMT used in this study consist of a hydrostatic unit(HSU), planetary gear sets, clutches and brakes providing forward 4 speeds and backward 2 speeds. Since the HMT power flows showing a closed loop and the HSU efficiency varies depending on the pressure and speed, a systematic approach is required to analyze the power transmission characteristics of the HMT. In order to analyze the closed loop power flow and the HSU power loss which changes depending on the pressure and speed, network model is constructed for each speed range. In addition, an algorithm is proposed to calculate an accurate HSU loss corresponding to the experimental results. It is found from the network analysis that the torque and speed of each transmission element including the HSU can be obtained as well as direction of the power flow by the proposed algorithm. It is expected that the network analysis can be used in the design of relatively complicated transmission system such as HMT.

• 대한기계학회논문집A
• /
• 제26권6호
• /
• pp.1149-1158
• /
• 2002

An improved hydrostatic unit(HSU) model is proposed by considering the flow loss in order to analyze the power flow characteristics of a hydromechanical transmission(HMT) and a network analysis algorithm is presented to determine the torque and speed of each element of the HMT. To calculate the torque and flow loss of a pump and a motor in HSU, an effort and flow concept is introduced, which can be used to establish a torque and speed matrix in the network analysis. It is found from the network analysis that magnitude of the HSU stroke increases to maintain the same output speed in order to compensate the flow Boss in the HSU and the efficiency of the HMT shows the lowest value in the 1st speed since the HSU has the largest flow loss in the 1st speed and the flow loss decreases as the speed ratio upshifts.

• 대한기계학회논문집A
• /
• 제26권12호
• /
• pp.2615-2623
• /
• 2002

In this paper, a systematic design approach for a three shaft hydromechanical transmission(HMT) system is proposed by considering the power characteristics and speed ratio range. Using network analysis, possible configurations of the 3 shaft HMT are analyzed and it is found that the influence of HSU stroke on the power distribution of the HMT can be investigated by the network analysis. In addition, design methods are presented from the viewpoint of (1) power distribution and (2) speed ratio range. From the power distribution and the speed ratio range, a HMT configuration can be constructed, which minimizes the power circulation and provides the desired speed ranges. Based on the 3 shaft HMT analyses and the proposed design approach, a 3 shaft HMT is designed which provides 4 speeds in forward and 1 speed in reverse while keeping the power circulation less than 150% of the input power. It is expected that the design method suggested in this study can be used in a systematic design of the 3 shaft HMT.

• 한국수산과학회지
• /
• 제34권3호
• /
• pp.245-253
• /
• 2001

곰소만 조간대에서 채취한 표층퇴적물에 대하여 입도분석을 수행하여 퇴적물의 조직 특성을 분석하였다. 코어 시료를 이용하여 퇴적물의 수리-역학적 특성을 실험적으로 도출하였으며, 퇴적물의 심도별 역학적 응력 및 과잉간극수압, 그리고 지반의 안정성을 수치해석적으로 분석하여 바지락 양식장 퇴적물의 거동 특성을 규명하였다. 곰소만 조간대내의 표층 퇴적물은 겨울에는 $5 \phi$의 조립 실트가 주를 이루는 단모드형을 나타내고, 여름에는 $5 \phi$의 조립 실트질 퇴적물에 $4 \phi$의 미세사질 퇴적물이 첨가된 경향을 보여준다 바지락 양식장의 퇴적환경은 평균 입도 $4\~5 \phi$범위, 모래함량 $50\%$ 미만, 니질 함량 $5\sim10\%$ 범위를 나타낸다. 퇴적양상은sandy silt이며, 분급도는 $1.0\sim2.0 \phi$를 나타내고, 왜도는 0.1-0.5의 범위에 포함되어 퇴적물의 퇴적 작용이 방해가 될만한 높은 에너지 상태가 지속되지 않는 환경이 바지락 양식에 양호한 것으로 조사되었다. 수치해석적 결과를 토대로 볼 때, 바지락 양식에 양호한 저질환경은 사질과 니질이 혼합되어 절대 투수계수가 $10^{-11}\sim10^{-12}m^2$ 범위인 경우로 사료되며, 수치해석 모델링 견과 니질 피복층의 두께가 4cm를 초과하게되면 바지락 서식에 대한 저질환경은 크게 저하되고 있는 것으로 고찰된다.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1854-1862
• /
• 2001

In this paper, power flow characteristics of a hydromechanical transmission(HMT) are investigated using network analysis. The HMT used in this study consist of a hydrostatic unit(HSU), planetary gear sets, clutches and brakes providing forward 4 speeds and backward 2 speeds. Since the HMT power flows showing a closed loop and the HSU efficiency varies depending on the pressure and speed, a systematic approach is required to analyze the power transmission characteristics of the HMT. In order to analyze the closed loop power flow and the HSU power loss which changes depending on the pressure and speed, network model is constructed fur each speed range. In addition, an algorithm is proposed to calculate an accurate HSU loss corresponding to the experimental results. It is found from the network analysis that the torque and speed of each transmission element including the HSU can be obtained as well as direction of the power flow by the proposed algorithm. It is expected that the network analysis can be used in the design of relatively complicated transmission system such as HMT.