• Journal of Drive and Control
• /
• v.14 no.2
• /
• pp.1-8
• /
• 2017

The spool displacement of a directional control valve can be considered as the standard signal for the measurement of its bandwidth frequency. When the spool displacement is not available, the metering-orifice system is suggested in this study as an alternative way to measure the - 3 dB amplitude-ratio bandwidth frequency of the hydraulic directional-control valve. The amplitude ratio of the metering-orifice pressure can be adjusted to equal that of the spool displacement through the controlling of the metering-orifice opening area. A series of experiments were conducted to verify the effectiveness of the metering-orifice system. The metering orifice was confirmed as adequate for the measurement of the - 3 dB amplitude-ratio bandwidth frequency.

• Journal of Drive and Control
• /
• v.12 no.4
• /
• pp.60-70
• /
• 2015

A front-end loader (FEL) mounted on an agricultural tractor is one of the most commonly used implements for farm work. However, when the tractor carries material using the bucket attached to the FEL on a sloping ground, the materials can spill or roll back over the operator due to the tilted body, thereby requiring the bucket surface to remain level at a constant value regardless of varying slopes. In this study, an active system for controlling the angle of the FEL bucket on a tractor based on the real-time measurement of ground slopes was developed to enable the bucket to constantly remain level. A FEL simulator operated based on an electro hydraulic proportional valve (EHPV) was constructed in the laboratory to develop a proportional-integral-derivative (PID) controller forming a virtual electronic control unit (ECU) on the computer, which could automatically adjust the bucket angles depending on varying input angles while sending SAE-J1939 associated messages via CAN BUS to the EHPV. The different parameter values for the PID controller due to the gravity effect of the bucket were determined using a manual PID tuning method while assuming that the tractor travels on either an ascending slope or a descending slope. The developed PID control-based self-leveling system showed a mean of steady-state errors of within $1^{\circ}$ and a mean of delayed times of ~ 0.8s when the step input of $+20^{\circ}$ was given, implying that the developed system and control algorithm would be effective in maintaining the bucket angle at a certain value. Future studies include the improvement of the control algorithm to reduce such a time delay as well as the application of the developed algorithm to the FEL mounted on a tractor tested at a testing ground.

• Journal of Korea Water Resources Association
• /
• v.55 no.spc1
• /
• pp.1211-1222
• /
• 2022

Abnormal condition inevitably occurs during operation of water distribution system (WDS) and requires the isolation of certain areas using isolation valves. In general, the determination of the optimal location of isolation valves considered minimization of hydraulic failures as isolation of certain areas causes a change in hydraulic states (e.g., flow direction, velocity, pressure, etc.). Water quality failure can also be induced by changes in hydraulics, which have not been considered for isolation valve system design. Therefore, this study proposes a new isolation valve system design methodology to prevent unexpected water quality failure events. The new methodology considers flow direction change ratio (FDCR), which accounts for flow direction changes after isolation of the area, as a constraint while reliability is used as the objective function. The optimal design model has been applied to a synthetic grid network and the results are compared with the traditional design approach. Results show that considering FDCR can eliminate flow direction changes while average pressure and coefficient of variation of pressure, velocity, and hydraulic geodesic index (HGI) outperform compared to the traditional design approach. The proposed methodology is expected to be a useful approach to minimizing unexpected consequences by traditional design approaches.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1684-1687
• /
• 1997

A dynamic load simulator which can reproduce on-ground the hinge moment of aircraft control surface is and essential rig for the loaded performance test of aircraft test of aircraft acutation system. The hinge moment varies wide in the aricraft flight enveloped depending on specific flight condition and maneuvering status. To replicate the wide spectrum of this hinge moment variation within some accuracy bounds, a force controller is designed based on the Quantiative Feedback Theory (AFT). Through the analysis on hinge moment dynamics, a design specification for the force controller is suggested. The efficacy of QFT force controller is verivied by simulation, in which combined aricraft dynamics/flight control law and hydraulic actuation system dynamics of aircraft control surface are considered.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.342-347
• /
• 2003

In this paper, an active vibration control of a translating tensioned string with the use of an electro-hydraulic servo mechanism at the right boundary is investigated. The dynamics of the moving strip is modeled as a string with tension by using Hamilton’s principle for the systems with changing mass. The control objective is to suppress the transverse vibrations of the strip via boundary control. A right boundary control law in the form of current input to the servo valve based upon the Lyapunov’s second method is derived. It is revealed that a time-varying boundary force and a suitable passive damping at the right boundary can successfully suppress the transverse vibrations. The exponential stability of the closed loop system is proved. The effectiveness of the control laws proposed is demonstrated via simulations.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.208-211
• /
• 1993

This paper presents the parameter design method for the desired time response of hydraulic track motor system of an industrial excavator. The dynamic response depends upon many component parameters such as motor displacement, spring constant and various valve coefficients. Most of them are to be determined to obtain the desired response while some parameters are fixed, or discrete for the off-the-shelf type components. The parameters might be selected through repeated simulations of the system once the system is mathematically represented. This paper, however, presents optimization technique to select two parameters using a parameter optimization technique. The variational approach is applied to the system equations which are represented as state equations and from those system equations derived are the adjoint equations. The gradients for each parameter also are formed for the iterations.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.205.2-205.2
• /
• 2011

Micro hydraulic turbines take a growing interest because of its small and simple structure as well as high possibility of applying to micro and small hydropower resources. The differential pressure exiting within the city water pipelines can be used efficiently to generate electricity like the energy generated through gravitational potential energy in dams. In order to reduce water pressure at the inlet of water cleaning centers, pressure reducing valves are used widely. Therefore, pressure energy is wasted. Instead of using the pressure reduction valve, a micro counter-rotating hydraulic turbine can be replaced to get energy caused by the large differential pressure found in the city water pipelines. In this study, in order to acquire design data of counter-rotating tubular type micro-turbine, output power, head, and efficiency characteristics due to the diffuser.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.218-223
• /
• 1997

유압장치의 핵심부품인 유압 제어밸브(hydraulic control valve)는 유압펌프 등에 의하여 가압된 유압유의 압력과 유량을 제어하고 유동방향을 변화시키는 주요기능을 수행한다. 특히, 대부분의 제어밸브는 스푸울(spool)과 슬리브(sleeve)를 기본구조로 채용하고 있다. 피스톤 형상인 스푸울이 슬리브내를 왕복운동하면 스푸울과 슬리브 사이의 간극(clearance)에서는 점성유체인 유압유의 윤활작용에 의하여 원주방향으로 비대칭인 유체압력이 발생한다. 이 결과로 스푸울에 측력(lateral force)이 작용하며, 조건에 따라서는 스푸울에 작용하며, 조건에 따라서는 스푸울에 작용하는 마찰력이 증대할 뿐만 아니라 스푸울과 슬리브의 내벽에 과도한 마멸(wear)을 유방시키기도 하여 제어밸브의 성능을 크게 저하시키기도 한다. 유압공학분야서는 이를 유체고착(hydraulic locking) 현상이라고 부른다. 본 논문에서는 항공기 Flap actuator의 Selector manifold에서 사용되는 스푸울 밸브의 성능에 큰 영향을 미칠 것으로 예상되는 스프울과 슬리브 사이 간극에서의 윤활특성을 이론적으로 조사하고자 한다.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.2 no.3
• /
• pp.12-17
• /
• 2005

This paper presents a theoretical study of the delivery flow ripple produced by a swash plate type hydraulic piston pump for the purpose of developing a computer simulation program capable of predicting the pump source flow ripple accurately at the design stage. Particular attention has been paid to the development of the theoretical model by clarifying quantitatively the design influences of key parts of valve plate such as relief groove and pre-compression/expansion.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.3
• /
• pp.1-6
• /
• 2010

This paper deals with the issue of simple adaptive position control for a pump-controlled cylinder system. A fixed displacement pump is utilized instead of servo valve and its speed is controlled by AC motor. The whole control system is composed of a pair of interconnected subsystems, that is, a feedback control system and a feedforward control system. From experiments it is shown that position control using simple adaptive control can accomplish significant reduction in position tracking error comparing to a conventional PID control.