• 한국터널지하공간학회 논문집
• /
• 제4권1호
• /
• pp.57-70
• /
• 2002

국토의 65 % 이상이 산악으로 구성된 이유로 90년대 이후 산악지형의 암반을 대상으로 한 대규모 교통터널, 에너지 비축시설 및 산업용 저장소와 같은 대형 토목구조물의 필요성이 크게 증가하고 있다. 암반내 시공되는 토목 구조물의 설계과정에서 현지 암반의 초기응력장에 대한 정량적인 자료가 주요한 핵심요소로 작용하며 이러한 초기응력장에 대한 제반 정보를 획득하기 위한 목적으로 국내에서는 정밀 지반조사 과정에서 수압파쇄법이 대표적으로 사용되고 있다, 본 논문에서는 국내 각지의 산악지형에서 얻어진 수압파쇄시험 현장 측정 자료들에 대한 해석결과를 바탕으로 국내 산악지형의 암반내 초기응력 분포 특성에 대한 분석을 수행하였다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.39-44
• /
• 2008

The heat exchange between the Borehole Heat Exchanger(BHE) and the surrounding ground depends directly on ground thermal conductivity k at the certain site. The k is thus a key parameter in designing BHE and coupled geothermal heat pump systems. Currently, although a thermal hydraulic response test(TRT) is mostly used in practice, the thermal hydraulic TRT needs additional power and is generally time-consuming. A new, simple wireless P/T probe for a hi-speed k determination was introduced in this paper. This technique using a wireless P/T probe is less time-consuming and requires no external source of energy for measurement and predicts local thermal properties by measuring soil temperatures along the depth. Measured temperature data along the depth was analyzed. In order to verify the new technique for the determination of ground thermal conductivity, ground thermal conductivity k that calculated from the measured temperature data using a wireless P/T probe was compared with one obtained from conventional hydraulic TRT. When comparing the average k of two methods, the relative error was approximately 10%. As a result, the electronic TRT can replace the conventional hydraulic TRT method after carrying out the additional research on a lot of sites.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.711-716
• /
• 2003

This paper presents the inverse dynamic analysis of the hydraulic excavator manipulator based on the experimental data. A three dimensional rigid multi-body model of the hydraulic excavator manipulator was built up. Inverse dynamic analysis for typical operation mode was carried out by the ADAMS program. In order to verify the analysis results with the measured, the hydraulic pressure and displacement of the cylinders were measured and the dynamic analysis was carried out using experimental data. From the results of the cylinder driving forces, good agreements are obtained between the analysis and the measurement.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1030-1033
• /
• 2003

The packing-free piston has become widely distributed in certain branches of instrument making and precision machine building. A large number of the most diversified instruments are now being constructed on the principle of the packing-free piston like piston manometers, vacuum manometers, hydraulic machines, dynamometers. hardness measuring instruments. power indicators, hydraulic scales, and many others. In spite of the widespread application of systems with a packing-free piston, there were practically no special papers to the theory and practice of the application of such systems. This paper describes the theoretical approaching method to get the pressure distribution profile between the piston and cylinder using finite element method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1672-1675
• /
• 2003

In this study, we developed full automation test system for pressure vessel. This pressure vessel containing oxygen, nitrogen and carbon is widely used in industrial field. The test items of pressure vessel are divided into three branches which is weight measurement, water-hydraulic, and leakage test. After leakage test is completed, cleaning and dry progress is carried out. And control system is consist of three controller which is PLC, monitoring system and database system. PLC is control all of system. Monitoring system measures weight, pressure, flow etc and display to all conditions. Database system stores tested data. we design system to control all test modules in communication by a second period with three control modules. Finally, we verified this system by field test.

• 소음진동
• /
• 제10권4호
• /
• pp.623-628
• /
• 2000

This paper presents the automatic plumbness measuring system form improving the accuracy and working time for plumbness measuring of semi-umbrella type hydraulic turbine generator. It is general practice that rotating shaft should run within acceptable vibration limit. In order to obtain more accurate measuring data for single stage shaft on the semi-umbrella type, plumbness approach must be established carefully and accurately. Generally, present plumbness procedure is required several calculation algorithm, laser sensor and data acquisition devices. As a result of application to actual new system it is confirmed that working time could be saved over 80% and accurate measurement data could be acquired.

• 대한기계학회논문집
• /
• 제16권2호
• /
• pp.191-199
• /
• 1992

This paper presents in experimental study of the dynamic internal pressure within an oil hydraulic vane pump. The measurements of the dynamic internal pressures near the vane of a pressure balance type of an oil hydraulic vane pump with intravanes has been made to provide the essential information for the study of the pump dynamics and control, the pump design and the analysis of tribological problems in the sliding components. The influences of the discharge pressure and rotating speed of the vane on the dynamic pressure in four chambers surrounding a vane have been investigated. The results indicate that the surge pressures of the chambers at the instant moment of discharge and closure are affected by the rotating speed. The pressure in the intravane chamber maintains almost constant values, which remarkably effects the pulsating discharge pressure.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권8호
• /
• pp.947-953
• /
• 2007

Occurrence of pressure pulsation in positive displacement hydraulic turbine is one of the principal problems which should be cleared to improve the turbine performance and to put the turbine to practical use. Therefore, present study is tried to examine the occurrence mechanism and characteristics of the pressure pulsation CFD analysis and experimental measurement are implemented in this study to clarify the phenomena of unsteady pressure pulsation. The results show that occurrence reason of the pressure pulsation is not only due to a series of opening and closing of the chamber formed between rotor and casing wall but also due to the variation of rotational speed of following rotor. The pressure pulsation causes torque variation and the curve patterns of the torque variation conforms to that of the pressure pulsation. Pressure in the chamber is equal to the averaged value of inlet and outlet pressures. Sudden pressure decrease by accelerated through-flow between lobe and casing wall results in torque loss.

• 유공압시스템학회논문집
• /
• 제4권3호
• /
• pp.22-27
• /
• 2007

The source flow ripple and the source impedance in hydraulic pump are characteristic values showing fluid-borne vibration characteristics decisively. We cannot measure these two characteristic values directly, but can measure them by some indirect methods. One representative indirect measuring method is ISO 10767-1. The authors constructed a hardware and a software for the measuring method based on ISO 10767-1. Through the error evaluation of the measured results, accuracy of the measuring method using ISO 10767-1 was examined in detail.

• International Journal of Precision Engineering and Manufacturing
• /
• 제5권1호
• /
• pp.55-59
• /
• 2004

This study developed a fully automated test system for pressure vessels, containing such as oxygen, nitrogen, which is widely used in many industries. The pressure vessel test has three major parts including weight measurement test, water-hydraulic test and leakage test followed by cleaning and drying. The control system for these tests consists of three parts: a PLC, a monitoring system and a database management system. The PLC oversees overall control of test machines, while the monitoring system measures and displays weight, pressure, flow etc. for every situations, and the database management system stores test data. These three modules are designed to communicate with one another at 1 Hz frequency alerting problematic situations to the operator. The system has gone through actual field tests for verification of performances.