• Nuclear Engineering and Technology
• /
• v.49 no.5
• /
• pp.968-978
• /
• 2017

Three small-break loss-of-coolant accident (SBLOCA) tests with safety injection pumps were carried out using the integral-effect test loop for SMART (System-integrated Modular Advanced ReacTor), i.e., the SMART-ITL facility. The types of break are a safety injection system line break, shutdown cooling system line break, and pressurizer safety valve line break. The thermal-hydraulic phenomena show a traditional behavior to decrease the temperature and pressure whereas the local phenomena are slightly different during the early stage of the transient after a break simulation. A safety injection using a high-pressure pump effectively cools down and recovers the inventory of a reactor coolant system. The global trends show reproducible results for an SBLOCA scenario with three different break locations. It was confirmed that the safety injection system is robustly safe enough to protect from a core uncovery.

• Journal of Korean Society of Disaster and Security
• /
• v.11 no.2
• /
• pp.83-89
• /
• 2018

The significant sedimentation at the estuary in the eastern coast of Korea frequently causes river mouth occlusion where disconnection between the river and sea is observed. River mouth occlusion causing watershed retention raises the environmental risk of the area as it impairs water quality and threatens the area's safety in the event of floods. This study proposes a plan to maintain stability of river channel and flow of flood discharge at the estuary with loss of its function for disaster prevention. To this end, the study tries to change the location and width of stream path, focusing on the center line of stream near the sand bar of river mouth. This allows to identify a shape of stream path that leads the most stable flow. To review the result, this study uses the SRH-2D, a model for two-dimensional hydraulic analysis, and conduct numeric simulation. The simulation result showed that the most effective plan for maintaining the stable flow of running water without having the area sensitive to changes in hydraulic characteristics is to lower the overall river bed height of the sand bar near the center line of stream to a equal level.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.12
• /
• pp.47-55
• /
• 2009

As a conventional line-fitting method, the Bouwer and Rice method has been popularly adopted to estimate the hydraulic conductivity of an aquifer through a slug test. Because a vertical cutoff wall is usually very compressible and features a small wall thickness, the Bouwer and Rice method should be carefully applied to analyzing slug test results to estimate the hydraulic conductivity of vertical cutoff walls. In addition, a relatively impermeable layer, called a filter cake, formed at the interface between the cutoff wall and the natural soil formation makes it difficult to use the Bouwer and Rice method directly. In order to overcome such limitations, the original Bouwer and Rice method has been modified by incorporating the concept of the flow net method. In this modification, the geometry condition of cutoff walls including the filter cake is effectively considered in evaluating the hydraulic conductivity of a vertical cutoff wall.

• Water for future
• /
• v.14 no.2
• /
• pp.53-62
• /
• 1981

In the Hydraulic Structure, Such as dam body or levee of river that is constructed with soil, We analyzed a top line of free ground water table. This study is based on the logical reason that the pressure on the free surface is atmospheric and the seepage line is a stream line. In order to research for the unknown seepage line. We analyzed seepage water of steady flow through parous media by Finite Element method based on Galerkin Principle, and compared the comluted value with experimental value. The results show that the computed value was nearly equal to the experimental value. Finally, it noticed that finite Element method was more practical than Experimental Method for Seepage line analysis.

• Nuclear Engineering and Technology
• /
• v.41 no.5
• /
• pp.655-676
• /
• 2009

The first-ever integral effect test for simulating a guillotine break of a DVI (Direct Vessel Injection) line of the APR1400 was carried out with the ATLAS (Advanced Thermal-hydraulic Test Loop for Accident Simulation) from the same prototypic pressure and temperature conditions as those of the APR1400. The major thermal hydraulic behaviors during a DVI line break accident were identified and investigated experimentally. A method for estimating the break flow based on a balance between the change in RCS inventory and the injection flow is proposed to overcome a direct break low measurement deficiency. A post-test calculation was performed with a best-estimate safety analysis code MARS 3.1 to examine its prediction capability and to identify any code deficiencies for the thermal hydraulic phenomena occurring during the DVI line break accidents. On the whole, the prediction of the MARS code shows a good agreement with the measured data. However, the code predicted a higher core level than did the data just before a loop seal clearing occurs, leading to no increase in the peak cladding temperature. The code also produced a more rapid decrease in the downcomer water level than was predicted by the data. These observable disagreements are thought to be caused by uncertainties in predicting countercurrent flow or condensation phenomena in a downcomer region. The present integral effect test data will be used to support the present conservative safety analysis methodology and to develop a new best-estimate safety analysis methodology for DVI line break accidents of the APR1400.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.3
• /
• pp.654-662
• /
• 1998

Shift quality of an automatic transmission in a vehicle is mainly affected by transient pressures in the hydraulic system during shifting. In this study, dynamic modelings of the hydraulic system and the power train of an automatic transmission are made systematically by a bond-graph method. The dynamic characteristics of the line pressures and clutch/brake pressures during shiftings are investigated by simulations and verified by experiments. The effects of clutch/brake pressures on the shift torque are also investigated through driving simulation.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.36-46
• /
• 1993

In CVT vehicle, the engine speed is completely decoupled from the vehicle speed within the range from maximum transmission ratio to minimum transmission ratio. This allows the engine to operate in optimal state(e.g. best fuel economy or maximum power mode.) In this study, the CVT control algorithm for optimal operation of engine is suggested. In order to implement the real time digital control of electro-hydraulic CVT system, a software called CVTCON has been developed. CVTCON also includes the CVT operation module, (2) system test module, (3) system control module and (4) data management module. By using the CVTCON and the electro-hydraulic CVT system, two modes of experiments were carried out: constant throttle opening mode and acceleration mode. From the experimental result, it was found that the algorithm suggested in this study showed optimal operation of the CVT system.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.198-205
• /
• 1998

Recently, according as the supply of power steering system has been diffused, for the comfortable driving condition, the problem to reduce the noise and vibration of this system suddenly appeared. This system can be classified two systems of the pipe line and the pump. In this paper, it is described about the noise characteristic with the camring profile of the hydraulic vane pump. As a result, when it excesses tolerance, the noise is increased. Moreover, in the case of the same of cam-ring, the effect of the rotating speed is larger than the discharge pressure.

• Journal of the Korean Society for Precision Engineering
• /
• v.5 no.2
• /
• pp.33-42
• /
• 1988

In a large scale oil hydraulic system having repeatedly operated actuator, such as a large scale forging press, pressure surges often due to the recombination of oil column in a return line attached to the downstream side of a directional control valve. Expecially, the pressure surges appear very severe ones at a certain valve operating frequency. These pressure surges restrict the operating frequency of the hydraulic system. But related reports on the above mentioned phenomenon are rarely to be found. In this study, therefore, the authors investigate the exact reason why such severe pressure surges occur at a certain range of valve operating frequency. The study is performed by experiment and numerical computation on the relationship between pressure surges and valve operating frequency.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.2
• /
• pp.179-182
• /
• 2007

In this study hydraulic model experiment was conducted to identify the performance of newly developed water affinity sea-wall block to keep the coastal line from eroding and supply water affinity space by reflection coefficient and safety. In the result, the block is applicable to the field.