• 소음진동
• /
• 제10권5호
• /
• pp.800-805
• /
• 2000

To determine the modal matrix and modal frequency of engine mount system, we most solve so-called eigen-value problem. However eigen-value problem of engine mount system with hydraulic mount can not be solved by general eigne-analysis algorithm because the properties of hydraulic mount vary with frequency. so in this paper the method for modal analysis of rigid body motions of an engine supported by hydraulic mount is proposed. Natural frequencies and mode shapes of this nonlinear system are obtained by using complex exponential method and Laplace transformation method. In time domain, impulse response functions are calculated by (two-sided) discrete inverse Fourier Transformation of forced frequency response functions achieved by Laplace transformation of the differential equation of motion. Considering the fact that frequency response functions synthesized by modal parameters form proposed method are in good agreement with original FRFs, it is proved that the proposed method is very efficient and useful for the analysis of eigne-value problem of hydraulic engine mount system.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.830-839
• /
• 1993

Agricultural hydraulic robot which was reported in Part Ⅰ had been developed . The robot satisfied performance to intend before development. For actual use, however, it have been necessary to reduce manipulator weigh and to simplify construction of hydraulic control valve. Then, working stress of manipulator link and pressure fluctuation of hydraulic circuit were measured. Step and frequency response tests were done subject to amplitude of reference voltage of 0.1 , 0.3 , 0.5 and 1.0v. and delivery pressure of 3.5 and 5.0MPa. Working stress were about 25% comparing with fatigue strength, Thus, mass of manipulator might be reduce to 30 %. In hydraulic control system, virtual natural frequency of 6.5Hz is produced from the combination of drain passage area shortage of servovalve. Further , because of passage area shortage , working pressure at both side of cylinder was acted on. This phenomenon prevent utilize effectively engine power. Then, control valve for new model was p oposed.

• 한국공작기계학회논문집
• /
• 제11권2호
• /
• pp.71-79
• /
• 2002

In this paper, an oil hydraulic pipeline is terminated by both rotary sinusoidal flow generator at upstream oriffice at down stream. The pulsating pressure wave from generated by the rotary sinusoidal flow generator, is measured by using sensor. In the analysis of this paper, a component of the fundamental frequency is obtained by using Laplace transformation.. The experimental and analytical results make clear that (1) viscosity is significant role in hydraulic pipe. (2) When pulsating frequency is matched with the natural frequency, resonance frequency occured periodically. According to the study proposed here, dynamic pressure in a circular oil pipe is expressed in propagation of pressure wave with respect to frequency and Bessel function. The resonance at oil temperature $20^{\circ}$$0^{\circ}C$ in this study. The abrupt change of gain value is due to effect of resonance frequency. The results of experiment are compared with the calculated results, and agreement of both results is fairly good.

• 항공우주시스템공학회지
• /
• 제12권5호
• /
• pp.54-68
• /
• 2018

본 논문에서는 소형 압전유압펌프에 적용된 체크밸브의 동적 특성이 유량 형성에 미치는 효과에 대한 연구를 수행하였다. 브레이크 시스템 작동을 위한 부하 압력의 형성을 위해서는 압전유압펌프의 유량이 중요한 요소이다. 이때, 유체 내에서 작동하는 체크밸브의 고유 진동수는 압전 유압펌프의 유량 형성에 큰 영향을 미친다. 또한, 체크밸브의 고유 진동수는 체크밸브와 펌프 시트 사이의 간격에 영향을 받는다. 이를 고려하여 본 연구에서는 체크밸브와 펌프 시트 사이의 간격에 따른 체크밸브의 고유진동수를 유체-구조 연성 해석을 통해 산출하였다. 시뮬레이션을 통해 얻은 유량은 개발된 압전유압펌프를 이용한 유량 형성 실험과의 비교를 통해 검증하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.286-292
• /
• 1993

The classical way to improve the control performance is studied on the aspects of gun/turret deive systens. Two ways are discussed comparadively ; electrical case and electro-hydraulic case. System parameters are analytically studied in terms of resonance frequencies, and damping and gear train ratio effects are checked in relation to resonance frequency increase. Benefit of the feedback is discussed to increase the damping of the natural frequency lending to bandwidth increase.

• 한국수산과학회지
• /
• 제38권5호
• /
• pp.316-322
• /
• 2005

In order to develop a floating breakwater, which can efficiently control long period waves, vertical plates are attached in pontoon. Wave control and dynamic behaviors of the newly developed vertical plates type are verified from numerical analysis and hydraulic experiment. As a result, for the wave control and energy dissipation, the newly developed vertical plates type is more efficient than the conventional pontoon type. For the floating body motion, the wave transmission, depending on incident wave period, is decreased at the natural frequency. Dimensionless drift distance has similar trend of the reflection rate of wave transformation near natural frequency except maximum and minimum values. Dimensionless maximum tension is 17 percent of the weight of floating breakwater in case of the conventional pontoon type and 18 percent or 14 percent in case of the newly developed vertical plates type. Thus, it is shown that the wave control is improved by the vertical plates type. In addition, by adjusting the interval of the front and back vertical plate, we would control proper wave control.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.473-478
• /
• 2003

This paper presents static and dynamic measurement of the stress and motion characteristics for crawler type excavators. Eight scenarios were prepared for static measurement based on two extreme digging positions, maximum digging reach position and maximum digging force position. The measured items for static motion included stress, cylinder pressure, cylinder stroke and digging force. The measured static stresses showed that asymmetric digging force acting on a bucket induced higher stress level than symmetric one. The measured static pressures and digging forces also agreed with design pressures and design digging forces, respectively. The dynamic measurement was performed for two types of motion, that is, simple reciprocation of each cylinder and actual digging motion. The measured items for dynamic motion were stroke and pressure of each cylinder, stresses on the working device and acceleration on the upper plate of an arm. The measured data showed that the natural frequency of the excavator highly depended on the hydraulic stiffness of cylinders. Digging motion tests revealed that digging motion was closer to static motion rather than dynamic one.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권6호
• /
• pp.632-638
• /
• 2014

선박용 저속 2행정 디젤엔진의 선체 탑재 후 본체 진동제어를 위한 방법 중 하나로 마찰식 톱브레이싱과 유압식 톱브레이싱의 사용이 널리 이용되고 있으며 이들의 선택은 선주에게 일임되어져 왔다. 특히, 최근에 이르러 톱브레이싱 설치목적에 반하여 선체강성의 상대적 저하는 주 공진회전수를 상용회전수내에 존재하게 만들었고 마찰식 톱브레이싱이 장착된 선박에서 이와 관련된 사고 사례가 보고되었다. 이에 따른 효율적 해결방안으로 다양한 형태의 선박에 대하여 광범위한 진동측정이 제시되었다. 본 논문에서는 이를 바탕으로 톱브레이싱 형식에 따른 엔진 본체 진동의 특성을 확인하였고 엔진 본체 진동을 제어하기 위하여 보다 효율적인 방법에 대하여 고찰하였다.

• 한국기계가공학회지
• /
• 제21권1호
• /
• pp.34-40
• /
• 2022

In this paper, a flow analysis of a swash-plate type hydraulic piston pump installed on a hydraulic flow supply system for marine vessels is presented. A model and governing equations for computational fluid dynamics (CFD) analyses of swash-plate type hydraulic piston pumps were built, and simulation results regarding the internal flow field of the pump were obtained. By analyzing the internal flow of the swash-plate type hydraulic piston pump, we can confirm the time-dependent stroke of each piston as the pump rotates. We also verified that by analyzing the pulsating flow against the slope of the swash plate, the simulation results match well with the experimental results. The natural frequency of the system was computed to be approximately 380 Hz by applying and analyzing the fast Fourier transform (FFT) of each swash plate slope evaluated.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 춘계학술대회 논문집
• /
• pp.597-603
• /
• 2003

Air spring system in railway vehicles primarily ensure the air suspension of the vehicle body. The low natural frequency ensures a comfortable ride and an invariably good stiffness. In this paper, the characteristics and durability test was conducted in laboratory by using servo-hydraulic fatigue testing system to reliability evaluation of air spring for electric railway vehicle. The experimental results show that the characteristics and durability of domestic development productions are obtained the good results.