• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.49 no.1
• /
• pp.1-17
• /
• 2013

The investigation for species composition and catch in the Korean deep-water of the East Sea (also known as Sea of Japan) was carried out with trammel nets of 7 mesh sizes (6.1~24.2cm) offshore Donghae (2006) and Yangyang (2007) of Korea. The catches were 1,268kg and composed of 37 species between 200m and 1,200m in depth. The principal species caught were Taknka's snailfish, salmon snailfish, red snow crab, hunchback sculpin, snow crab, spinyhead sculpin, Tanaka's eelpout, Alaska cod and so on. Those were target fish for commercial value except salmon snailfish. The mesh sizes for the largest catch were 10.6cm and 15.2cm in the fishing ground of Donghae and Yangyang, respectively. The habitat of snow crab was shallower than that of red snow crab in both areas. Trammel net enabled to investigate fish in deep-water with small fishing vessel and rather cheap expenses in contrast to bottom trawl that required too much of it. With increasing inner mesh size of trammel net the mean size of some principal species such as Taknka's snailfish, spinyhead sculpin, hunchback sculpin, Pacific cod, snow crab, red snow crab and hybrid between snow crab and red snow crab tended to be large in certain range of mesh size.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.6
• /
• pp.242-247
• /
• 2012

Yb-doped ITO (ITO:Yb) films were deposited on unheated non-alkali glass substrates by magnetron cosputtering using two cathodes (DC, RF) equipped with the ITO and $Yb_2O_3$ target, respectively. The composition of the ITO:Yb films was controlled by adjusting the RF powers from 0 W to 480 W in 120 W steps with the DC power fixed at 70 W. The ITO:Yb films had a higher crystallization temperature ($200^{\circ}C$) than that of the ITO films ($170^{\circ}C$), which was attributed to both larger ionic radius of $Yb^{3+}$ and higher bond enthalpy of $Yb_2O_3$, compared to ITO. This amorphous ITO:Yb film post-annealed at $170^{\circ}C$ showed a resistivity of $5.52{\times}10^{-4}{\Omega}cm$, indicating that a introduction of Yb increased resistivity of the ITO film. However, these amorphous ITO:Yb films showed a high etching rate, fine pattering property, and a very smooth surface morphology above the crystallization temperature of the amorphous ITO films (about $170^{\circ}C$). The transmittance of all films was >80% in the visible region.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.5
• /
• pp.481-491
• /
• 2017

In this study, we developed 300 W lightweight DMFC system for charging secondary battery in small unit military operation. In order to reduce the volumetric shape and weight of the system considering the environment of the individual soldier's, the arranging of system components has been optimized. A metal bipolar plates made of STS-470FC have been implemented to the DMFC stack to meet the weight demand of the system. As a result of the performance test of the stack, the target value was satisfied by outputting 561 W exceeding 24% of the stack output 450 W required to output 300 W required for the entire system. Moreover, 2,655 hours exceeding 1,000 hours also has been satisfied. To ensure good robustness of the metallic bipolar plate based DMFC stack, finite element method based simulations are conducted using a commercial ANSYS Fluent software.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1335-1340
• /
• 2003

In this paper, a single balanced diode Mixer for the homodyne FMCW radar to detect distance and velocity of a vehicle target is designed and implemented using a microstrip line and two schottky barrier beam lead diodes. This mixer is optimally designed to have less a conversion loss within the 100 MHz bandwidth with a little LO injection power and a higher LO isolation as soon as possible through the embedded electrical length of microsrtrip line placed between the coupler and diode matching, considering together LO matching condition. The measured results show 6 dB of conversion loss, 23 dB LO/RF isolation and 3 dBm of input 1l dB, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.4
• /
• pp.281-288
• /
• 2001

PZT thin films (3500$\AA$) have been prepard on the Ru/Ru $O_2$ and Ru $O_2$ bottom electrodes with a RF magnetron sputtering system using P $b_{1.05}$(Z $r_{0.52}$, $Ti_{0.48}$) $O_3$ ceramic target. Ru/Ru $O_2$ bottom electrode was fabricated by in-situ processing controlled the $O_2$ partial pressure. The PZT thin films deposited on the Ru/Ru $O_2$ bottom electrode were preferred oriented (101) plane. The PZT thin films deposited on the Ru/Ru $O_2$ bottom electrodes showed better electrical properties than those with Ru $O_2$ bottom electrodes because Ru $O_2$ prevented oxygen vacancies and impurities from existing withing the interface and substrate.e.

• Nuclear Engineering and Technology
• /
• v.41 no.10
• /
• pp.1275-1284
• /
• 2009

A directly heated $SO_3$ decomposer for the sulfur-iodine and hybrid-sulfur processes has been introduced and analyzed using the computational fluid dynamics (CFD) code CFX 11. The use of a directly heated decomposition reactor in conjunction with a very high temperature reactor (VHTR) allows for higher decomposition reactor operating temperatures. However, the high temperatures and strongly corrosive operating conditions associated with $SO_3$ decomposition present challenges for the structural materials of decomposition reactors. In order to resolve these problems, we have designed a directly heated $SO_3$ decomposer using RA330 alloy as a structural material and have performed a CFD analysis of the design based on the finite rate chemistry model. The CFD results show the maximum temperature of the structural material could be maintained sufficiently below 1073 K, which is considered the target temperature for RA 330. The CFD simulations also indicated good performance in terms of $SO_3$ decomposition for the design parameters of the present study.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.12
• /
• pp.1125-1131
• /
• 2013

Nowadays, embedded software development using the MATLAB/Simulink system is gradually emerging. Studies generating the parts of embedded S/W in a Rapid Prototype are presented. In this paper, a method to generate the entire embedded S/W of enhanced AC motor control is proposed. High performance motor control could not be achieved with the basic Simulink library and RAppID Toolbox library as it does not have PWM based Interrupt, an ASAC (Analog Sensing for AC Motors) function and other special functions of the Freescale MPC555x. Consequently, the required libraries for enhanced AC motor control are created by Legacy code tool, TLC (Target Language Compiler) and S-Function (System-Function) of MATLAB/ Simulink and utilized in the Rapid Prototype. Motor control performance and execution time are compared automatically to the generated-code S/W with the hand coded S/W. The IPMSM (Interior Permanent Magnet Synchronous Motor) and MPC5553 board that were designed as the AC motor controller for hybrid electrical vehicle are used for the test. The performances meet the requirements and satisfactory results are acquired.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.37 no.3
• /
• pp.63-71
• /
• 2000

Infrared (IR) detector chip, which detects the IR radiation from all of the objects and converts to image signal, is usually fabricated using hybrid bonding technology with detector away and readout integrated circuit (ROIC). In this study, we designed the readout circuit and simulated its operations. Fabricating readout circuit chips, we measured operation results satisfying its design requirements in 6V supply voltage. After we mount the IR detector chip in the manufactured thermal image system, thermal images were implemented. The obtained thermal images for high and room temperature target objects are sufficiently recognizable. Using the low noise thermal Image system, we expect to obtain thermal images with higher temperature resolution.

• Journal of Fisheries and Marine Sciences Education
• /
• v.26 no.3
• /
• pp.485-491
• /
• 2014

The study of Web MGIS(Marine Geographic Information System) based on the SVG(Scalable Vector Graphics) is mainly performed on effective methodologies which transform real world data to computing world data. Web GUI system has its own target on reliable data service by acquisition of geometric information using HYCOM(HYbrid Coordinate Ocean Model), accurate measurement and graphical visualization. This type of raw data visualization can be built without software tools, yet is incredibly useful for interpreting and communicating data. Even simple visualizations can aid in the interpretation of complex hydrodynamic relationships that are frequently encountered in the marine environment. The Web MGIS provides an easy way for hydrodynamic geoscientists to construct complex visualizations that can be viewed with free software. This study proposes a Web GUI MGIS using FVCOM(Finite Volume Coastal Ocean Model). Finally, we design a Marine Web GUI system of Kosrae Coastal Waters integrating above data models. It must adds more ecological information and the various service item for approach more easily in order to user.

• ETRI Journal
• /
• v.37 no.4
• /
• pp.766-771
• /
• 2015

Robust motion estimation for human-computer interactions played an important role in a novel method of interaction with electronic devices. Existing pose estimation using a monocular camera employs either ego-motion or exo-motion, both of which are not sufficiently accurate for estimating fine motion due to the motion ambiguity of rotation and translation. This paper presents a hybrid vision-based pose estimation method for fine-motion estimation that is specifically capable of extracting human body motion accurately. The method uses an ego-camera attached to a point of interest and exo-cameras located in the immediate surroundings of the point of interest. The exo-cameras can easily track the exact position of the point of interest by triangulation. Once the position is given, the ego-camera can accurately obtain the point of interest's orientation. In this way, any ambiguity between rotation and translation is eliminated and the exact motion of a target point (that is, ego-camera) can then be obtained. The proposed method is expected to provide a practical solution for robustly estimating fine motion in a non-contact manner, such as in interactive games that are designed for special purposes (for example, remote rehabilitation care systems).