• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.5
• /
• pp.871-878
• /
• 2013

Roll-to-roll (R2R) hot embossing systems have been developed and are widely used in various industrial domains. These systems press and heat flexible films between a press roll and a back-up roll, as said films pass through the two rolls. In previous studies, a heating roll was used for heating. However, in this study, a hybrid roll for R2R hot embossing is conceptualized and developed. This R2R system can be used for generating fine patterns on large and continuous films. The hybrid roll of our system can cool and heat the films simultaneously, thus affording greater flexibility in process design. Thermal and structural analyses were performed for developing the hybrid roll. In addition, a hybrid roll was designed based on analytical results. Experiments were conducted for measuring the performance of the developed hybrid roll.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.22-28
• /
• 2011

This paper presents an active roll motion control of a passenger vehicle. The roll controller is designed in the framework of $H_{\infty}$ control scheme based on the 3 DOF vehicle model taking into consideration parameter variations, which affect the roll dynamics, and unmodeled high frequency dynamics for robustness and performance. In order to investigate the feasibility of the active roll control system in a car, its performance is evaluated by simulation in a full vehicle model with nonlinear tire characteristics under various operating conditions. Finally, in order to enhance the performance in a transient region taking into account the limited bandwidth of the actuating module, a hybrid control strategy is presented.

• International Journal of Automotive Technology
• /
• v.3 no.3
• /
• pp.123-128
• /
• 2002

This paper presents the design of an active roll control system for a ground vehicle and an experimental study using an devised electric-actuating roll control system. Based on a three degree of freedom linear vehicle model, the controller is designed using lateral acceleration and rollrate feedback. In order to investigate the feasibility of an active control system, experimental work is carried out using a hardware-in-the-loop (Hil) setup which has been constructed by the devised electric-actuating system and the full vehicle model including tire characteristics. The performance is evaluated by an experiment using the Hil setup with limited bandwidth. Finally, in order to enhance the control performance in the transient region, a hybrid control strategy is proposed and evaluated.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.623-624
• /
• 2009

Here we report a photo polymerization-induced hybrid alignment of a nematic liquid crystal cell which can be applied for a roll to roll fabrication process. Predominant polymerization in the vicinity of UV incident front induced a diffusion of monomers toward front slide and anisotropic polymer network was formed parallel to the polarization direction of the UV light. This induced planar alignment of liquid crystals at the front slide. Simultaneously, homeotropic alignment was induced at the bottom slide as the polymers are phase-separated from a bottom slide.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1299-1300
• /
• 2013

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.629-630
• /
• 2013

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.418-420
• /
• 2009

The Authors have demonstrated high efficiency hybrid white organic light-emitting diodes (HWOLED) for reduced efficiency roll-off and color stability. It was shown that HWOLED fabricated in this study have the maximum luminance of 46 420 cd/$m^2$ at 8 V (turn-on voltage of 2.7 V), external quantum efficiency of 13.18%, power efficiency of 28.75 lm/W at 1 000 cd/$m^2$, and reduced efficiency roll-off of 2.7 times than control white device. The HWOLED also showed the stable color shift with $\Delta$Commission Internationale de I'Eclairage coordinates coordinates of ${\pm}$ (0.00, 0.00) from 100 to 10000 cd/$m^2$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.377-377
• /
• 2009

Currently, new and renewable energy come into the spotlight, such as solar energy, wind power, fuel cell, hybrid car etc., due to the energy resources is being depleted. In order to solve like this problem, we addressed the roll to roll printing machine for the thin film solar cell by using printing technology. For the this research, we archived concept design and verified propriety.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.104-112
• /
• 2017

In the sand casting process, the flow of liquid metal affects the quality of casting products and their die life. To determine the optimal bush part design process, this study performed various analyses using commercial finite element analysis S/W. The simulation focused on the molten metal behaviors during the mold filling and solidification stages of sand casting. This study aims to develop methods to reduce the cost and increase the tool life of the continuous hot zinc plating roll.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.665-666
• /
• 2011