• Bulletin of the Society of Naval Architects of Korea
• /
• v.6 no.1
• /
• pp.25-34
• /
• 1969

From viewpoints of over-all ship economy the straight framed V-bottom hull forms with chines are considered to be attractive even for usual commercial vessels, because increments of resistance over that of round hull forms, if any, can be well compensated with reduction in construction cost.[1] To investigate the influences of both prismatic coefficient and chine elevation on resistance performance, three models of straight-framed V-bottom hull forms which are similar to Prof. C. Ridgely-Nevitt's W-18, W-8, and W-20[2],[3] in size and hull form coefficients were tested at the SNU Ship Model Towing Tank for resistance measurements. They are of Cp=0.60, 0.65 and 0.70 and of ${\Delta}/(0.01L)^3=300$. Influence of variation of chine elevation on resistance performance were observed with the test results obtained at normal condition, and at the trimed by the stern by 2% and 4% of $L_{bp}$ at normal condition under same displacement. The hull form characteristics are shown in Table 1, and in Fig. 1, 2, 3, 4 and 5. The test results are shown in Fig 8, 9 and 10 in the form of Cr vs. $V/\sqrt{L}$ curves taking Cp as a parameter for normal condition, trim by the stern in 2% and 4% $L_{bp}$ at normal condition , respectively. Cr vs. $V/\sqrt{L}$ curves taking trim condition as a parameter are also shown in Fig 11, 12 and 13 for Cp=0.60 and 0.70, respectively. The best and the worst trim condition at given $V/\sqrt{L}$ in viewpoint of Cr are plotted for each Cp-value as shown in Fig 14, 15 and 16. From the above results the following conclusions are derived: (1) In general, the resistance performance of the straight-framed V-bottom hull forms are not inferior to those of round hull forms. At a certain range of $V/\sqrt{L}$ the former gives less resistance than the latter. (2) Regarding influences of Cp on Cr, it is observed that, at $V/\sqrt{L}$ less than about 0.925, the greater Cp-value gives the more increment of Cr, and that, at $V/\sqrt{L}$ greater than about 0.925 the smaller Cp-value gives the more increment of Cr. It is also noteworthy that the model of Cp=0.70 has remarkable hump on Cr vs. $V/\sqrt{L}$ curve between $V/\sqrt{L}=0.80$ and 0.90. (3) For higher speed within the test range, the chine elevation having the steeper slope around bow and the easier slope around amidship and stern, refered to watering, give the better results in resistance performance. (4) Assuming the chine elevations adopted for the tested models were not of the best, we would expect further improvement of resistance performance for such form. Hence, a systematic study on chine elevation is very disirable to prepare design data of general purpose for the such hull forms.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.2
• /
• pp.496-506
• /
• 2014

In this paper the scenario based optimization of the bulbous bow of the KRISO Container Ship (KCS) is presented. The optimization of the parametrically modeled vessel is based on a statistically developed operational profile generated from noon-to-noon reports of a comparable 3600 TEU container vessel and specific development functions representing the growth of global economy during the vessels service time. In order to consider uncertainties, statistical fluctuations are added. An analysis of these data lead to a number of most probable upcoming operating conditions (OC) the vessel will stay in the future. According to their respective likeliness an objective function for the evaluation of the optimal design variant of the vessel is derived and implemented within the parametrical optimization workbench FRIENDSHIP Framework. In the following this evaluation is done with respect to vessel's calculated effective power based on the usage of potential flow code. The evaluation shows, that the usage of scenarios within the optimization process has a strong influence on the hull form.

• Journal of Ocean Engineering and Technology
• /
• v.37 no.4
• /
• pp.129-136
• /
• 2023

To evaluate manoeuvring performance of merchant ships, the mathematical modeling group (MMG) or computational fluid dynamics (CFD) simulations are used. However, it is difficult to use the MMG to evaluate the manoeuvring performance of fishing vessels, thus research using CFD simulations is necessary. Also, since the course-changing and turning ability is crucial in fishing operations, a rudder design suitable for fishing vessels is necessary. This study designs a rudder using National Advisory Committee for Aeronautics (NACA) airfoil sections and evaluates its manoeuvring performance. A CFD model is used to evaluate the manoeuvring performance of the fishing vessel, and turning and zig-zag tests are conducted. The effectiveness of using CFD simulations based on Reynolds averaged Navier-Stokes equations to assess the manoeuvring performance of fishing vessels was validated. No significant difference was found in the manoeuvring performance for hull forms and rudder designs for course-changing ability. However, the original hull form showed superior turning performance. Among five rudders with varying aspect ratios and shapes, the rudder with 5.5% aspect ratio had the best turning performance. Regarding the rudder design for fishing vessels, NACA airfoil was employed, and a rudder aspect ratio of 5.5% based on the immersed hull side area is recommended.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.5
• /
• pp.387-392
• /
• 2017

There is a constant demand for hull variation related to ship design. Various input variables are generally given to achieve the objective functions assigned by each variation process. When dealing with geometric shapes accompanied by nonlinear operations during the variation process, vague relationships or uncertainties among input variables are commonly observed. Therefore, it is strongly recommended to identify those uncertainty factors in advance. A method to modify the shape of a closed hull form with a new area and a centroid had been introduced as a new process of hull variation. Since uncertainty between input variables still existed in the method, however, it was not easy for the user to enter the area and the corresponding centroid. To overcome this problem, a method is presented in this paper to provide the feasible region of centroids for a given area. By utilizing the concept and techniques used in the statistics such as the number of samples, probability, margin error, and level of confidence, this method generates the distribution of possible centroids along the regression curve. The result shows that the method helps the user to choose an appropriate input value following his or her design intention.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.4 no.3
• /
• pp.291-301
• /
• 2012

A scalar metric for the assessment of hull surface producibility was known to be useful in estimating the complexity of a hull form of ships or large offshore structures by looking at their shape. However, it could not serve as a comprehensive measuring tool due to its lack of important components of the hull form such as longitudinals, stiffeners, and web frames attached to the hull surface. To have a complete metric for cost estimation, these structural members must be included. In this paper, major inner structural members are considered by measuring the complexity of their geometric shape. The final scalar metric thus consists of the classes containing inner members with various curvature magnitudes as well as the classes containing curved plates with single and double curvature distribution. Those two distinct metrics are merged into a complete scalar metric that accounts for the total cost estimation of complex structural bodies.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.6
• /
• pp.674-680
• /
• 2013

As the range of marine leisure activity gradually expands to ocean-going, a habitable cruise boat has been getting the limelight. Advanced countries in the marine leisure industry in Europe and North America have already secured their competitiveness in designing and building cruise boats by elegant design, ergonomic structure and fuel efficiency through the adoption of light-weight hull materials. In contrast, mostly small power boats are developed and built in Korea, and GFRP take up the most of hull materials. This study inquired into the design and characteristics of a 50ft-class CFRP that ocean-going is possible. The hull-form of the CFRP cruise boast were analyzed to propose a hull form for the designed ship (MMU-C.B), and based on that, the design model of the MMU-C.B was built. Finally, the MMU-C.B's characteristics of the resistance performance and hull-planing were found by comparative reviews with the results of model tests of GFRP pleasure yachts.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.2
• /
• pp.134-140
• /
• 2011

The present paper deals with characteristics of resistance performance according to the variation of synthetic ice thickness and hull form. The resistance test has been conducted with pack ice condition in Pusan National University towing tank. Waterline angle has been chosen as a main parameter for the variation of hull form characteristics, which is the most important factor especially in icebreaking cargo vessel. The serial comparisons of resistance test have been done with the variation of hull form parameter as well as with the different thickness of synthetic ice. The different trend of resistance performances with increasing of waterline angle has been shown at each synthetic ice thickness. The present test results is expected to be confirmed by comparing the test results in ice tank in the near future.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.8 no.1
• /
• pp.1-16
• /
• 1971

Ship hulls obtained by the streamline tracing method usually have characteristically drooped keel lines at the bottom, and a flattening of these bottoms would contribute considerably in utilizing these analytically obtainable hull forms in practical usage. In this dissertation, the author deals with a study on the determination of a practical hull form by the streamline tracing method with a particular emphasis on the bottom flattening problem. Investigations are centered around the form and the terms of bottom doublet distribution. Several examples are computed by varying bottom doublet sheet systematically while the main side source distribution is kept the same. The following conclusions are obtained based on those computed results: after the strength of a bottom doublet sheet can be determined more easily and efficiently by employing the concept of a control plane. If the distance from the distributed plane of the bottom doublet sheet to the control plane is defined as the control distance, the strength of the bottom doublet sheet, the flatness of traced lines, and the increment of the beam length ratio by adding the bottom doublet sheet are all related to the control distance by linear equations near the design bottom. It is observed that a better result can be obtained by using a "line-sampling method" for ${\zeta}_K>2T/L$, and a "plane-sampling method" for ${\zeta}_K{\leq}2T/L$, provided that the check points are sampled in the range ${\xi}{\leq}0.7$.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.6
• /
• pp.1-6
• /
• 2013

A 25ft class fishing leisure boat is developed, and the resistance performances are investigated by a model test in a high-speed circulating water channel. The design speed of the developed ship is 25 knots using a 150 ps outboard engine. A catamanan type hull form using a planing section is adopted considering the Froude number and large deck area. The effect of a center body attached on the bottom of the cross deck is studied under various conditions. Wave patterns are observed to make clear the relationship between the resistance performance and the wave characteristics. The results show that the shape of the center body and the position of the chine line can have a strong effect on the resistance performance in a certain velocity range.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.2
• /
• pp.78-84
• /
• 2008

As a preliminary step to build a complete superyacht hull design program, the development of superyacht profile design system is introduced. The two-dimensional hull profile is decomposed into four local zones depending upon the functionality and connecting continuity of the profile. Characteristics of each zone are investigated and used to generate the model describing the geometric shape of zone using freeform curves. A set of design parameters is derived from the established geometric model. Generation and modification of a model are is by manipulating the chosen parameters. Four zones designed are integrated to form a final profile. An interactive design system performing all the modeling and modification processes is implemented using the graphic user interface system based an Microsoft Foundation Class and OpenCASCADE, a open graphic library. The shapes of the profiles generated by the developed design system are verified with those of built superyachts. The developed design system will be used for the construction of three-dimensional superyacht hull modeling system.