• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.1 s.145
• /
• pp.68-74
• /
• 2006

The welding distortion of a hull structure in the shipbuilding industry is inevitable at each assembly stage. This geometric inaccuracy caused by the welding distortion tends to preclude the introduction of automation and mechanization and needs the additional man-hours for the adjusting work at the following assembly stage. To overcome this problem, a distortion control method should be applied. For this purpose, it is necessary to develop an accurate prediction method which can explicitly account for the influence of various factors on the welding distortion. The validity of the prediction method must be also clarified through experiments. For the purpose of reducing the weld-induced bending deflection, this paper proposes the mechanical tensioning method (MTM) as the optimum distortion control method. The validity of this method has been substantiated by a number of numerical simulations and actual measurements.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.135-139
• /
• 2017

The main reason for heat accidents occurring at the after stern tube bearing (STB) is excessive local pressure caused by the deflection of the propulsion shaft due to propeller loads. The probability of a heat accident is increased by the low flexibility of the shaft system in very large crude oil carriers (VLCCs) as the engine power and shaft diameter increase and the distance decreases between the forward and after STBs. This study proposed shaft system with only an after STB and no forward STB for a flexibility acquisition method for a VLCC shaft system under hull deformation. A Hertzian contact condition was applied, which assumes a half-elliptical pressure distribution along the contact width for the calculation of the local squeeze pressure. The propeller loads, heat effect, and hull deflection under engine operating conditions are also considered. The results show that the required design criteria were satisfied by building a partial slope at the white metal, which is the material at the axial contact side in the after STB. This system could reduce building cost by simplification of the shaft system.

• Journal of Navigation and Port Research
• /
• v.29 no.6 s.102
• /
• pp.509-513
• /
• 2005

Ship maneuverability is mainly determined according to hull-propeller-rudder system of a ship and directly related to the ship safety during the operation in the ocean. Among hull-propeller-rudder system the rudder system had direct concern with the ship maneuverability and a special rudder has been recommended to improve the ship maneuverability. In this paper the study of flapped rudder's 2-dimensional section was accomplished Model tests had been carried out with different angles of attack of a main foil and flap's deflection angles to predict the performance of the flapped rudder and the 2 frame particle tracking method had been used to obtain the velocity distribution in the flow field during model tests. $Re=1.027{\times}10^4$ had been used during the whole experiments and measured results had been compared with each other.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.3
• /
• pp.53-60
• /
• 1997

Generally, a safety estimation based on the buckling strength is carried out to evaluate the strength of plate members in the design process of ship hull structures and more accurate and efficient tool for the buckling strength estimation of enormous plate members of ship structure is naturally demended for saving design process. While, in the reason that the design codes of classification societies do not consider the various effects or include some effects roughly, considerate safe side results are suggested occasionally. In this study, advanced buckling strength estimation system prepared various classification buckling evaluation codes and new evaluation code considering the effects of in-plane tension, plate boundary condition, lateral load & residual stress is developed using the window management system of engineering workstation. Additionally maximum deflection estimation formula is equipped for the increase of fabrication reliability of thin plate ship structure. From this evaluation system, more reliable buckling safety of plate panel will be guaranteed in the ship hull design stage. In order to expand the use of this system pc version system will be developed sooner or later.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.2
• /
• pp.270-287
• /
• 2015

According to the increase of the operating cost and material cost of a ship due to the change of international oil price, a demand for the lightening of the ship weight is being made from various parties such as shipping companies, ship owners, and shipyards. To satisfy such demand, many studies for a light ship are being made. As one of them, an optimal design method of an existing hull structure, that is, a method for lightening the ship weight based on the optimization technique was proposed in this study. For this, we selected a hatch cover of a bulk carrier as an optimization target and formulated an optimization problem in order to determine optimal principal dimensions of the hatch cover for lightening the bulk carrier. Some dimensions representing the shape of the hatch cover were selected as design variables and some design considerations related to the maximum stress, maximum deflection, and geometry of the hatch cover were selected as constraints. In addition, the minimization of the weight of the hatch cover was selected as an objective function. To solve this optimization problem, we developed an optimization program based on the Sequential Quadratic Programming (SQP) using C++ programming language. To evaluate the applicability of the developed program, it was applied to a problem for finding optimal principal dimensions of the hatch cover of a deadweight 180,000 ton bulk carrier. The result shows that the developed program can decrease the hatch cover's weight by about 8.5%. Thus, this study will be able to contribute to make energy saving and environment-friendly ship in shipyard.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.10 no.2 s.21
• /
• pp.41-47
• /
• 2004

Plate has cutout inner bottom and girder and Door etc. in hull construction absence is used much, and this is strength in case must be situated, but establish in region that high stress interacts sometimes fatally in region that there is no big problem usually by purpose of weight reduction, a person and freight movement, piping etc.. Because cutout‘s existence is positioning in this place, and, elastic bucking strength by load causes large effect in ultimate strength. Therefore, perforated plate elastic bucking strength and ultimate strength is one of important design criteria to decide structural elements size at early structure design step of a ship. Therefore, we need reasonable & reliable design formula for elastic bucking strength of the perforated plate. The author computed numerically ultimate strength change about several aspect ratios, cutout dimension, and plate thickness by using ANSYS Finite element analysis code based on finite element method in this paper.

• Proceedings of KOSOMES biannual meeting
• /
• 2004.11a
• /
• pp.129-135
• /
• 2004

Plate has cutout inner bottom and girder and floor etc in hull construction absence is used much, and this is strength in case must be situated, but establish in region that high stress interacts sometimes fatally in region that there is no big problem usually by purpose of weight reduction, a person and change of freight, piping etc. Because cutout's existence gnaws in this place, and, elastic budding strength by load rouses large effect in ultimate strength. Therefore, perforated plate elastic budding strength and ultimate strength is one of important design criteria which must examine when decide structural elements size at early structure design step if ship. Therefore, and, reasonable elastic budding strength about perforated plate need design ultimate strength. Calculated ultimate strength change several aspect ratioes and cutout's dimension, and thickness in this investigation. Used program applied ANSYS F.E.M code based on finite element method

• Bulletin of the Society of Naval Architects of Korea
• /
• v.13 no.1
• /
• pp.17-23
• /
• 1976

Some methods of analysis of rectangular plates under distributed load of various intensity with interior supports are presented herein. Analysis of many structures such as bottom, side shell, and deck plate of ship hull and flat slab, with or without internal supports, Floor systems of bridges, included crthotropic bridges is a problem of plate with elastic supports or continuous edges. When the four edges of rectangular plate is simply supported, the double Fourier series solution developed by Navier can represent an exact result of this problem. If two opposite edges are simply supported, Levy's method is available to give an "exact" solution. When the loading condition and supporting condition of a plate does not fall into these cases, no simple analytic method seems to be feasible. Analysis of a simply supported rectangular plate under irregularly distributed loads of various intensity with internal supports is carried out by applying Navier solution well as the "Principle of Superposition." Finite difference technique is used to solve plates under irregularly distributed loads of various intensity with internal supports and with various boundary conditions. When finite difference technique is applied to the Lagrange's plate bending equation, any of fourth order derivative term in this equation produces at least five pivotal points leading to some troubles when the resulting linear algebraic equations are to be solved. This problem was solved by reducing the order of the derivatives to two: the fourth order partial differential equation with one dependent variable, namely deflection, is changed to an equivalent pair of second order partial differential equations with two dependent variables. Finite difference technique is then applied to transform these equations to a set of simultaneous linear algebraic equations. Principle of Superposition is then applied to handle the problems caused by concentrated loads and interior supports. This method can be used for the cases of plates under irregularly distributed loads of various intensity with arbitrary conditions such as elastic supports, or continuous edges with or without interior supports, and this method can also be solve the influence values of deflection, moment and etc. at arbitrary position of plates under the live load.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.13 no.4
• /
• pp.19-24
• /
• 1976

Some method of analysis of rectangular plates under distributed load of various intensity with all edges built in are presented in. Analysis of many structures such as bottom, side shell, and deck plate of ship hull, and flat slab, deck systems of bridges is a problem of plate with continuous supports or clamped edges. When the four edges of rectangular plate is simply supported, the double fourier series solution developed by Navier can represent an exact result of this problem. If two opposite edges are simply supported, Levy's method is available to give an "exact" solution. When the loading condition and boundary condition of a plate does not fall into these cases, no simple analytic method seems to be feasible. Analysis of a plate under distributed loads of various intensity with all edges built in is carried out by applying Navier solution and Levy's method as well as "Principle of Superposition" In discussing this problem we start with the solution of the problem for a simply supported rectangular plate and superpose on the deflection of such a plate the deflections of the plate by slopes distributed along the all edges. These slopes we adjust in such a manner as to satisfy the condition of no rotation at the boundary of the clamped plate. This method can be applied for the cases of plates under irregularly distributed loads of various intensity with two opposite edges simply supported and the other two edges clamped and all edges simply supported and this method can also be used to solve the influence values of deflection, moment and etc. at arbitrary position of plates under the live load.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.2
• /
• pp.104-113
• /
• 1998

The line heating method is a popular technique used to form ship hull in shipyards. In order to promote shipbuilding productivity, some researchers have made progress in their studies on automatic fabrication system for plate forming. These researches have, however, focused on heat-induced plate deformation with particular mechanical modelings, and do not yet propose the heating paths applicable to actual plate forming process. In this paper, a new algorithm to determine heating lines is developed to simulate the line heating process. The important feature of this algorithm is that it calculates principal curvatures of deflection difference surface which represents difference between target surface and surface in fabrication. Several trials to typical surface types show its usefulness and good applicability to tactical use.