• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.04a
• /
• pp.496-503
• /
• 2003

Recently, the buckling is easy to happen a thin plate and High Tensile Steel is used at the structure so that it is wide. Especially, the buckling is becoming important design criteria in the ship structure to use especially the High Tensile Steel. Consequently, it is important that we grasp the conduct after the buckling behaviour accurately at the stability of the body of ship structure. In this study, examined closely about conduct and secondary buckling after initial buckling of thin plate structure which receive compressive load according to various kinds aspect ratio under simply supported condition that make by buckling formula in each payment in advance rule to place which is representative construction of hull. Analysis method is F.E.M by ANSYS and complicated nonlinear behaviour to analyze such as secondary buckling.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.201-204
• /
• 2006

A three-dimensional finite element (FEM) model has been developed to simulate the deformation due to bead on plate welding of curved plates with curvature in the weld direction. By using traditional method such as thermal-elastic-plastic FEM, the weld-induced deformation can be predicted accurately. However, this method is not practical approach to analyze the deformation of large and complex structures such as ship hull structures in view of time and cost. This study is classified from the aspect of equivalent load based on inherent strain near the weld line. Therefore, the residual deformation can be simply computed by elastic analysis. Further more, a practical solution is proposed to consider the contact between the plate and the positioning jig by judging the reaction forces of the jig at calculation step and the effect of the longitudinal curvature is closely considered.

• Journal of Welding and Joining
• /
• v.32 no.1
• /
• pp.47-52
• /
• 2014

Due to of high intensity, lower noise and easy controllability of the heat, induction heating system became well known. Induction heating method has been suggested as substitute for the gas heat source and adopted in the automation of curved hull forming system. In this study, an investigation was accomplished to find the effects on the change of material properties when the induction heating was applied on the mild steel plate. Plates were heated using weaving method to get sufficiently heat affected zone and then cooled with water or in the air. The mechanical properties of the heated plate were evaluated. As results, the tensile test, impact test and microstructures satisfied the class rule.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.732-737
• /
• 2003

Recently, the buckling is easy to happen a thin plate and High Tensile Steel is used at the structure so that it is wide. Especially, the buckling is becoming important design criteria in the ship structure to use especially the High Tensile Steel. Consequently, it is important that we grasp the conduct after the buckling behaviour accurately at the stability of the body of ship structure. In this study, examined closely about conduct and secondary buckling after initial buckling of thin plate structure which receive compressive load according to various kinds aspect ratio under simply supported condition that make by buckling formula in each payment in advance rule to place which is representative construction of hull. Analysis method is F.E.M by ANSYS and complicated nonlinear behaviour to analyze such as secondary buckling.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.348-356
• /
• 2003

Recently, the buckling is easy to happen a thin plate and High Tensile Steel is used at the steel structure and marine structure so that it is wide. Especially, the post-buckling is becoming important design criteria in the ship structure to use especially the High Tensile Steel. Consequently, it is important that we grasp the conduct post-buckling behaviour accurately at the stability of the ship structure or marine structure. In this study, examined closely about conduct and snap-through behaviour after initial buckling of thin plate structure which apply compressive load according to various kinds initial deflection shape under all edges simply supported condition that make by buckling formula in each payment in advance rule to place which is representative construction of hull. Analysis method is F.E.M in used ANSYS program and complicated nonlinear behaviour to analyze such as secondary buckling with snap-through behaviour. Nonlinear buckling control is applied between newton-raphson method and arc-length method in this study

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.419-423
• /
• 2008

This study is regarding to the Print System recording the information for the treatment on vessel steel plate in the process Ship Drying on moving without stopping. The print head accepts the locating information of moving steel plate sensored in sensor and It is aimed for the construction of facilities that the print head prints the information of maps, letters and signals for treatment on Steel plate surface on moving.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.22 no.2
• /
• pp.12-26
• /
• 1985

This paper describes the experimental method to predict the propeller induced fluctuating pressure on the hull surface. Cavitations of the three model propellers with varying degree of skews, $0^{\circ},\;36^{\circ}\;and\;72^{\circ}$, were observed and the fluctuating pressure induced by the cavitating propellers in the flat plate above these propellers were measured simultaneously at 9 points in the wake field generated by the wire-mesh screens. Another model propeller designed for the dummy model ship was tested in a similar way behind the dummy model ship. The effects of skew variation on the cavitation patterns and fluctuating pressures were illustrated, and the influence of tip-clearances on the fluctuating pressures was also demonstrated. As a result, it is shown that the level of fluctuating pressure and cavity extent could be controlled to some extent by introducing the skews and tip clearances.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.13 no.1
• /
• pp.25-34
• /
• 1976

Analytical solutions for the transient temperature and quasi-static thermal stresses which arise in thin plates subjected to an instantaneous point source of heat have been investigated. And the solutions have been extended to the case of a moving source of heat with the aid of the Duhamel's superposition integral. For finite disk an experiment was conducted, the measured temperature histories show a good agreement with the theoretical temperature histories, And the histories of thermal stresses show a good qualitative agreement with the physical phenomena. And also we can find out that the maximum temperature and thermal stresses and their location can be estimated by using the solutions for infinite plates instead of the solutions for a finite plate. The solutions can be used for the problems such as a welding or line heating in a hull construction.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.1
• /
• pp.48-58
• /
• 2002

There is a purpose of this study for the proposal of the optimum technique utilized for the vibration design initial step. The stiffened plate structure for the ship hull is made for analysis model. To begin with, dynamic characteristics of stiffened plate structure is analysed using FEM. Main vibrational mode of the structure is decided in the analytical result of FEM. The simplified equation on the natural frequency of the main vibrational mode is induced. Next, sensitivity analysis is carried out using the simplified equation, and rate of change of dynamic characteristics is calculated. Then, amount of design variable is calculated using this sensitivity value and optimum structural modification method. The change of natural frequency is made to be an objective function. Thickness of panel, cross section moment of stiffener and girder become a design variable. The validity of the optimization method using simplified equation is examined. It is shown that the result effective in the optimum modification for natural frequency of the stiffened plate structure.

• International Journal of Ocean System Engineering
• /
• v.1 no.1
• /
• pp.46-51
• /
• 2011

In a line heating process for hull forming, the phase of the steel transforms from austenite to martensite, bainite, ferrite, or pearlite depending on the actual speed of cooling following line heating. In order to simulate the water cooling process widely used in shipyards, a heat transfer analysis on the effects of impinging water jet, film boiling, and radiation was performed. From the above simulation it was possible to obtain the actual speed of cooling and volume percentage of each phase in the inherent strain region of a line heated steel plate. Based on the material properties calculated from the volume percentage of each phase, it should be possible to predict the plate deformations due to line heating with better precision. Compared to the line heating experimental results, the simulated water cooling process method was verified to improve the predictability of the plate deformation due to line heating.