• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.166-173
• /
• 2002

The wheel bearing hub unit is developed type of wheel bearing unified with the hub parts. It has advantage of reducing the weight and the number of components. And, it also improves uniformity of manufacturing quality, In order to design the wheel bearing hub units, many techniques are used such as load analysis, structure analysis and bearing characteristics analysis and so forth. These techniques need highly accurate load conditions founded on service conditions. In this study, to design the wheel bearing hub units used widespread in passenger cars, the service load was measured through driving tests on the public roads and in the special events. The public roads are classified into highway, intercity road, rural road, urban road, and unpaved road so as to know what the characteristics of the road loads are. The results of the tests showed that the wheel force was relative to the lateral acceleration, and also could be calculated from the lateral acceleration. The lateral acceleration was measured from 0.0G to 0.6G in general driving on the public roads, with different distributions in each road type. In special events, the maximum lateral acceleration was measured from 0.8G to 1.3G.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.363-368
• /
• 2002

An automobile hub is composed of a hollow cylindrical part with inner and outer diameters. These hub diameters must be precise, as any irregularities in them (diameters) can influence/degrade the motion of an automobile with this problem. Highly accurate and reliable hub inner and outer diameters measurement systems are therefore required for inspection of the diameters. In this research, an automobile hub inner and outer diameters measurement system has been developed and tested. The system consists of measuring heads with LVDT sensors, and associated software for automatic measurement and calibration of the diameters and the sensors respectively. The system has been evaluated in comparison with an existing measurement system, and the following outcomes have been achieved; .Improved and guaranteed quality and reliability .Increased productivity and cost reduction. These results prove the system developed in this research to be suitable for automobile hub inspection.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.347-350
• /
• 1998

본 논문에서는 최근 광대역 무선 가입자망으로 각광받고 있는 LMDS(Local Multipoint distribution Service)시스템에서 Head-End 의 AIU(Air Interface Unit)와 HUB 사이의 거리에 따른 전송지연 시간과 HUB 와 가입자 장치(CPE:Customer Premises Equipment)내의 NIU(Network Interface Unit)간의 전송 지연 시간에 의하여 서비스 반경이 제한되어 지는 것에 관하여 살펴보고 적절한 서비스 반경에 대하여 제안하였다.

• 전기전자학회논문지
• /
• 제21권2호
• /
• pp.158-161
• /
• 2017

본 논문에서는 원자력 및 핵의학 분야용 Total RMS(Radiation Monitoring System)를 제안한다. 제안하는 시스템은 Stack Monitor, Area Monitor, Water(Liquid) Monitor 등을 하나의 시스템으로 확장 및 제어할 수 있는 장비로 각 방사선 검출기에서 측정된 신호를 통합 모니터링 할 수 있다. 제안하는 시스템은 해당 방사선을 검출하는 Sensor Module, 방사선 검출 위치에 인접한 곳에서 방사선량을 디스플레이 하는 Display Unit, 검출된 방사선량이 위험 수준에 도달시 경보를 알리는 Alarm Unit, 각 모니터링에서 측정된 방사선량들을 취합하고 저장하여 원격 감시 시스템에 내용을 전달하는 Main Hub, 원격지에서 측정된 방사선량 상태를 일목요연하게 디스플레이 하는 RMS Monitoring Unit 등으로 구성된다. 제안된 원자력 및 핵의학 분야용 Total RMS의 성능을 평가하기 위하여 공인시험기관에서 실험한 결과, 측정 불확도가 8.5%이하로 측정되어 국제 표준인 ${\pm}15%$ 이하에서 정상동작 됨이 확인되었다.

• 한국경제지리학회지
• /
• 제13권2호
• /
• pp.219-233
• /
• 2010

본 연구는 기업 단위가 아닌 산, 학, 연 네트워크로서의 산업클러스터 단위에서 지식경영을 어떻게 도입, 이용할 수 있는가라는 연구 과제에 초점을 두는 것이다. 이를 위해 다양한 국내외 사례 연구를 통해 개별 기업이 아닌 산업클러스터에서 새로운 개념의 지식경영이 필요한 혁신 환경을 파악해 보았다. 또한 사례연구를 토대로 산업클러스터 단위에서의 지 식경영체계의 특성을 파악해 보았으며 통합적, 체계적 지식경영활동의 지원을 위한 산업클러스터에서의 실험적 지식경영시스템으로 '지식허브(Knowledge Hub)'의 구축을 제안해 보았다. 지식허브는 산업별, 지역간 연계를 통해 확장된 개념의 혁신체계에 대한 지원 역할이 가능하도록 개발될 필요가 있다. 본 연구의 결과는 특히 산, 학, 연 등 산업클러스터 구성 요소의 입지가 부족한 편인 지방 산업클러스터의 효과적 혁신 촉진을 위한 대안이 될 수 있을 것이다.

• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.72-77
• /
• 2011

In this paper, we propose effective diagnosis algorithm for hub bearing fault in driving vehicle using acceleration signal and wheel speed signal measured in hub bearing unit or knuckle. This algorithm consists of differential, envelope and power spectrum method. We developed diagnosis system for realizing proposed algorithm. This system consists of input device including acceleration sensor and wheel speed sensor, calculation device using Digital Signal Processor (DSP) and display device using Personal Digital Assistant (PDA). Using this diagnosis system, a driver can see hub bearing fault(flaking) from the vibration in driving vehicle. With early repairing, he can keep good ride feeling and prevent accident of vehicle resulting from hub bearing fault.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2013년도 추계학술대회
• /
• pp.612-615
• /
• 2013

허브(hub) BLDC(Brushless Direct Current) 전동기란 아우터로터 타입 고효율 전동기로 다극의 영구자석으로 이루어진 회전자가 바퀴의 구동축이 되는 직접구동용 모터를 말하며, 휠인모터라고도 불린다. 본 연구에서는 허브모터를 구동축으로 갖는 2륜 또는 3륜 구동체를 구동하기 위한 BLDC 허브모터 속도 제어기를 PIC 마이크로 컨트롤러를 이용하여 설계한다. 구동기는 6 개의 독립된 MOSFET 스위칭소자를 사용하여 구성하며, 게이트 구동회로는 직접 설계하여 경제성을 높인다.

• 한국유체기계학회 논문집
• /
• 제13권6호
• /
• pp.30-35
• /
• 2010

The aerodynamic performance of axial flow fans for outdoor unit of air-conditioner is investigated by numerical and experimental approaches in this study. The pressure drop and volumetric flow rate are compared each other in several different conditions and fan speeds. It is shown that the predicted fan performances are quite well matched with the experimental results. It is also shown that the curvature of the fan arc and hub height have significant influences on the flow distribution after hub. By the results of this study, it can be suggested that several ways to improve the aerodynamic performance of the axial flow fan can be found using the numerical analysis.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.265-268
• /
• 2006

Performed fatigue strength analysis for Hub to get the targeted service life of 20 years. ANSYS is used to analysis. The major structure of bearing which connect the hub and blades is modeled using the element of LINK10. To represent the stiffness of LINK10 element, initial strain and diameter of LINK10 element is applied. Prior to calculating the fatigue damages, the influence matrix is extracted from the unit loads. The target service life of 20 years is achieved from the Analysis results.

• 한국정밀공학회지
• /
• 제19권12호
• /
• pp.142-149
• /
• 2002

In this paper, the metal forming process is caused of rise of the unit cost of production in increase of the lead-time and cost because of manufacturing final product through a few the number of processes. Flow control complex forming is proposed to put into formulation in order to apply cold forging from conventional approximate similarity theory, and the forming loads of the real material(AISI 1008) can be calculated by put at the new similarity formula the load by plasticine model material experiment through hub clutch. In order to reduce lead-time and cost the technology is used to manufacture with lower die of this product. By the application synthetic resin as the raw material, it is have the merit such short lead-time, low cost, good surface finish etc., as compared with the machine work.