• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.5-9
• /
• 2010

In the paper, the dynamic characteristics obtained from hot-firing tests of 1/2.5-scale thrust chamber for 75 tonf-class liquid rocket engine were described. To investigate the dynamic characteristics by engine start transient period and chamber pressure variation, hot-firing tests were performed in the chamber pressures of 30 bar and 60 bar. According to these variations, combustion stability in the combustion chamber was examined.

• International Journal of Aerospace System Engineering
• /
• v.9 no.2
• /
• pp.1-9
• /
• 2022

The NEA release mechanism is used to provide restraint and release functions with low shock for critical deployment operations on solar arrays after launch. The GK3 solar array consists of 2 wings and 6 hold down points per panel. The NEA SSD9103S1 is a part of the GK3 solar array hold-down and release mechanism. Each NEA unit is equipped with two Z-diodes which provide power to a NEA unit connected in series after actuation of the fuse wire. This paper presents the hot firing test results of a quadrature NEA SSD9103S1 configuration. One output powers a maximum of 4 NEA SSD9103S1 units simultaneously. The necessary actuation pulse duration has been determined to meet margin requirement for thermal energy of minimum 4. Actuation thermal energy difference is about 6.6% between each half of two fired serial NEAs. Thermal energy margin at worst case is minimum 5.9 in case of an actuation pulse duration of 500 ms. Two series Zener impedance depend on current applied has been characterized by an additional actuation after all fuse wires are open circuit. Total number of actuation commands to the GK3 NEA unit reduce drastically from 24 in case of single NEA configuration down to 8 in case of parallel and quadrature NEA configurations. It can be accommodated by the existing HP2U Pyro design without any impact.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.407-412
• /
• 2006

Most of the monopropellant thrusters use catalyst for decomposing hydrazine. The thruster lifetime is determined mainly by catalyst lifetime, which can be investigated by firing tests. For the development of hydrazine decomposition catalyst, Hot-fire test to verify long-life performance of catalyst is required. This study describes the development of test equipment for long duration hot-firing and test/evaluation plan.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.603-607
• /
• 2009

A Ni/Cr plating process has been developed for applying to inner wall of liquid rocket engine(LRE) thrust chamber. Ni plating conditions were selected through thermal shock test and endurance verification of the plating layers was performed through hot firing test of a subscale thrust chamber with Ni/Cr plating. Test results showed that a crack or separation of the plating layers was not found. Judging from the results, Ni/Cr plating could be applied to LRE thrust chamber as a substitute of air plasma sprayed ceramic coating which is presently being used.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.573-576
• /
• 2004

KARI is achieving the KSLV program according to National Space Technology Development Program. In this paper, the authors are intended to introduce the Integrated Power Plant (abb. IPP) test facility which will be constructed for the variety of tests on KSLV program. IPP test facility refers to comprehensive testing equipment for liquid rocket launch vehicle. Using this facility, KARl can verify the adaptiveness of parts and subsystems for launch vehicle and finally can qualify the system characteristics of launch vehicle doing kinds of test including hot firing test. Using this facility, KARI can simulate the vehicle launching circumstances and it make to predict the performance of launch vehicle when its flight test.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.2
• /
• pp.44-53
• /
• 2003

A vertical hot-firing test facility was established to carry out the IPPT(Integrated Propulsion Performance Test) and SQT(Stage Qualification Test) of KSR-III(Korea Sounding Rocket-III). The components for actual launcher were mostly used, hence these tests were carried out under the condition of relatively lower safety margin. To perform hot-firing tests with the maximum safety, an engine emergency blockage system was investigated and applied. An emergency blockage system using combustion chamber pressures and acceleration signals was set up to monitor ignition delay and fail, flame out, propellant feeding status, unstable combustion and excessive structural vibration. With such a system, the test safety could be secured by rapid judgement and follow-up measures, which made IPPT and SQT be safely completed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.5
• /
• pp.22-30
• /
• 2015

A gas generator which generates turbine driving gas by burning a part of propellants is used in an open cycle liquid rocket engine and as a main component of an open cycle liquid rocket engine autonomous hot firing tests are required to investigate the combustion performance and characteristics of the gas generator. However, since the combustion gas generated by a gas generator is choked at the turbine nozzle in the turbine manifold, it is necessary to consider the internal volume of turbine manifold as well as that of the gas generator for correct investigation of the combustion performance, characteristics, and acoustic characteristics of the gas generator. Therefore, in the paper hot firing test results of a gas generator with a turbine manifold simulator are described and characteristic prediction using the autonomous test of a gas generator is explained.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.49-56
• /
• 2005

Hot firing performance test of hydrazine decomposition catalyst used for monopropellant thruster of the satellite and the launch vehicle was performed. Test equipment for catalyst test was developed in collaboration with Hanwha Corp., reaction delay time, catalyst activity and granule stability of the catalyst firing performance were measured and analyzed with the equipment. In addition, the current development of prototype catalyst is introduced.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.292-295
• /
• 2004

Firing performance test of hydrazine decomposition catalyst which is used in mono-propellant thruster of satellite and launcher was peformed. Equipment for catalyst test was developed and with this equipment reaction delay time, catalyst activity, granule stability of the catalyst firing performance was measured and analyzed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.336-339
• /
• 2011

Hot-fire test facility is one of the most important infrastructure for thruster development and evaluation. During the past three years, Korea Aerospace Research Institute (KARI) and Hanwha Corporation have successfully performed the construction of hot-fire test facility for medium-scale monopellant thruster to the maximum 200N thrust level. In general, thruster hot-firing test should be performed in vacuum conditions to simulate space environment. The hot-fire test facility is divided into three subsystems, vacuum system, propellant supply system and data measurement & control system. The goal of this facility is to extend the capability from small thruster for satellite mission to medium-scale thruster for launch vehicle and lunar mission. In this paper, the progress and overview for thruster hot-fire test facility was introduced and test results were also presented.