• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.115-115
• /
• 2011

Biodiesel (BD) was made from animal-fats reacting with methanol and potassium hydroxide in the laboratory. The biodiesel made in the laboratory was sent to K-petro, the government agency, to inspect the quality of animal-fats biodiesel, of which generally the quality was acceptable for heating oil for agricultural hot air heater. Kinematic viscosity and calorific values of the biodiesels were measured. BD20(K), kerosene based biodiesel, showed 18cSt at $-20^{\circ}C$. It seems that BD100 can not be suitable for heating fuel under some temperature. As BD content increased calorific value decreased, up to 40,000J/g for 100% BD, while light oil calorific value was 45,567J/g, showing difference of 5,567J/g, about 12% difference. Several different fuels, BD20, BD50, BD100 and light oil, were prepared and tested for fuel combustion qualities for agricultural hot air heater and their combustion performances were compared and analyzed. Flame dimensions of biodiesels and light oil were almost same shape at the same combustion condition in the burner of the hot air heater. Generally $CO_2$ amounts of BDs are greater than light oil. But,the differences are so small that it is hard to tell there was significant difference existed between the BDs combustion and light oil.

• Journal of Biosystems Engineering
• /
• 제33권2호
• /
• pp.124-129
• /
• 2008

In this study, fuel qualities including kinematic viscosity and pour point in the various temperature, calorific value and combustion characteristics of two biodiesels based on the soybean and waste oil blended with light oil were investigated and discussed in order to figure out to confirm fuel compatibility taking the place of light oil in the hot air heater or boiler. As biodiesel content ratio increased calorific value of biodiesel decreased, and the difference was 13% between 100%-biodiesel and light oil. In general, pour points of the biodiesels were higher than light oil, and as biodiesel content ratio increased pour point increased. About 15 cSt was the pour point of biodiesels and light oil, which occurred at 3 to $4^{\circ}C$ in the biodiesels and $-25^{\circ}C$ in the light oil. Flame dimensions of biodiesels and light oil were almost same at the same combustion condition in the burner of the hot air heater. CO concentrations in the exhaustion gas were far lower than those of the light oil. Though pour point of biodiesel is a little inferior to light oil, still biodiesel can be an alternative fuel substituting for light oil in combustion system without much modifying the current oil combustion mechanism.

• Journal of Biosystems Engineering
• /
• 제37권5호
• /
• pp.296-301
• /
• 2012

Purpose: Combustion and fuel qualities of the animal-fats biodiesel as a heating fuel for agricultural hot air heater were studied. Methods: Biodiesel (BD) was made from animal-fats by reacting with methanol and potassium hydroxide in the laboratory. The biodiesel made in the laboratory was tested for fuel and combustion qualities. Results: The kinematic viscosity and the calorific values of the biodiesels were measured. Kerosene based biodiesel, BD20 (K) showed 18 cSt at $-20^{\circ}C$. It seemed that BD100 was not suitable for a heating fuel under some temperature. As BD content increased, the calorific value decreased up to 40,000 J/g for BD100, while the calorific value of light oil was 45,567 J/g showing difference of 5,567 J/g, about 12% difference. Several different fuels including BD20 (biodiesel 20% + light oil 80%), BD50 (biodiesel 50% + light oil 50%), BD100 (biodiesel 100%), and light oil were tested for fuel combustion qualities for agricultural hot air heater, and their combustion performances were compared and analyzed. Flame dimensions of biodiesels and light oils were almost the same shape at the same combustion condition. Generally, the $CO_2$ amounts of BDs were greater than light oil. However, in this study the differences were minor, so there was no significant difference existed between the BDs combustion and light oil. Conclusions: It seemed that quality was good for heating oil for agricultural hot air heater because of showing no barriers for continuous combustion and proper exhaust gas temperature and $CO_2$ amount discharged. But, for fuel fluidity for higher BD content fuel could be a detrimental problem in situations where the outdoor temperature is lowered. As BD content increased, calorific value decreased up to 40,000 J/g for BD100. Calorific value difference between BD20 and light oil was about 1,360 J/g.

• 한국기계기술학회지
• /
• 제13권3호
• /
• pp.107-111
• /
• 2011

This carbon nano heating system was consisted of power supply equipment, a carbon fiber and a stainless flexible hose. carbon nano heating system was manufactured by carbon fiber of a power capacity 30kw/h and light-oil hot air heater in control plot was the heating capacity 30,000kcal/h, As the result, Temperature difference due to carbon nano heating system and hot air heater in greenhouse showed that air temperature at experimental greenhouse, comparison greenhouse were $14.8^{\circ}C$, $13.4^{\circ}C$ respectively. It was found that carbon nano heating system and light-oil hot air heater heating cost were 1,095,740won, 2,683,628won. therefore as heating cost saving 60%. Yield of tomatoes cultured in greenhouse using carbon nano heating pipe was 4% inclease. Economic analysis comparison between the carbon nano heating pipe and the hot air heater in greenhouse were 41% respectively.

• Journal of Biosystems Engineering
• /
• 제34권5호
• /
• pp.363-370
• /
• 2009

Hot air heater with light oil combustion is used as the most common heater for greenhouse heating in the winter season. Hot air heaters of 256,246 units have been supplied as main greenhouse heating equipment until 2008 and greenhouse heating cost has reached to 620 billions won in Korea. In order to improve the thermal efficiency of the hot air heater and to reduce the expenses for greenhouse heating, prototype hot air heater was manufactured and tested in this experiment. The heat exchanger of tested prototype hot air heater was circular and hexagonal pipe type and inline and stagger arrangement type. Capacity of the heating was 43,062 kJ/h and total heat transfer area of the heat exchanger was $10.728\;m^2$. According to the performance test, it could supply heat of 38,240 to 35,100 kJ/h depending on the fan motor speed of 1,740~1,220 rpm, respectively. Thermal efficiency of hot air heater was 87.0% to 80.8% in the same conditions. As a result, thermal efficiency of hot air heater with hexagonal pipe-stagger arrangement heat exchanger developed in this study was higher 10.2% than that of conventional hot air heater and heating energy saving rate of 14.3% increased.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.126-132
• /
• 1996

A laboratory scale hot strip rolling wear simulator(HRWS) was developed for the purpose of investigating the tribological phenomena occurred in production hot strip rolling mills. The HRWS' main parts are the electric heater, the mechanical descaler, tandem type 2-4Hi rolling mill stands, the cooling chamber, the tension controller and coiler. By simulating the tribelogical phenomena in rolling process at laboratory, wear patterns, cracks, cat-ear wear, black film, effect of hot rolling oil lubrication, etc. were reproduced, and discussed on the performace of simulator.

• 대한안전경영과학회지
• /
• 제19권3호
• /
• pp.1-9
• /
• 2017

In the industrial field, various type of fuel have been used for product processing facilities. Recent for 10 years, the usage of natural gas (NG) was gradually increased. Because it has many merits; clean fuel, no transportation, storage facility and so on. There are common safety concept that strict explosion protection approaches are needed for facilities where explosive materials such as flammable liquid, vapor and gases exist. But some has an optimistic point of view that the lighter than air gases such as NG disperse rapidly, hence do not form explosion environment upon release into the atmosphere, many parts has a conventional safety point of view that those gases are also inflammable gases, hence can form explosion environment although the extent is limited and present. In this paper, the heating equipments (Hot Oil Heater) was reviewed and some risk management measures were proposed. These measures include hazardous area classification and explosion-proof provisions of electric apparatus, an early gas leak detection and isolation, ventilation system reliability, emergency response plan and training and so on. This study calculates Hazardous Area Classification using the hypothetical volume in the KS C IEC code.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2001년도 하계 학술대회 논문집
• /
• pp.136-141
• /
• 2001

• Journal of Biosystems Engineering
• /
• 제26권5호
• /
• pp.441-448
• /
• 2001

Hot air heater with light oil combustion is used as the most common heater for greenhouse heating in the winter season. However, exhaust gas heat discharged to atmosphere through chimney reaches up to 10~20% of total heat capacity of the oil burred. In order to recover the heat of this exhaust gas and to use for greenhouse heating, the heat pipe type exhaust heat recovery system was manufactured and tested in this experiment. The system consisted of a heat exchanger made of heat pipes, ø15.88${\times}$600mm located in the rectangular box of 675(L)${\times}$425(W)${\times}$370(H)mm, an air suction fan and air ducts. The number of heat pipe was 60, calculated considering the heat exchange amount between exhaust gas and air and heat transfer capacity of a heat pipe. The working fluid of heat pipe was acetone because acetone is known for its excellent heat transfer capacity. The system was attached to the exhaust gas path. According to the performance test it could recover 53,809 to 74,613kJ/h depending on the inlet air temperature of 12 to -12˚at air flow rate of 1.100㎥/h. The temperature of the exhaust gas left the heat exchanger dropped to 100$^{\circ}C$ from 270$^{\circ}C$ after the heat exchange between the suction air and the exhaust gas.

• 생물환경조절학회지
• /
• 제26권4호
• /
• pp.324-332
• /
• 2017

본 연구에서는 서로 다른 열전달 특성을 가진 탄소섬유 전기발열체와 경유온풍난방기가 온실 내부의 온습도, 에너지소비, 작물생육 등에 미치는 영향을 분석하기 위해 오이 재배 단동온실에 대한 난방 비교시험을 수행하였다. 전기발열체 온실에서 난방용량이 온실 환경과 난방기 운전에 미치는 영향을 분석하기 위해 온실에 6, 9, 16kW의 전력을 각각 공급한 결과 전기발열체 ON-OFF 주기는 각각 9, 11, 15회로 비례하여 증가하였으며 온실내부 평균온도는 각각 15.2, 15.3, $15.6^{\circ}C$, 평균상대습도는 84, 81, 76%로 나타나 난방 용량이 클수록 온실내부 온도는 높고, 상대습도는 낮게 나타났다. 또한 6, 9kW 가동 시 하부온도가 상부보다 $0.1^{\circ}C$ 높았으며 16kW 가동 시는 상부 평균온도가 하부보다 $0.2^{\circ}C$ 높았다. 전기발열체와 경유온풍난방기의 비교 시험에서는 난방 시 온실상부와 하부의 온도차가 전기발열체 온실이 $0.1{\sim}0.2^{\circ}C$로 경유온풍난방기 온실의 $0.5{\sim}0.6^{\circ}C$보다 작았으며, 온실 상류와 하류의 온도차는 전기발열체 온실이 $0{\sim}0.1^{\circ}C$로 경유온풍난방기 온실의 $1.3{\sim}1.4^{\circ}C$보다 작아 정밀한 온도관리가 가능하였다. 난방기간 동안 사용한 에너지사용량은 경유온풍난방기 온실이 경유 867L를, 전기발열체 온실이 전력량 8,959kWh를 사용하였으며, 난방비용은 각각 607천원과 403천원이 소요되어 전기발열체 온실에서 약 34%의 비용절감 효과가 있었다. 전기발열체 온실의 경우 상대적으로 군락 상하부의 환경관리가 균일하여 초장을 비롯한 전반적 생육상황이 경유온풍난방기 온실보다 좋았으나 통계적으로 유의한 차이는 없었으며, 수확량 역시 전기발열체 온실의 작물군락 하부 온도가 경유온풍난방기 온실보다 $1.3^{\circ}C$ 더 높게 관리되어 4.3% 증수효과가 있었으나 통계적으로 유의한 차이는 없었다. 원예시설의 최적 난방 관리를 위해서는 각 난방기의 열전달 특성에 기초하여 난방기 용량, 배치, 열분배 방법에 대한 설계가 요구되며, 전열선 형태의 난방기 역시 작물형상 및 재배방법을 고려하여 전열선의 개수, 위치, 방열온도 등에 대한 설계가 필요한 것으로 판단되었다.