• Tribology and Lubricants
• /
• v.35 no.4
• /
• pp.244-266
• /
• 2019

The purpose of this study is to estimate the wear volumes of engine journal bearings operating at variable angular velocity of a shaft in the beginning of firing start-up cycle. To do this, first we find the potential region of wear scar on engine journal bearings where the applied bearing load and crank shaft velocity are variable. The potential wear regions are discovered by finding minimum oil film thickness at every crank angle existing below most oil film thickness scaring wear (MOFTSW) obtained based on the concept of the centerline average surface roughness. Then we calculate the wear volume from the wear depth and two wear angles decided by the magnitude of each film thickness lower than MOFTSW at every crank angle. The results show that the expected wear region is located at a few bearing angles after and/or behind the upper center of a big-end bearing and the lower center of a main bearing. And the real wear region is similar to the estimated wear region. Further we find that the wear scar on an engine journal bearing may occur at re-starting time after switch-off of a start motor especially under the condition of high oil temperature.

• Proceedings of the Korea Society of Information Technology Applications Conference
• /
• 2005.11a
• /
• pp.289-291
• /
• 2005

In this paper, we introduce the backward solution of nonlinear wave equation for denoising. The PDE method is approved about 4 PSNR value compare with any convolution method. In neuro images, denoising process using proposed PDE is good about 0.2% increased Voxel Region.

• Journal of Environmental Science International
• /
• v.27 no.5
• /
• pp.309-317
• /
• 2018

In this study, a laser sheet technique and PLIF (Planar laser-induced fluorescence) are applied to a laboratory-scale pulverized coal burner of the open type, and the spatial relationship of the pulverized coal particle zone and the combustion reaction zone is examined by simultaneous measurement of Mie scattering and OH-LIF images. It is found that this technique can be used to investigate the spatial relationship of the combustion reaction zone and pulverized-coal particles in turbulent pulverized-coal flames without disturbing the combustion reaction field. In the upstream region, the combustion reaction occurs only in the periphery of the clusters where high-temperature burned gas of the methane pilot flame is entrained and oxygen supply is sufficient. In the downstream region, however, combustion reaction can be seen also within clusters of pulverized-coal particles, since the temperature of pulverized-coal particles rises, and the mixing with emitted volatile matter and ambient air is promoted.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.3
• /
• pp.305-314
• /
• 2001

A modified model is proposed for calculation of transitional boundary layer flows. In order to develop the eddy viscosity model for the problem, the flow is divided into three regions; namely, pre-transition region, transition region and fully turbulent region. The pre-transition eddy-viscosity is formulated by extending the mixing length concept. In the transition region, the eddy-viscosity model employs two length scales, i.e., pre-transition length scale and turbulent length scale pertaining to the regions upstream and the downstream, respectively, and a universal model of stream-wise intermittency variation is used as a function bridging the pre-transition region and the fully turbulent region. The proposed model is applied to calculate three benchmark cases of the transitional boundary layer flows with different free-stream turbulent intensity (1%∼6%) under zero-pressure gradient. It was found that the profiles of mean velocity and turbulent intensity, local maximum of velocity fluctuations, their locations as well as the stream-wise variation of integral properties such as skin friction, shape factor and maximum velocity fluctuations are very satisfactorily predicted throughout the flow regions.

• Journal of Environmental Science International
• /
• v.25 no.2
• /
• pp.239-246
• /
• 2016

This study aims to analyze region-specific trends in changing greenhouse gas emissions in incineration plants of local government where waste heat generated during incineration are reused for the recent five years (2009 to 2013). The greenhouse gas generated from the incineration plants is largely $CO_2$ with a small amount of $CH_4$ and $N_2O$. Most of the incineration plants operated by local government produce steam with waste heat generated from incineration to produce electricity or reuse it for hot water/heating and resident convenience. And steam in some industrial complexes is supplied to companies who require it for obtaining resources for local government or incineration plants. All incineration plants, research targets of this study, are using LNG or diesel fuel as auxiliary fuel for incinerating wastes and some of the facilities are using LFG(Landfill Gas). The calculation of greenhouse gas generated during waste incineration was according to the Local Government's Greenhouse Emissions Calculation Guideline. As a result of calculation, the total amount of greenhouse gas released from all incineration plants for five years was about $3,174,000tCO_2eq$. To look at it by year, the biggest amount was about $877,000tCO_2eq$ in 2013. To look at it by region, Gyeonggido showed the biggest amount (about $163,000tCO_2eq$ annually) and the greenhouse gas emissions per capita was the highest in Ulsan Metropolitan City(about $154kCO_2eq$ annually). As a result of greenhouse gas emissions calculation, some incineration plants showed more emissions by heat recovery than by incineration, which rather reduced the total amount of greenhouse gas emissions. For more accurate calculation of greenhouse gas emissions in the future, input data management system needs to be improved.

• Korean Journal of Materials Research
• /
• v.26 no.4
• /
• pp.167-172
• /
• 2016

The high temperature deformation behavior of $Ni_3Al$ and $Ni_3(Al,Mo)$ single crystals that were oriented near <112> was investigated at low strain rates in the temperature range above the flow stress peak temperature. Three types of behavior were found under the present experimental conditions. In the relatively high strain rate region, the strain rate dependence of the flow stress is small, and the deformation may be controlled by the dislocation glide mainly on the {001} slip plane in both crystals. At low strain rates, the octahedral glide is still active in $Ni_3Al$ above the peak temperature, but the active slip system in $Ni_3(Al,Mo)$ changes from octahedral glide to cube glide at the peak temperature. These results suggest that the deformation rate controlling mechanism of $Ni_3Al$ is viscous glide of dislocations by the <110>{111} slip, whereas that of $Ni_3(Al,Mo)$ is a recovery process of dislocation climb in the substructures formed by the <110>{001} slip. The results of TEM observation show that the characteristics of dislocation structures are uniform distribution in $Ni_3Al$ and subboundary formation in $Ni_3(Al,Mo)$. Activation energies for deformation in $Ni_3Al$ and $Ni_3(Al,Mo)$ were obtained in the low strain rate region. The values of the activation energy are 360 kJ/mol for $Ni_3Al$ and 300 kJ/mol for $Ni_3(Al,Mo)$.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.15 no.6
• /
• pp.69-77
• /
• 2012

This study observes the purchased lands in riparian areas of Suncheon City region and proposes a reasonable management method. For the study, the site surveying and analysis on the neglected purchased lands is executed, then, based on the site analysis result, the appropriate management method for each neglected purchased land is established. Each management method is approached from the ecological restoration perspective. According to site surveying and analysis of the neglected purchased lands, most of the sites were bare and agricultural lands. The reason for this is thought to be as when purchasing a land, the areas with higher nonpoint source pollution are bought preferentially. As for the dominant species coverage, 26% ($364,000m^2$) of the total neglected purchased land area in Sucheon City was covered with the dominated species, and for the exotic species coverage, 17% ($232,000m^2$) of the total neglected purchased land area in Sucheon City was covered with the exotic species. The survey site constituted of five different invasive species such as Japanese Hop (Humulus japonicus), Daisy Fleabane (Erigeron annuus), and Evening Primrose (Oenothera odorata). As for the natural succession on site, about 47% of the area showed poor natural succession process. The reason for this outcome is understood as having a lack of appropriate management for purchased lands. Based on the site surveying and analysis, especially the current management state of the and its location, the research site was categorized into preservation, restoration, and improvement sites. During the establishment of the ecological riparian belt, the comprehensive management for preservation, restoration, and improvement of the purchased lands should be executed.

• Korean Journal of Materials Research
• /
• v.26 no.7
• /
• pp.370-375
• /
• 2016

Tensile tests and creep tests were carried out at high temperatures on an Al-$Al_4C_3$ alloy prepared by mechanical alloying technique. The material contains about 2.0% carbon and 0.9% oxygen in mass percent, and the volume fractions of $Al_4C_3$ and $Al_2O_3$ particles are estimated at 7.4 and 1.4%, respectively, from the chemical composition. Minimum creep rate decreased steeply near two critical stresses, ${\sigma}_{cl}$ (the lower critical stress) and ${\sigma}_{cu}$ (the upper critical stress), with decreasing applied stress at temperatures below 723 K. Instantaneous plastic strain was observed in creep tests above a critical stress, ${\sigma}_{ci}$, at each test temperature. ${\sigma}_{cu}$ and ${\sigma}_{ci}$ were fairly close to the 0.2% proof stress obtained by tensile tests at each test temperature. It is thought that ${\sigma}_{cl}$ and ${\sigma}_{cu}$ correspond to the microscopic yield stress and the macroscopic yield stress, respectively. The lower critical stress corresponds to the local yield stress needed for dislocations to move in the soft region within subgrains. The creep strain in the low stress range below 723 K arises mainly from the local deformation of the soft region. The upper critical stress is equivalent to the macroscopic yield stress necessary for dislocations within subgrains or in subboundaries; this stress can extensively move beyond subboundaries under a stress above the critical point to yield a macroscopic deformation. At higher temperatures above 773 K, the influence of the diffusional creep increases and the stress exponent of the creep rate decreases.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.05a
• /
• pp.228-231
• /
• 2022

Most CCTVs operated by public institutions for crime prevention and parking enforcement are located on roads. The angle of these CCTV's view is often changed for various reasons, such as bolt loosening by vibration or shocking by vehicles and workers, etc. In order to effectively provide AI services based on the collected images, the service target area(ROI, Region Of Interest) must be provided without interruption within the image. This is also related to the viewpoint of effective operation of computing power for image analysis. This study explains how to maximize the application of artificial intelligence technology by setting the ROI based on the marker on the road, setting the image analysis to be possible only within the area, and studying the process of finding the ROI.

• Industry Promotion Research
• /
• v.9 no.1
• /
• pp.57-64
• /
• 2024

In 2015, the paradigm of hazardous chemical substance management in Korea shifted from the workplace to the regional level due to the complete revision of the Chemicals Control Act. Although regional chemical accident response plans were established in 2020, there were slight differences in the scope and criteria of each local government. Therefore, this study compared and analyzed chemical accident response plans established in four different regions to provide insights into effective chemical accident response plans. Based on publicly available information, the current status of accident preparedness, chemical accident response systems, and resident evacuation response and education/training were compared and analyzed. The results showed that there were not significant differences in the accident preparedness and response systems between the regions. However, there was a lack of discussion on the preparedness system linked to the characteristics of each workplace in each region. Additionally, there were differences in education and training for residents between regions. In the future, each local government needs to establish a response organization that fits the characteristics of their region and develop strategies for agile and effective accident response through cooperation with relevant agencies.