• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.3 no.1
• /
• pp.12-17
• /
• 1993

Growth runs of KTP single crystals were carried out by the hydrothermal method. KTP powders used for the crystal growth were prepared as a single phase by the solid state reaction of a stoichiometric mixture of $KH_2PO_4 and TiO_2$ at TEX>$800^{\circ}C$ and subsequently by the hydrothermal treatment at $250^{\circ}C$ 4m KF solution. The most effective solvents for the crystal growth of KTP were KF and K $K_2HPO_4$ solutions. Solubilities of KTP in these solutions were positive over the range $350~450^{\circ}C$.Seed crystals of good quality could be obtained by the horizontal temperature gradient method at temperatures over the range 380~430^{\circ}C$ in these solutions. The hydrothermal conditions for the high growth rates of seed crystals are as follows: growth method; vertical temperature gradient method, solvent; 4m KF or $K_2HPO_4$ solution, temperature region; $400~450^{\circ}C$, pressure region; $1000~1500kg/cm^2$, where solubility of KTP was large enough to proceed the growth. Under such conditions, seed crystals of KTP are grown at a rate of approximately 0.06-0.08mm/day in the direction of the c-axis. Morphologies of grown crystals tended to be bounded by (100), (011) and (201) faces.

• Wind and Structures
• /
• v.30 no.4
• /
• pp.433-450
• /
• 2020

The strong turbulence characteristic of typhoon not only will significantly change flow field characteristics surrounding the large-scale wind turbine and aerodynamic force distribution on surface, but also may cause morphological evolution of coast dune and thereby form sand storms. A 5MW horizontal-axis wind turbine in a wind power plant of southeastern coastal areas in China was chosen to investigate the distribution law of additional loads caused by wind-sand coupling movement of coast dune at landing of strong typhoons. Firstly, a mesoscale Weather Research and Forecasting (WRF) mode was introduced in for high spatial resolution simulation of typhoon "Megi". Wind speed profile on the boundary layer of typhoon was gained through fitting based on nonlinear least squares and then it was integrated into the user-defined function (UDF) as an entry condition of small-scaled CFD numerical simulation. On this basis, a synchronous iterative modeling of wind field and sand particle combination was carried out by using a continuous phase and discrete phase. Influencing laws of typhoon and normal wind on moving characteristics of sand particles, equivalent pressure distribution mode of structural surface and characteristics of lift resistance coefficient were compared. Results demonstrated that: Compared with normal wind, mesoscale typhoon intensifies the 3D aerodynamic distribution mode on structural surface of wind turbine significantly. Different from wind loads, sand loads mainly impact on 30° ranges at two sides of the lower windward region on the tower. The ratio between sand loads and wind load reaches 3.937% and the maximum sand pressure coefficient is 0.09. The coupling impact effect of strong typhoon and large sand particles is more significant, in which the resistance coefficient of tower is increased by 9.80% to the maximum extent. The maximum resistance coefficient in typhoon field is 13.79% higher than that in the normal wind field.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.3
• /
• pp.95-104
• /
• 2005

To know the proper setup posture for the various clubs, changes of setup variables according to the change of golf club length was investigated. Swing motions of three male low handicappers including a professional were taken using two high-speed videocameras. Four clubs iron 7, iron 5, iron 3 and driver (wood 1) were selected for this experiment. Three dimensional motion analysis techniques were used to get the kinematical variables. Mathcad and Kwon3D motion analysis program were used to analyze the position, distance and angle data in three dimensions. The variables divided into three categories 1) position and width of anterior-posterior direction 2) position and width of lateral direction 3) angles and evaluated based on the theories of many good golf teachers. Major findings of this study were as follows. 1.The stance (distance between ankle joints) was increased as the length of the club increased but the increasing width was not large. It ranges from 5cm to 10cm and professional player showed small changes. 2. Forward lean angle of trunk was decreased (more erected) as the length of the club increased. It ranges from 30 degrees for iron7 to 25 degrees for driver. 3. Angle between horizontal and right shoulder were increased as the length of the club increased. It ranges from 10 degrees to 20 degrees and professional player showed small changes. 4. Anterior-posterior position of the shoulders were located in front of the foot for all clubs and the difference between the shoulder and knee position was decreased as the length of the club increased. 5. Anterior-posterior position of grip (hand) was located almost beneath the shoulders (2.5cm front) for iron7, but it increased to 10cm for the driver. This grip adjustment makes the height of the posture increased only 5cm from iron7 to driver. 6. Lateral position of grip located at 5cm left for the face of iron7, but it located at the right side (behind) for the face of driver. 7. Lateral position of the ball located at the 40%(15cm) of stance from left ankle for iron7 and located at the 10% (5cm) of stance for driver. 8. Head always located at the right side of the stance and the midpoint of the eyes located at the 37% of stance from the right ankle for all clubs. This means that the axis of swing always maintained consistently for all clubs. 9. Left foot opened to the target for all subject and clubs. The maximum open angle was 25 degrees. Overall result shows that the changes of the setup variables vary only small ranges from iron7 to driver. Paradoxically it could be concluded that the failure of swing result from the excessive changes of setup not from the incorrect changes. These findings will be useful for evaluating the setup motion of golf swing and helpful to most golfers.

• Tunnel and Underground Space
• /
• v.17 no.2 s.67
• /
• pp.128-138
• /
• 2007

At low in-situ stress, the continuity and distribution of natural fractures in rock mass predominantly control the failure processes. However at high in-situ stress, the failure process are affected and eventually dominated by stress-induced fractures preferentially growing parallel to the excavation boundary. This fracturing is often observed in brittle type of failure such as slabbing or spatting. Recent studies on the stress- or excavation-induced damage of rock revealed its importance especially in a highly stressed regime. In order to evaluate the brittle failure around a deep underground opening, physical model experiments were carried out. For the experiments a new tue triaxial testing system was made. According to visual observation and acoustic emission detection, brittle failure grades were classified under three categories. The test results indicate that where higher horizontal stress, acting perpendicular $(S_{H2})$ and parallel $(S_{H1})$ to the axis of the tunnel respectively, were applied, the failure grade at a constant vertical stress level (Sy) was lowered. The failure initiation stress was also increased with the increasing $S_{H1}\;and\;S_{H2}$. From the multi-variable regression on failure initiation stress and true triaxial stress conditions, $f(S_v,\;S_{H1},\;S_{H2})$ was proposed.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.8 no.2
• /
• pp.94-110
• /
• 2003

This study utilizes the dataset of Topex/Poseidon(T/P) altimeter sea surface height (1992-2000 yr., 286 cycles)to investigate the tempore-spatial variability in the East (Japan) Sea. Optimal interpolation (Ol) technique was applied to the pre-processed T/P dataset (level 2) to produce sea surface height anomaly (SSHA) map on regular grids. Spectral analyses of the timeseries of the SSHA at chosen stations and empirical orthogonal function (EOF) analysis of the SSHA in the entire East Sea were made. Distribution of the SSHA can be divided by the southern and northern regions sharply by the polar front situated in the middle of the East Sea. The southern region under the direct influence of the Tsushima Current exhibits higher amplitude of the SSHA fluctuation, while the northern region does relatively smaller one. The spatio-temporal variability of the SSHA in the East Sea can be characterized by the five modes of the EOFs accounting for more than 85% of the total variance. The first mode dominates the SSHA variation in the entire domain with strong seasonal and inter-annual periods accounting for the 72.3% of the total variance. The other modes (up to 5th account for 14%) are responsible for the SSHA variation associated with the local current system, meandering of the polar frontal axis, and mesoscale eddies. Spectral peaks with significant confluence level show semi-annual, annual and interannual (2, 3-4 years) periods.

• Journal of Periodontal and Implant Science
• /
• v.49 no.5
• /
• pp.299-309
• /
• 2019

Purpose: To analyze the ridge profile of the anterior maxilla using cone-beam computed tomography and to assess the clinical significance of the ridge profile by performing virtual implant placement. Methods: Thirty-two cone-beam computed tomography scans of anterior maxillae were included. For each tooth, a vertical line was made along the longitudinal axis, and 3 horizontal lines at 1-, 3-, and 5-mm levels below the labial bone crest were drawn perpendicularly to the vertical reference. At these levels, the thickness of the alveolar ridge (RT), and the labial (LT) and palatal bone plate (PT) were measured. Then, virtual implant placement using standard and tapered implants was performed. A generalized linear mixed model was used for statistical analysis. Results: The teeth were located labially based on the proportion of LT and PT with respect to RT. At the 1-mm level, the value of LT was between $1.0{\pm}0.4mm$ for central incisors and $1.3{\pm}0.6mm$ for canines. A large number of teeth had area(s) with less than 1-mm-thick labial bone between the 1- and 5-mm levels below the crest. The mean PT was generally thicker than the LT in all tooth types. The greatest mean value of labial concavity was observed for canines, compared to other tooth types. Men had a greater RT than did women, but had a comparable LT. Less apical fenestration was observed when tapered implants were used. Conclusions: Most teeth in the anterior maxilla had a thin labial bone plate, with no significant difference between sexes. Tapered implants may be advantageous for the anterior maxilla.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.24 no.2
• /
• pp.39-56
• /
• 2021

The seed zone is a map that describes the areas where plant material can be transferred with little risk for properly adapting to a new location. The seed zone study is largely divided into studies based on genetic data and studies based on climatic data. Can be. This study was conducted to establish a temporary domestic seed zone applicable to the entire Korean Peninsula and evaluate its possibility based on the US climate-based seed zone establishment methodology. The temporary seed zone was constructed in the same way as the US case by superimposing the data obtained by dividing the winter minimum temperature into 12 grades and the data obtained by dividing the annual heat: moisture index into 6 grades. As a result of the analysis, 65 temporary seed zones were formed throughout the Korean Peninsula, and the areas of the seed zones representing the smallest and largest areas were 3.0km² and 29,423.0km², respectively, and it was confirmed that they had an average size of about 5,064.9km². Temporary seed zones applied in Korea show a pattern of changes in temperature according to the relatively horizontal forest zone, and it was confirmed that the area where the Baekdu-daegan ecological axis is located has a tendency to show lower dryness than other areas. This study applied the US climate-based seed zone methodology in Korea as a pilot, and confirmed the climatic similarity across the Korean Peninsula. Furthermore, it is expected to provide an optimal seed map that improves the success rate of restoration in the future by revising the seed zone grade suitable for the domestic environment in consideration of the results of this study and the possibility of seed adaptation to the field survey and environmental space.

• Journal of Advanced Navigation Technology
• /
• v.26 no.3
• /
• pp.160-165
• /
• 2022

In this paper, we have proposed a magnetic resonant 6.78MHz WPT(wireless power transfer) technique which can be applied to a fixed transmitter and a receiver of varying relative distance and coil alignment, Power transmission characteristics are studied with the relative distance and misalignment ration of coil area between the transmitting and receiving coils. The coils are designed with the size of 60×80mm² by direct feeding method, and the characteristics are derived with the maximum relative distance of 50mm and horizontal area misalignment state of 0-40mm misalignment of coil center axis in the XY plane. The power transmission characteristics are compared between the 3D EM simulation and the measured data, and the power transmission shows larger than -3dB performance with the vertical distance of up to 30mm and 50% area misalignmment ratio. This work showsthe transmission characteristics according to relative distance and misalignment state between the cols and that direct feeding has advantage for the short relative distance and small misalignment ratio.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.23 no.2
• /
• pp.25-32
• /
• 2021

There is a need to breed and distribute of domestic varieties for Lilium longiflorum because most of the lily bulbs cultivated in Korea were imported from foreign country. The L. longiflorum 'Ace' and 'Nellie White' collected from 1996 had been self-crossed from 1996 to 2010. In 2012, the L. longiflorum 'Bright LoSong' was developed as a F₁ hybrid crossed between 'L₂-17-4' and 'L₂-16-6' that obtained by 7th self-fertilization. The 'Bright LoSong' was tested for homogeneity, regional adaptability test, consumer preference show from 2014 to 2015, and it was registered in 2017. The flower of 'Bright LoSong' is a trumpet shaped single flower with no spots.It has 5.8 flowers per plant, which is a relatively many number compared control 'Mount Carmel', Its flower diamater is 9.8cm, relatively a bit small size. And the flower inflorescence has umbel or raceme while the attitude of longitudinal axis is horizontal. The plant height is 38.4cm with 30.8 leaves per plant and 1.9cm of the leaf width. 'Bright LoSong' has a longer flowering period because of relatively small diameter or many number of flowers than those of the control 'Mount Carmel'. Thus, the 'Bright LoSong' showed a high consumer preference, and the cultivar has the advantage of being able to reproduce since the parents are pure lines.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.4
• /
• pp.1-10
• /
• 2023

In the seismic design of structures, seismic forces are calculated based on structural models and analysis. In order to accurately address the dynamic characteristics of the actual structure in the structural model, calibration based on actual measurements is required. In this study, a 4-story frame test specimen was manufactured to simulate frame building, accelerometers were attached at each floor, and 1-axis shaking table test was performed. The natural period of the specimen was similar to that of the actual 4 story frame building, and the columns were designed to behave with double-curvature having the infinite stiffness of the horizontal members. To investigate the effects seismic waves characteristics, historical and artificial excitations with various frequencies and acceleration magnitudes were applied. The natural frequencies, damping ratios, and mode shapes were obtained using frequency response functions obtained from dynamic response signals, and the mode vector deviations according to the input seismic waves were verified using the Mode assurance criterion (MAC). In addition, the damping ratios obtained from the vibration tests were applied to the structural model, and the method with refined dynamic characteristics was validated by comparing the analysis results with the experimental data.