• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.6 s.99
• /
• pp.706-711
• /
• 2005

Torsional oscillations of a system incorporating a Hooke's joint are investigated by studying a simple similar nonlinear 2-degree-of-freedom model, which has linear and quadratic nonlinear parametric excitations. The simple system is identified to have the possibilities of primary, sub harmonic and combination resonances. The case of simultaneous primary and combination resonances is selected for perturbation analysis to have the reduced amplitude-equations of motion. The same procedure is applied to the system incorporating a Hooke's joint.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.4
• /
• pp.317-322
• /
• 2003

Torsional oscillations of a system incorporating a Hooke's joint are investigated by adopting a nonlinear 2-degree-of-freedom model. Linear and Van der Pol transformations are applied to obtain the equations of motion to which the method of averaging can be readily applied. Various subharmonic and combination resonances are identified with the conditions of their occurrences. Applying the method of averaging leads to the reduced amplitude- and phase-equations of motion, of which constant and periodic solutions are obtained numerically. The periodic solution which emerges from Hopf bifurcation point experiences period doubling bifurcation leading to infinite solution rather than chaotic solution.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.110-115
• /
• 1995

In this paper, the problem of non-linear torsional oscillation of a system incorporating a Hooke's joint is studied. Classical perturbation methods including higher order averaging and bifurcation theory are adopted for analysis. The equation of motion derived by Porter[1] is presented and the type of the system is identified. It has been found that two important cases deserve extensive study. Method of higher order averaging which is a main research tool in this study is introduced briefly. The averaged equations are studied analyticallyand numerically and the method of averaging has been found to be effective to study complex non-linear system.

• Journal of Power System Engineering
• /
• v.1 no.1
• /
• pp.98-105
• /
• 1997

In general, crankshafts which are used in internal combustion reciprocating engines are subjects to high torsional vibration. Therefore, a damper is often used to minimize the torsional vibration in reciprocating engines. In this paper, in order to investigate damping performance of viscous damper, the real effective viscosity and complex damping coefficient of silicone oil, and the effective inertia moment of inertia ring are calculated considering the relative motion between damper casing and inertia ring. Based on these results multi-cylinder shaft is modeled into equivalent 2-degree of freedom system and optimum condition is estimated by calculating the amplification factor of viscous damper. Also the test damper was manufactured according to the result of theoretical investigation, the performance and durability was ascertained through experimental examination.

• Journal of Adhesion and Interface
• /
• v.5 no.2
• /
• pp.14-26
• /
• 2004

For reliable determination of mechanical characteristics of adhesively bonded joints used e.g. as input data for computer-aided design of complex components, the thick-adherend tensile-shear test according to ISO 11003-2 is the most important material testing method. Although the total displacement of the joint is measured across the polymer layer directly in the overlap zone in order to minimize the influence of the stepped adherends, the substrate deformation must be taken into account within the framework of the evaluation of the shear modulus and the maximum shear strain, at least when high-strength adhesives are applied. In the standard ISO 11003-2 version of 1993, it was prescribed to perform the substrate deformation correction by means of testing a one-piece reference specimen. The authors, however, pointed to the excessive demands on the measuring accuracy of the extensometers connected with this technique in industrial practice and alternatively proposed a numerical deformation analysis of a dummy specimen. This idea of a mathematical correction was included in the revised ISO 11003-2 version of 2001 but in the simplified form of an analytical method based on Hooke's law of elasticity for small strains. In the present work, it is shown that both calculation techniques yield considerably discordant results. As experimental assessment would require high-precision distance determination (e.g. laser extensometer), finite element analyses of the deformation behavior of the bonded joint are performed in order to estimate the accuracy of the obtained substrate deformation corrections. These simulations reveal that the numerical correction technique based on the finite element deformation modeling of the reference specimen leads to considerably more realistic results.