• 한국주조공학회지
• /
• 제17권5호
• /
• pp.443-449
• /
• 1997

The purpose of this study is to investigate the effect of P addition and homogenizing heat treatment on the mechanical properties of Cu-Sn-Ni alloy. The addition of P was 0.025wt.%P to 0.085wt.%P and homogenizing heat-treated at 400, 500, $600^{\circ}C$ under $N_2$ gas atmosphere. Mechanical properties was investigated in this study were Rockwell hardness, tensile strength, and elongation. Tensile strength and elongation increased with P and homogenizing time. Temperature was significantly influence on mechanical properties. Hardness decreased with increasing homogenizing time and temperature, but 0.085wt.%P specimen was showed higher hardness and lower tensile strength and elongation than 0.073wt.%P specimen due to the presence of more $Cu_3P$ in matrix.

• 한국주조공학회지
• /
• 제17권5호
• /
• pp.450-457
• /
• 1997

Effects of Ti addition and homogenizing heat treatment on the mechanical properties in Cu-Zn-Al alloy (high strength yellow brass) were investigated. Grain refinement was successfully achieved by Ti addition. The microstructure, which was composed of island or fine feather-like branched Ti compounds was changed to feather-like eutectic microstructure as the content of Ti increased. The highest hardness value was obtained for 0.5 wt.% Ti specimen and the second was Ti non-added specimen in as-cast condition. The highest tensile strength was obtained for 0.5 wt.% Ti specimen. Because of the presence of cast defects and worse castability, tensile strength decreased as the content of Ti increased. Elongation increased with increasing homogenizing time and temperature; remarkable increase was obtained for $400^{\circ}C$ homogenizing temperature in the 0.5 wt.% Ti specimen. For $500^{\circ}C$ and $600^{\circ}C$ homhgenizing, temperature, high elongation was obtained in 2 and 4 wt.% Ti specimen.

• 대한금속재료학회지
• /
• 제47권4호
• /
• pp.242-247
• /
• 2009

On the Transient Liquid Phase Bonding (TLPB) phenomenon with the MBF-50 insert metal at narrow gap (under 100), it takes long time for the bonding and the homogenizing. Typically, isothermal solidification is controlled by the diffusion of depressed element of B and Si. However, the amount of B and Si in the MBF-50 filler metal is large. This is reason of the long bonding time. Also, the MBF-50 filler metal did not contained Al and Ti which are ${\gamma}^{\prime}$ phases former. This is reason of the long homogenizing time. From the bonding phenomenon with the MBF-50 insert metal, we search main factors on the bonding mechanism and select several insert-metals for using the wide-gap TLPB. New insert-metals contained Al and Ti which are ${\gamma}^{\prime}$ phases former and decrease the B then the MBF-50. When the new insert-metal was used on the TLPB, the bonding time was decreased about 1/10 times and homogenizing heat treatment was no needed. In spite of the without homogenizing, the volume fraction of ${\gamma}^{\prime}$ phases in the boned interlayer was equal to homogenizing heat treated specimen which was TLPB with the MBF-50. Finally, the new insert metal named WG1 for the wide-gap TLPB is more efficient then the MBF-50 filler metal without decreasing the bonding characteristic.

• 한국재료학회지
• /
• 제5권1호
• /
• pp.132-139
• /
• 1995

Al-Mg-Cu-Mn계 합금을 가공열처리하고 초소성 특성을 조사한 후 광학 및 전자 현미경을 이용하여 초소성에 영향을 미치는 주요한 인자들을 조사하였다. 균질화 과정에서 제거되지 않은 조대한 2차상들은 그 후의 가공열처리 과정에서도 계속 잔류하여 초소성 변형 중 기공을 유발함으로써ㅓ 초소성 신율을 저하시켰다. 반면에 가공열처리 과정에서 생성된 미세한 석출물은 결정립 성장을 억제하여 조직을 안정화함으로써 초소성 특성을 향상시켰다. 균질화처리 조건은 2차상의 크기과 분포에 큰 영향을 주어 2단계 균질화-공냉처리는 1단계 균질화-노냉처리보다 조대한 2차상의 제거와 미세석출물의 생성에 효과적이었다.

• Journal of Welding and Joining
• /
• 제21권3호
• /
• pp.78-84
• /
• 2003

The changes of microstructure and hardness of TLP bonds of directionally solidified Ni base superalloy, GTD-111, with variation of homogenizing and aging treatment were investigated. The specimens were bonded at 1403K for 7.2ks using different insert metals such as MBF-50, MBF-80 and MBF-90 and they were homogenized at 1393K with various holding time. At center of bonded interlayer homogenized for hold time 30h, the contents of aluminum and titanium were approximately 90% and 95% of base metal, respectively. In this study, aging was performed at three different kinds : one step aging ; 1113K $\times$ 16h, two step aging ; 1113K $\times$ 10h ⇒ 1103K $\times$ 10h, three step aging ; 1113K $\times$ 10h ⇒ 1103K $\times$ 8h ⇒ 922K $\times$ 24h. ${\gamma}$' volume fraction and hardness of joints were high in the sequence of one step, two step and three step aging, whereas ${\gamma}$' volume fraction and hardness of joints obtained by three step aging treatment were higher than those of raw material. Tensile properties of joints bonded with MBF-80 and MBF-90, homogenized at 1393K for 30h and then three step aged became excellent than those of raw material, however, joint bonded with MBF-50 was poor.

• Tribology and Lubricants
• /
• 제19권5호
• /
• pp.285-291
• /
• 2003

Ultrasonic vibrator is an equipment which atomizes and homogenization the oils by breaking the oil particles with ultrasonic cavitation, and would improve the properties. The present study deal with the ultrasonic breaking systems which recycle the shipborne waste oil into usable oil to be burnt. The first place, experimental studies were carried out to investigate the homogenizing effect of the waste oils by ultrasonic cavitation. Variation of the properties(viscosity, specific gravity and pH) and the matrix structures for the various shipborne waste oils were interpreted to analyse the breaking, dispersion effects by ultrasonic cavitation. The experimental results can be useful to the development of waste oil disposing systems.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2000년도 특별강연 및 추계학술발표대회 개요집
• /
• pp.222-223
• /
• 2000

• Journal of Welding and Joining
• /
• 제13권3호
• /
• pp.147-156
• /
• 1995

The change of microstructure in the bonded interlayer and tensile properties of joints were studied for liquid phase diffusion bonding using STS-310 and Incoloy-825 as base metal and base metal+B alloy as insert inetal. Main experimental results obtained in this study are as follows. 1) The optimum amount of B addition into the insert metal was found to be about 4mass%. 2) When isothermal solidification was completed, the microstructure in the bonded interlayer was the same with that of the base metal because of the grain boundary migration in the bonded interlayer. 3) All of the tensile specimen fractured at base metal and joints bonded at optimum condition exhibited tensile properties in excess of base metal requirements. 4) It was determined that fine car-borides and bordes such as M$_{23}$(C,B)$_{6}$, Cr$_{2}$B, and CrB in STS-310S and TiB in Incoloy-825 exist at the grain boundary around bonded interlayer. These precipitates almost disappeared after homogenizing treatment at 1373K for 86.4ks.s.

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2006년도 추계학술발표회
• /
• pp.291-297
• /
• 2006

최근 국제 유가의 상승으로 인한 선박 운용비를 절감하기 위하여 중소형 선박에서도 저질연료유의 사용이 검토되고 있는 추세이다. 이 연구에서는 현재 중소형 선박에서 연료유로 사용중인 경유와 중유 MF380 을 혼합하여 소형선박에 사용이 가능하도록 제조한 혼합연료유인 MF30 연료유에 대하여 그 물리 화학적 특성을 분석하고 정제처리 및 연료유첨가제 효과에 대해 알아보았다. 연구 결과 두가지 전처리 방식인 원심식청정기와 가열 및 균질 방식 (M.C.H) 의 효과는 다소 미약하였지만, 유동점과 인화점은 다소 낮아졌다. 연료유첨가제로 인한 개질 효과는 뚜렷이 나타나지 않았다.

• 해양환경안전학회지
• /
• 제13권1호
• /
• pp.39-45
• /
• 2007

최근 국제 유가의 상승으로 인한 선박 운용비를 절감하기 위하여 중소형 선박에서도 저질연료유의 사용이 검토되고 있는 추세이다. 이 연구에서는 현재 중소형 선박에서 연료유로 사용중인 경유와 중유MF380을 혼합하여 소형선박에 사용이 가능하도록 제조한 혼합연료유인 MF30 연료유에 대하여 그 물리 화학적 특성을 분석하고 정제처리 및 연료유첨가제 효과에 대해 알아보았다. 연구결과 두 가지 전처리 방식인 원심식청정기와 가열 및 균질 방식(M.C.H)의 효과는 다소 미약하였지만, 유동점과 인화점은 다소 낮아졌다. 연료유첨가제로 인한 개질 효과는 뚜렷이 나타나지 않았다.