• 한국멀티미디어학회논문지
• /
• 제24권3호
• /
• pp.431-439
• /
• 2021

Since the sensor nodes are randomly arranged in the region of interest, it may happen that the sensor network area is separated or there is no sensor node in some area. In addition, after the sensor nodes are deployed in the sensor network, a coverage hole may occur due to the exhaustion of energy or physical destruction of the sensor nodes. The coverage hole can greatly affect the overall performance of the sensor network, such as reducing the data reliability of the sensor network, changing the network topology, disconnecting the data link, and worsening the transmission load. Therefore, sensor network coverage hole recovery has been studied. Existing coverage hole recovery studies present very complex geometric methods and procedures in the two-step process of finding a coverage hole and recovering a coverage hole. This study proposes a method for discovering and recovering a coverage hole in a sensor network, discovering that the sensor node is a boundary node by itself, and determining the location of a mobile node to be added. The proposed method is expected to have better efficiency in terms of complexity and message transmission compared to previous methods.

• 디지털산업정보학회논문지
• /
• 제16권4호
• /
• pp.9-17
• /
• 2020

When IoT sensor nodes are deployed in areas where data collection is challenging, sensors must be relocated if sensing holes occur due to improper placement of sensors or energy depletion, and data collection is impossible. The sensing hole's cluster header transmits a request message for sensor relocation to an adjacent cluster header through a specific relay node. However, since a specific relay node is frequently used, a member sensor located in a specific cluster area adjacent to the sensing hole can continuously receive the movement message. In this paper, we propose a method that avoids the situation in which the sensing hole cluster header monopolizes a specific relay node and allows the cluster header to use multiple relay nodes fairly. Unlike the existing method in which the relay node immediately responds to the request of the header, the method proposed in this paper solves a ping-pong problem and a problem that the request message is concentrated on a specific relay node by applying a method of responding to the request of the header using a timer. OMNeT++ simulator was used to analyze the performance of the proposed method.

• 대한기계학회논문집B
• /
• 제27권7호
• /
• pp.948-955
• /
• 2003

Pressure coefficient in rotating discharge hole was measured to gain insight into the influence of rotation to the discharge characteristics of rotating discharge hole. Pressure measurements were done by the telemetry system that had been developed by the authors. The telemetry system measures static pressure using piezoresistive pressure sensors. Pressure coefficients in rotating discharge hole were measured in longitudinal direction and circumferential direction with various rotating speed and 3 pressure ratios. From the results, the pressure coefficient, and therefore the discharge coefficient, is known to decrease with the increase of Ro number owing to the increase of flow approaching angle to the discharge hole inlet. However, there exists critical Ro number where the decrease rate of discharge coefficient with the increase of Ro number changes abruptly; flow separation occurs from the discharge hole exit at this critical Ro number. Critical Ro number increases with the increase of length-to-diameter ratio, but the increase is small where the length-to-diameter ratio is higher than 3. The decrease rate of discharge coefficient with the increase of Ro number depends on the pressure recovery at the discharge hole, and the rate is different from each length-to-diameter ratio; it has tendency that the short discharge hole shows higher decrease rate of discharge coefficient.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제45권5호
• /
• pp.276-284
• /
• 2019

Objectives: This study sought to compare efficiency results between the use of a customized implant (CI) and a reconstruction plate (RP) in mandibular defect reconstruction in an animal model. Materials and Methods: Fifteen rabbits underwent surgery to create a defect in the right side of the mandible and were randomly divided into two groups. For reconstruction of the mandibular defect, the RP group (n=5) received five-hole mini-plates without bone grafting and the CI group (n=10) received fabricated CIs based on the cone-beam computed tomography (CBCT) data taken preoperatively. The CI group was further divided into two subgroups depending on the time of CBCT performance preoperatively, as follows: a six-week CI (6WCI) group (n=5) and a one-week CI (1WCI) group (n=5). Daily food intake amount (DFIA) was measured to assess the recovery rate. Radiographic images were acquired to evaluate screw quantity. CBCT and histological examination were performed in the CI subgroup after sacrifice. Results: The 1WCI group showed the highest value in peak average recovery rate and the fastest average recovery rate. In terms of reaching a 50% recovery rate, the 1WCI group required the least number of days as compared with the other groups ($2.6{\pm}1.3days$), while the RP group required the least number of days to reach an 80% recovery rate ($7.8{\pm}2.2days$). The 1WCI group showed the highest percentage of intact screws (94.3%). New bone formation was observed in the CI group during histological examination. Conclusion: Rabbits with mandibular defects treated with CI showed higher and faster recovery rates and more favorable screw status as compared with those treated with a five-hole mini-plate without bone graft.

• 에너지공학
• /
• 제24권2호
• /
• pp.17-21
• /
• 2015

다공 및 다단오리피스열을 해석할 수 컴퓨터코드를 사용하여 원자력발전소 내 공급 및 배출장치의 수축오리피스를 설계하였다. 원래 단공 오리피스가 설치되었으나 다공 오리피스 설치가 필요하여 설계 변경되었다. 오리피스 사이 거리는 충분한 압력회복거리로 유지되었다. 최소 정압은 공동현상 방지를 위하여 그 온도에 상응하는 증기압 이하로 유지되도록 설계하였다. 오리피스 설치 배관의 직경은 운전시 강성을 유지할 수 있도록 원래 크기보다 증가시켰다.

• 한국컴퓨터정보학회논문지
• /
• 제24권4호
• /
• pp.169-176
• /
• 2019

Wireless sensor networks are used to monitor and control areas in a variety of military and civilian areas such as battlefield surveillance, intrusion detection, disaster recovery, biological detection, and environmental monitoring. Since the sensor nodes are randomly placed in the area of interest, separation of the sensor network area may occur due to environmental obstacles or a sensor may not exist in some areas. Also, in the situation where the sensor node is placed in a non-relocatable place, some node may exhaust energy or physical hole of the sensor node may cause coverage hole. Coverage holes can affect the performance of the entire sensor network, such as reducing data reliability, changing network topologies, disconnecting data links, and degrading transmission load. It is possible to solve the problem that occurs in the coverage hole by finding a coverage hole in the sensor network and further arranging a new sensor node in the detected coverage hole. The existing coverage hole detection technique is based on the location of the sensor node, but it is inefficient to mount the GPS on the sensor node having limited resources, and performing other location information processing causes a lot of message transmission overhead. In this paper, we propose an Adjacent Matrix-based Hole Coverage Discovery(AMHCD) scheme based on connectivity of neighboring nodes. The method searches for whether the connectivity of the neighboring nodes constitutes a closed shape based on the adjacent matrix, and determines whether the node is an internal node or a boundary node. Therefore, the message overhead for the location information strokes does not occur and can be applied irrespective of the position information error.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.151-156
• /
• 1992

The purpose of this paper is to investigate the relationship between static pressure recovery and velocity distributions in case of swirling flow into a conical diffuser. In this research, velocity distribution is measured by a multi-hole yaw-meter. The following conclusions can be drawn from the experiments. (1) The static pressure recovery depends strongly on the strength of a swirl. (2) A high pressure recovery coefficient is achieved by inserting a solid core into the diffuser center.

• Clinics in Shoulder and Elbow
• /
• 제2권1호
• /
• pp.8-13
• /
• 1999

The results of the operative treatment of the Grade III acromioclavicular joint injury is defined by the durability of the reduced joint and free of exertional pain. Several surgical techniques have been applied to reduce and stabilize the joints effectively. Resection of clavicular lateral end and subacromial decompression also could be applied to prevent post-operative arthritic change. Biomechanical studies reveals the role of clavicular elevation and rotation to achieve more than 90 degrees of elevation. It also serves as a attachment site of deltoid and trapezius muscle. The stability and mobility of the both acromioclavicular and coracoclavicular joint are important to get full functional recovery. We modified the methods of coracoacromial ligament transfer described by Weaver-Dunn and by Shoji et a!. to pre­vent pullout of the transferred ligament and to get more improved functional results. Main technical point was harvesting full thickness bone block and fix it through the key-hole to reduce pull out angle.

• Structural Engineering and Mechanics
• /
• 제59권1호
• /
• pp.37-57
• /
• 2016

Reservoir geomechanics can play an important role in hydrocarbon recovery mechanism. In $CO_2$-EOR process, reservoir geomechanics analysis is concerned with the simultaneous study of fluid flow and the mechanical response of the reservoir under $CO_2$ injection. Accurate prediction of geomechanical effects during $CO_2$ injection will assist in modeling the Carbon dioxide recovery process and making a better design of process and production equipment. This paper deals with the implementation of a program (FORTRAN 90 interface code), which was developed to couple conventional reservoir (ECLIPSE) and geomechanical (ABAQUS) simulators, using a partial coupling algorithm. A geomechanics reservoir partially coupled approach is presented that allows to iteratively take the impact of geomechanics into account in the fluid flow calculations and therefore performs a better prediction of the process. The proposed approach is illustrated on a realistic field case. The reservoir geomechanics coupled models show that in the case of lower maximum bottom hole injection pressure, the cumulative oil production is more than other scenarios. Moreover at the high injection pressures, the production rates will not change with the injection bottom hole pressure variations. Also the FEM analysis of the reservoir showed that at $CO_2$ injection pressure of 11000 Psi the plastic strain has been occurred in the some parts of the reservoir and the related stress path show a critical behavior.

• 한국항공우주학회지
• /
• 제37권1호
• /
• pp.69-75
• /
• 2009

본 논문은 새로운 개념의 초음속 혼합기인 벤트 혼합기의 형상적 특성에 따른 공력 특성을 연구하였다. 홀의 크기는 2 mm이며 혼합기 벽면에서 2 mm 떨어진 곳에 위치한 모델(case 1)과 혼합기 벽면 뒤쪽에 위치한 모델(case 2)의 경우 같은 전압력 회복율을 보였으며, 홀의 크기를 반으로 줄인 1 mm(case 3) 모델은 cases 1, 2에 비해 낮은 전압력 회복율을 보였다. 재순환 영역의 크기는 cases 1-3은 같지만 전단층 두께는 cases 1, 2가 case 3 보다 두꺼웠다. 재순환 영역 내 압력 손실의 경우 cases 1, 2은 case 3에 비해 낮은 압력 손실과 높은 속도 구배를 보였으며, 이는 재순환 영역 내 공기와 연료의 혼합을 증대시키는 요인이다. 재순환 영역 내로 유입 되는 유동에 의해 형성되는 박리 버블은 연소기의 전압력 회복율과 재순환 영역 내 압력 분포와 순환 유동에 영향을 미친다. 따라서 박리 버블 형성에 영향을 주는 유입 공기 유량이 벤트 혼합기 성능에 주요한 영향을 미치는 것을 알 수 있다.