• 터널과지하공간
• /
• 제21권3호
• /
• pp.225-234
• /
• 2011

본 연구에서는 암반에서의 열 전달과 관련된 열-역학적 거동을 평가하기 위한 현장 히터시험을 국내 최초로 실시하였다. 현장시험을 위해 현장조건과 시험 목적에 부합하는 시추공 히터시험을 설계하고 히터장치, 관측용 센서, 데이터로깅 시스템의 설치가 이루어졌다. 시험 구간에서의 노출면 조사를 통해 고경사 절리가 우세하게 분포함을 알 수 있었으며 암석코아에 대한 실험실 실험을 통해 히터시험구간에서의 주요 열, 역학적 암반 물성을 결정하였다. 암반의 온도분포 변화를 통해 암반 내에 존재하는 절리의 영향과 터널 벽면으로의 열손실을 파악할 수 있었으며 히터온도가 $90^{\circ}C$로 유지되는 경우, 히터공에서 0.3 m 떨어진 암반의 온도는 최대 $40^{\circ}C$까지 상승함을 알 수 있었다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제21권3호
• /
• pp.64-81
• /
• 2016

To analyze the influence of various groundwater flow rates (specific discharge) on BHE system with balanced and unbalanced energy loads under assuming same initial temperature (15℃) of ground and groundwater, numerical modeling using FEFLOW was used for this study. When groundwater flow is increased from 1 × 10⁻⁷ to 4 × 10⁻⁷m/s under balanced energy load, the performance of BHE system is improved about 26.7% in summer and 22.7% at winter time in a single BHE case as well as about 12.0~18.6% in summer and 7.6~8.7% in winter time depending on the number of boreholes in the grid, their array type, and bore hole separation in multiple BHE system case. In other words, the performance of BHE system is improved due to lower avT in summer and higher avT in winter time when groundwater flow becomes larger. On the contrary it is decreased owing to higher avT in summer and lower avT in winter time when the numbers of BHEs in an array are increased, Geothermal plume created at down-gradient area by groundwater flow is relatively small in balanced load condition while quite large in unbalanced load condition. Groundwater flow enhances in general the thermal efficiency by transferring heat away from the BHEs. Therefore it is highly required to obtain and to use adequate informations on hydrogeologic characterristics (K, S, hydraulic gradient, seasonal variation of groundwater temperature and water level) along with integrating groundwater flow and also hydrogeothermal properties (thermal conductivity, seasonal variation of ground temperatures etc.) of the relevant area for achieving the optimal design of BHE system.

• 한국지반공학회논문집
• /
• 제21권9호
• /
• pp.65-75
• /
• 2005

흙의 최대 전단탄성계수는 동적/정적 지반구조물 설계에서 중요하게 다루어야 하는 기본 토질상수이다. 본 연구에서는 서해안 송도 지역의 실트질 모래에 대해 표준관입시험, 콘관입시험, 자가굴착식 공내재하시험, 다운홀 시험, 탄성파 탐사 콘관입시험, 공진주 시험 등을 수행하여 최대 전단탄성계수를 구하고 그 결과를 통계적으로 분석하였다. 다운홀 시험을 기준으로 표준관입시험 및 콘관입시험에 대한 경험식으로 구한 최대 전단탄성계수를 비교하고 새로운 경험식물 제안하였다. 제안식으로 구한 전단탄성계수는 다운홀 시험 결과와 비교적 잘 일치하였으며, 제안식을 이용하여 적절히 지반의 최대 전단탄성계수를 평가할 수 있음을 확인하였다.

• 한국재료학회지
• /
• 제27권2호
• /
• pp.107-112
• /
• 2017

The BCBJ (Back Contact and Back Junction) or back-lit solar cell design eliminates shading loss by placing the pn junction and metal electrode contacts all on one side that faces away from the sun. However, as the electron-hole generation sites now are located very far from the pn junction, loss by minority-carrier recombination can be a significant issue. Utilizing Medici, a 2-dimensional semiconductor device simulation tool, the interdependency between the substrate thickness and the minority-carrier recombination lifetime was studied in terms of how these factors affect the solar cell power output. Qualitatively speaking, the results indicate that a very high quality substrate with a long recombination lifetime is needed to maintain the maximum power generation. The quantitative value of the recombination lifetime of minority-carriers, i.e., electrons in p-type substrates, required in the BCBJ cell is about one order of magnitude longer than that in the front-lit cell, i.e., $5{\times}10^{-4}sec$ vs. $5{\times}10^{-5}sec$. Regardless of substrate thickness up to $150{\mu}m$, the power output in the BCBJ cell stays at nearly the maximum value of about $1.8{\times}10^{-2}W{\cdot}cm^{-2}$, or $18mW{\cdot}cm^{-2}$, as long as the recombination lifetime is $5{\times}10^{-4}s$ or longer. The output power, however, declines steeply to as low as $10mW{\cdot}cm^{-2}$ when the recombination lifetime becomes significantly shorter than $5{\times}10^{-4}sec$. Substrate thinning is found to be not as effective as in the front-lit case in stemming the decline in the output power. In view of these results, for BCBJ applications, the substrate needs to be only mono-crystalline Si of very high quality. This bars the use of poly-crystalline Si, which is gaining wider acceptance in standard front-lit solar cells.

• 한국추진공학회지
• /
• 제12권1호
• /
• pp.57-63
• /
• 2008

공기흡입식 추진 기관인 스크램제트 엔진은 연소기 내부 유동이 초음속으로 유동장의 연소기 내부 체류 시간이 수 ms로 매우 짧다. 이 짧은 시간동안 연소과정이 모두 이루어져야 하므로 초음속 연소기술에 대한 연구는 매우 중요하다. 본 논문은 초음속 연소 기술 중 연료-공기의 혼합을 증대시키는 방법에 관심을 두고 Cavity를 이용한 방법을 선택하여 높이를 10mm로 고정시키고 길이를 변화시켰으며, Cavity 후류에서 지름 1mm의 분사구를 통해 음속 let을 분사시키는 유동장을 형성하여 3차원 Navier-Stokes 방정식을 통해 점성 유동장을 해석하였다. 해석 결과 Cavity 길이/높이비(L/H)가 클수록 Vorticity가 값이 증가하였고 Vorticity의 증가 영역이 유동장의 위, 옆 방향으로 확장되는 것을 볼 수 있었다. 하지만 Vorticity가 증가하는 만큼 추력특성을 떨어뜨리는 정체압력 손실이 증가하므로 연소기 설계 시 최대의 혼합과 최소의 정체압력 손실을 고려한 최적 형상 설계가 필요하다는 것을 확인하였다.

• 비파괴검사학회지
• /
• 제33권1호
• /
• pp.73-79
• /
• 2013

본 실험에서는 NIMAX재료를 3차원 측정기 및 백색광간섭계를 이용, 진원도 측정과 표면조도 측정을 하여 다음과 같은 결과를 얻었다. 절삭특성은 재료의 경도가 큰 관계로 2F의 조건보다 4F의 조건에서 낮게 나타났으며, 주축 회전수 및 공구 이송이 낮을수록 양호하게 나타났다. 3차원 측정기를 통한 진원도 측정은 절삭분력과 같은 4F 조건에서 양호하게 나타났으며, 주축회전수 1,700 rpm, 공구이송속도 85 mm/min의 조건에서 진원도는 양호한 결과를 보였다. 가공면의 표면거칠기는 2F 조건보다 4F의 조건에서 양호하게 나타났으며, 주축회전수 1,700 rpm, 공구이송속도 55 mm/min의 조건에서 Ra $0.4025{\mu}m$값을 보였다.

• 한국레이저가공학회지
• /
• 제14권2호
• /
• pp.8-12
• /
• 2011

As the aged population grows around the world, many medical instruments and devices have been developed recently. Among the devices, a drug delivery stent is a medical device which requires precision machining. Conventional drug delivery stent has problems of residual polymer and decoating because the drug is coated on the surface of stent with the polymer. If the drug is impregnated in micro hole array on the surface of the stent, the problem can be solved. Micro sized holes are generally fabricated by laser machining; however, the fabricated holes do not have an enough aspect ratio to contain the drug or a good surface finish to deliver it to blood vessel tissue. To overcome these problems, we propose a vibration-assisted machining mechanism with PZT (Piezoelectric Transducers) for the fabrication of micro sized holes. If the mechanism vibrates the eyepiece of the laser machining head, the laser spot on the workpiece will vibrate vertically because objective lens in the eyepiece shakes by the mechanism's vibration. According to the former researches, the vibrating frequency over 20kHz and amplitude over 500nm are preferable. The vibration mechanism has cylindrical guide, hollowed PZT and supports. In the cylinder, the eyepiece is mounted. The cylindrical guide has upper and low plates and side wall. The shape of plates and side wall are designed to have high resonating frequency and large amplitude of motion. The PZT also is selected to have high actuating force and high speed of motion. The support has symmetrical and rigid characteristics.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.283-283
• /
• 2011

The n-doping effect by doping metal carbonate into an electron-injecting organic layer can improve the device performance by the balanced carrier injection because an electron ohmic contact between cathode and an electron-transporting layer, for example, a high current density, a high efficiency, a high luminance, and a low power consumption. In the study, first, we investigated an electron-ohmic property of electron-only device, which has a ITO/$Rb_2CO_3$-doped $C_{60}$/Al structure. Second, we examined the I-V-L characteristics of all-ohmic OLEDs, which are glass/ITO/$MoO_x$-doped NPB (25%, 5 nm)/NPB (63 nm)/$Alq_3$ (32 nm)/$Rb_2CO_3$-doped $C_{60}$(y%, 10 nm)/Al. The $MoO_x$doped NPB and $Rb_2CO_3$-doped fullerene layer were used as the hole-ohmic contact and electron-ohmic contact layer in all-ohmic OLEDs, respectively, Third, the electronic structure of the $Rb_2CO_3$-doped $C_{60}$-doped interfaces were investigated by analyzing photoemission properties, such as x-ray photoemission spectroscopy (XPS), Ultraviolet Photoemission spectroscopy (UPS), and Near-edge x-ray absorption fine structure (NEXAFS) spectroscopy, as a doping concentration at the interfaces of $Rb_2CO_3$-doped fullerene are changed. Finally, the correlation between the device performance in all ohmic devices and the interfacial property of the $Rb_2CO_3$-doped $C_{60}$ thin film was discussed with an energy band diagram.

• Journal of Biosystems Engineering
• /
• 제30권2호
• /
• pp.81-88
• /
• 2005

Manual transplanting Chinese cabbage needs 184 hours per ha in Korea. Mechanization of Chinese cabbage transplanting operation has been highly required because it needs highly intensive labor during peak season. This study was conducted to developed walking-type Chinese cabbage transplanter. In order to find out design factor of the transplanter, a kinematic analysis software, RecurDyn, was used. The prototype was tested in the circular soil bin and its operating motion was captured and analyzed using high speed camera system. Prototype was one row type which utilized original parts of engine, transmission and etc. from walking-type rice transplanter in order to save the manufacturing cost. Success ratio of pick-up device of hole-pin type and latch type were $96.0\%$ and $99.2\%$, respectively. which was highly affected by feeding accuracy of feeding device of seedling. Transplanting device of the prototype produced a elliptic loci which were coincident with those produced by the computer simulation. Prototype proved good performance in transplanting with mulching and without mulching operation, either. Working performance of prototype was 22 hours per ha and operation cost of the prototype was 961,757 won per ha. So, it would reduce $88\%$ of the labor and $29\%$ of operation cost.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2013년 춘계학술대회
• /
• pp.19-29
• /
• 2013

Slips and falls are associated with many occupational injuries in Korea. It is also estimated that slipping are major contributors to slip, trip and fall injury burden. So "LOCAL RULE ON OCCUPATIONAL SAFETY AND HEALTH STANDAR D" must be improved, especially article 3(prevention of slip, trip and fall). The primary purpose of the present study is to determine if, and to what extent, the standard could be improved in present environment. In order to fulfill our objective, the another regulation in Korea and foreign countries were investigated and reviewed. Many kind of standard, mandatory documents and guideline were also reviewed. And then, regulations, standard, guideline etc. reviewed were compared with each others. The article 3 was revised as below. 1. The floors of the traffic route in workplace shall have no hole or slope, or be uneven or slippery so as, in each case, to expose employees to slip, trip and fall risk, except if adequate measures have been taken to prevent a employees falling. 2. The employer shall design, install and fix the drain for effective drainage if fluid contaminants were frequently occurred. So far as is reasonably practicable, An employer shall keep the workplace clean, sanitary, and dry so that employees won't have any risk to tripping or slipping at the workplace. 3. To facilitate cleaning, every floor, workplace, and passageway shall be, so far as is reasonably practicable, kept free from protruding objects, splinters, holes, etc. Also, some criteria was developed in this study. Standard and criteria developed in this study will help to prevent slip, trip, and fall injuries.