• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.108-114
• /
• 2010

The injection nozzle of an electro-hydraulic injector is being opened and closed by movement of a injector's needle which is balanced by pressure at the nozzle seat and at the needle control chamber, at the opposite end of the needle. In this study, the effects of needle movement in a piezo-driven injector on unsteady cavitating flows behavior inside nozzle were investigated by cavitation numerical model based on the Eulerian-Lagrangian approach. Aimed at simulating the 3-D two-phase flow behavior, the three dimensional geometry model along the central cross-section regarding of one injection hole with real design data of a piezo-driven diesel injector has been used to simulate the cavitating flows for injection time by at fully transient simulation with cavitation model. The cavitation model incorporates many of the fundamental physical processes assumed to take place in cavitating flows. The simulations performed were both fully transient and 'pseudo' steady state, even if under steady state boundary conditions. As this research results, we found that it could analyze the effect the pressure drop to the sudden acceleration of fuel, which is due to the fastest response of needle, on the degree of cavitation existed in piezo-driven injector nozzle.

• Journal of Korea Society of Industrial Information Systems
• /
• v.17 no.4
• /
• pp.41-50
• /
• 2012

Network life time is very important issue for wireless sensor network(WSN). It is very important to design sensor networks for sensors to utilize their energies in effective ways. A-PEGASIS that basically bases on PEGASIS and enhances in two aspects-an elegant chain generation algorithm and periodical update of chains. However, it has problems in the chain generation mechanism and some possibility of network partitioning or sensing hole problem in the network, in LEACH related protocols. This dissertation proposes a new clustering protocol to solve the co-shared problems in the previous protocols. The basic idea of our scheme is using the table for node connectivity. The results show that the network life time would be extended in about 1.8 times longer than LEACH and 1.5 times longer than PEGASIS-A.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.1
• /
• pp.89-100
• /
• 1994

The current test procedure for transfer length, which determine transfer length by measuring concrete strain, has an actual bond stress state in the prestressed pretensioned member : however, it is difficult to determine the bond properties of maximum bond stress and bond stiffness with this method. It is also difficult for design engineer to understand and select a correct safety criterion from the widely distributed results of such a ransfer test alone. An alternative testing procedure is provided here to determine the bond properties without measuring the concrete strain. In this test the bond stress is measured directly by creating a similar boundary condition within the transfer length in a real beam during the transfer of prestressing force. The prestressing force was released step by step by step from the unloading side. The release of force induces a swelling of the strand at the unloading side of concrete block, bonding force in the block, and a bond slip of the strand toward the other side of the block. Two center-hole load cells are used to record the end loads until the point of general bond slip(maximum bond stress). It is suggested that this test procedure be performed with the ordinary transfer test when determining the transfer length in a prestressed, pretensioned concrete beam.

• Journal of the Korea Convergence Society
• /
• v.11 no.6
• /
• pp.209-213
• /
• 2020

In this study, the model A with the existing shape used at racing car and the model B with light weight were designed. The structural analysis with thermal deformation and stress were carried out. Model A shows that the maximum temperature is lower than model B. The cooling performance due to the shape of the disk without any other cooling conditions can be shown to be better for model A. Model A was seen to be superior in durability as the thermal stress reduced by almost twice as much as model B. The part where the greatest stress occurred appeared to be the hole jointed with the hub regardless of its shape. The analysis results at this study are seen to be useful at designing the shape of the actual vehicle brake disc. The analysis results obtained in this study can be applied at grasping the strength of the brake disk for racing car practically. By utilizing the analysis result of the brake disk for racing car, this study is seen as the convergence study that the aesthetic design and analysis are applied.

• Design & Manufacturing
• /
• v.14 no.2
• /
• pp.62-68
• /
• 2020

Recently, research on precise parts required in aerospace, ship, and automobile industries has been actively conducted. In this paper, electron beam drilling machining parameters were selected and experiments were conducted to compare processing characteristics analysis according to machining parameters through machining experiments of a vaporization amplification sheet to which STS 304 was applied. Also, as a result of measuring the machining. As the thickness gradually increased, it was confirmed that the electron beam could not reach the vaporization amplification sheet and thus melted on the surface of the material. As a result of the experimental analysis, it was analyzed that the vaporization explosion reaction of the vaporization amplification sheet was not normally performed due to the working distance (WD) according to the material thickness.

• Journal of Korean Society of Steel Construction
• /
• v.27 no.1
• /
• pp.1-12
• /
• 2015

Well-designed bolted connections can exhibit excellent ductile behavior through bearing mechanism until the occurrence of bolt shear rupture. The ultimate strength analysis of eccentric bolted connections is an economical and mechanistic approach which uses such ductility. However, the bolt load-deformation relationship, which forms basis of the current practice, is based on very limited combinations of bolt and steel materials. The primary objective of this study was to establish the general bolt force-deformation relationship based on systematic single-bolt bearing connection tests. The test results showed that the projected area of the bolt hole and the strength and thickness of the plate to be connected are the main factors affecting the force-deformation relationship. The results of this study can be used for the instantaneous center of rotation method (ICRM) to achieve more accurate analysis and economical design of a variety of group-bolted connections subjected to eccentric shear.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.3.1-3.1
• /
• 2011

Over the past decade, the major efforts for lowering the cost of electronics has been devoted to increasing the packaging efficiency of the integrated circuits (ICs), which is defined by the ratio of all devices on system-level board compared to the area of the board, and to working on a larger but cheaper substrates. Especially, in flexible electronics, the latter has been the favorable way along with using novel nanomaterials that have excellent mechanical flexibility and electrical properties as active channel materials and conductive films. Here, the tool for achieving large area patterning is by printing methods. Although diverse printing methods have been investigated to produce highly-aligned structures of the nanomaterials with desired patterns, many require laborious processes that need to be further optimized for practical applications, showing a clear limit to the design of the nanomaterial patterns in a large scale assembly. Here, we demonstrate the alignment of highly ordered and dense silicon (Si) NW arrays to anisotropically etched micro-engraved structures using a simple evaporation process. During evaporation, entropic attraction combined with the internal flow of the NW solution induced the alignment of NWs at the corners of pre-defined structures. The assembly characteristics of the NWs were highly dependent on the polarity of the NW solutions. After complete evaporation, the aligned NW arrays were subsequently transferred onto a flexible substrate with 95% selectivity using a direct gravure printing technique. As proof-of-concept, flexible back-gated NW field effect transistors (FETs) were fabricated. The fabricated FETs had an effective hole mobility of 0.17 $cm2/V{\cdot}s$ and an on/off ratio of ${\sim}1.4{\times}104$. These results demonstrate that our NW gravure printing technique is a simple and effective method that can be used to fabricate high-performance flexible electronics based on inorganic materials.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.11
• /
• pp.1367-1372
• /
• 1988

In this paper, we have optimized the computation of the CSP - LOC (Channel Substrate Planar-Large Optical Cavity) structure to design the gith power (Ga, Al) As/GaAs CSP-LOC laser diode. The parameters of the device on the bases of experimental datas include the effects of the various layer thickness, material absorption coefficients, stripe width and so forth. At active layer ($d_2$)=0.08 um with optical layer ($d_3$)=0.5 um and $d_2$ = 0.1 um with $d_3$ = 0.4 um, we find the narrower beam divergence and stable high power in the lowest-order mode without the phenomenon of spatial hole burning. The results of theoretical computation show good agreement with experimental measurements made on LPE grown CSP-LOC. Finally, we developed an practical program and the program is applicable to the CSP-LOC lasers with any materials.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.1206-1215
• /
• 2008

In this study, the equivalent pressure acting on the face of drilled hole was determined by back analysis. This analysis was continued until the difference between the displacement directly measured during field test construction of CGS and the displacement evaluated by numerical analysis was below 10 percent, and the affect of diaphragm wall adjacent to grout bulb was evaluated by numerical analysis using the equivalent pressure. From the analysis results, it was observed that the increase of the pressure acting on the diaphragm wall was greater at reclaimed sandfill layer than silty clay layer during the installation of CGS. Two methods were adopted to reduce the pressure acting on the diaphragm wall. One is installing of trench between diaphragm wall and grout bulb, the other is pre-installing of CGS before construction of diaphragm wall. From the numerical analysis results, above two methods can be considered as an effective method to reduce the pressure. It was analyzed that the amount of reduction of the pressure and the displacement are 689.8% and 564.6%, respectively, in the case of adopting the trench method, and 463.7% and 214.0%, respectively, in the case of adopting pre-installing of 3 columns CGS.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.1
• /
• pp.80-83
• /
• 2017

In this paper, the X-band reconfigurable frequency selective surface having flexible geometry was proposed. The proposed RFSS is composed of patterns of cross-shaped loop with inductive stub, which can control the frequency response for C-Band and X-band by ON/OFF state of PIN diode. To minimize the parasitic effect and to obtain the high level of isolation between the unit cell of FSS and the bias circuit, we designed the grid type bias line on bottom layer through via hole. The measured transmission characteristics show good agreement with the simulation results and good stability of frequency response for different incident angles and curvatures of surface.