• International Journal of Highway Engineering
• /
• v.16 no.1
• /
• pp.57-62
• /
• 2014

PURPOSES : Capacity is a main factor of determining the number of lane in highway design or the level of service in road on operation. Previous studies showed that breakdown may occur before capacity is reached, and then it was concluded that capacity is a stochastic value rather than a deterministic one. In general, estimating capacity is based on average over maximum traffic volume observed for capacity state. This method includes the empirical distribution method(EDM) and would underestimate capacity. This study estimated existing empirical methods of estimating stochastic highway capacity. Among the studied methods are the product limit method(PLM) and the selected method(SM). METHODS : Speed and volume data were collected at three freeway bottleneck sites in Cheonan-Nonsan and West Sea Freeway. The data were grouped into a free-flow state or capacity state with speeds observed in the bottlenecks and the upstream. The data were applied to the empirical methods. RESULTS : The results show that the PLM and SM estimated capacity higher than EDM. The reason is that while the EDM is based on capacity observations only, the PLM and SM are based on free-flow high volumes and capacity observations. CONCLUSIONS : The PLM and SM using both free-flow and capacity observations would be improved to enhance the reliability of the capacity estimation.

• Journal of the Korean Society of Safety
• /
• v.11 no.4
• /
• pp.122-126
• /
• 1996

In this thesis, the field test results of fifty-one highway bridges were analyzed in order to Investigate the primary capacity of load of highway bridges. From this study, it was known that primary capacity of load are decreased with the serviced years, and those are small in T-beam bridges rather than I-beam bridges. And the average primary capacity of load of highway bridges is seemd about 15. 5ton in T-beam bridges and in I-beam bridges about 19.7ton.

• International Journal of Highway Engineering
• /
• v.14 no.6
• /
• pp.167-173
• /
• 2012

PURPOSES : This study is to develop speed correction factor for more realistic Level-of-Service(LOS) at multilane highway. METHODS : In this study, we compared speed difference the degree of speed reductions in actual multilane road conditions with speed reduction considering speed correction factor presented in highway capacity manual using statistical techniques. And also we presents new speed correction factor analyzing collected data at national highway No.1 (Goyang~Wolrung). RESULTS : The result of analyzing and comparing new suggested speed correction factor with speed correction factor in Korea Highway Capacity Manual (KHCM) shows RMSE (Root Mean Square Error) in new speed correction factor (RMSE 1.5) is much lower than existing speed correction factor (RMSE 13.4). New suggested speed correction can be used for analyzing Level-of-Service at multilane highway. And also we suggests improvements for analysis procedure in analyzing Level-of-Service at multilane highway CONCLUSIONS : As a result of comparing differences, we draw the causes that effect the differences in speed and suggest new speed correction factor that consider traffic volumes. It can be more rational because it uses speed correction factor which can consider more realistic traffic conditions, etc.

• Proceedings of the KOR-KST Conference
• /
• 1999.10a
• /
• pp.197-202
• /
• 1999

• International Journal of Safety
• /
• v.9 no.2
• /
• pp.16-21
• /
• 2010

In this study, the variations of transformed impact factors and load carrying capacity of highway bridges measured from the state of expansion joint are evaluated. the field loading tests were performed on the highway bridge with damaged expansion joint to investigate the variation of the load carrying capacity. From the field loading tests in case that damaged expansion joint exist or do not exist, the static displacements and dynamic displacements were measured, and TIF were calculated, respectively. dynamic test is performed in order to estimate dynamic displacement and TIF according to the level of damage of expansion joint. From the results of TIF, the load carrying capacity of highway bridges with damaged expansion joint were estimated.

• Journal of the Korean Society of Safety
• /
• v.27 no.6
• /
• pp.138-143
• /
• 2012

In this thesis, the relationship between the load carrying capacity and the transformed impact factor of the highway bridges were studied. The bridges are classified according to superstructures type. The result of the comparison between the load carrying capacity and the transformed impact factor, if the load capacity ratio of 0.57, the transformed impact factor was less in order of RC T-beam bridge, RC slab bridge, PC beam bridge, I-beam bridge. By the regression analysis on these results, the empirical formulae to predict the the load carrying capacity of bridge were suggested.

• Journal of Korean Society of Transportation
• /
• v.27 no.3
• /
• pp.141-148
• /
• 2009

An inappropriate evaluation of capacity leads to the incorrect and impractical result due to the transfer of error to the analysis and the evaluation on highway system. The traffic accident which reduces the capacity of road temporarily generates unpredictable congestion, causing difficulties in congestion management. Therefore, this research aims on the measurement of the capacity of the road in accordance to the speed at the accident which is a basic factor when performing analysis. Based on the given approach, the behavior of a vehicle in highway is understood to develop model of critical gap and model of maximum flow rate with respect to the speed of traffic flow. With the established model, the reduction rate of the capacity in highway system at the accident is measured. The result shows that the capacity is reduced by 37% when the speed of the traffic flow is 40km/h. Although the developed model can't be verified clearly, this research has shown that the reduction rate of the capacity in road system has a close relation to the speed.

• Journal of Korean Society of Transportation
• /
• v.11 no.1
• /
• pp.23-36
• /
• 1993

The two-lane, two-way highway simulation program(TWOPAS) is evaluated for Korean Highway Capacity Manual Study. TWOPAS program input variables, especially related vehicle performance, traffic flow relationship, car-following model and passing logic are examined and modified through the analysis results of our two-lane, two-way highway traffic characteristics. Simulation outputs with and without modification are compared with the field data. The results show that improved TWOPAS program(TWOPAS KI) is well suitable for simulating our two-lane, two-way highway condition.

• International Journal of Highway Engineering
• /
• v.17 no.4
• /
• pp.107-115
• /
• 2015

PURPOSES: This study analyzes the characteristics of traffic flow on freeway sections under daytime and nighttime conditions to improve traffic safety, and suggests a method to estimate an accurate freeway capacity value that reflects these characteristics. METHODS : The trends and differences in capacity were investigated using comprehensive field data collected under both daytime and nighttime conditions on freeway sections with designated speeds of 80, 100, and 120 kph. RESULTS : The capacity values under nighttime driving conditions were reduced by 3.3%, 6.9%, and 8.8% at 80, 100, and 120 kph, respectively. Several nighttime adjustment factors were deduced for each designated speed category from the analysis results. CONCLUSIONS : It is expected that more accurate capacity values can be estimated for freeway sections under nighttime conditions by applying the resulting adjustment factors. In addition, traffic safety will be improved through the increased efficiency of traffic management on these freeway sections.

• International Journal of Highway Engineering
• /
• v.15 no.1
• /
• pp.37-45
• /
• 2013

PURPOSES: This study is to analyze different vehicle load effects for a bridge design of South and North Korea in order to prepare a common design specification and to secure the safety of transportation when the highway bridges of South and North Korea use together. METHODS: Based on the literature review, this study considers vehicle load effects by comparing different characteristics of the standard vehicle and other differences of the bridge design specification between South and North Korea. And structural modeling of three-span continuous PSC Beam Bridge are analyzed and the bridge capacity according different vehicle loads of South and North Korea is evaluated. RESULTS: The result of this study indicates that the bridge capacity and the design vehicle weight of North Korea are smaller than the bridge capacity and the design vehicle weight of South Korea. Also this study demonstrates that the design vehicle array and other characteristics of North Korea are very different than the design vehicle array and other characteristics of South Korea. CONCLUSIONS: It is expected that the outcomes of this study can be useful in the set-up of South-North Bridge Specification because similar previous studies are rarely found.