• Journal of Radiation Protection and Research
• /
• v.24 no.2
• /
• pp.73-86
• /
• 1999

The ion-exchange method for the purification of primary coolant has been used broadly in PWR(pressurized water reactor)-type nuclear power plants due to its high decontamination efficiency, simple system, and easy operation. However, its non-selective removal of metal and non-radionuclides shortens its life, resulting in the generation of a large amount of waste ion-exchange resin. In this study, the feasibility of electrodeionization (EDI) was investigated for the purification of primary cooling water using synthetic solutions under various experimental conditions as an alternative method for the ion exchange. The results shows that as the feed flow-rate increased, the removal efficiency increased and the power consumption decreased. The removal rate was observed as a 1000 decontamination factor(DF) at a nearly constant level. For the synthetic solution of 3 ppm TDS (Total Dissolved Solid), the power consumption was 40.3 mWh/L at 2.0 L/min of feed flow rate. The higher removal rate of metal species and lower power consumption were obtained with greater resin volume per diluting compartment. However, the flow rate of the EDI process decreased with the elapsed time because of the hydrodynamic resistivity of resin itself and resin fouling by suspended solids. Thus, the ion-exchange resin was replaced by an ion-conducting spacer in order to overcome the drawback. The system equipped with the ion-conducting spacer resolved the problem of the decreasing flow rate but showed a lower efficiency in terms of the power consumption, the removal rate of metal species and current efficiency. In the repeated batch operation, it was found that the removal efficiency of metal species was stably maintained at DF 1000.

• Culinary science and hospitality research
• /
• v.20 no.4
• /
• pp.127-143
• /
• 2014

This study investigated color barley powder substituted for wheat flour in bread recipes with the amounts of 0%, 5%, 10%, 15% and 20%. Color barley powder consisted of 9.35% of moisture content, 9.37% of crude protein, 1.64% of crude fat and 2.96% of crude ash. Water soluble dietary fiber is 3.21, insoluble dietary fiber is 4.91, total dietary fiber content is 8.12, and ${\beta}$-glucan is 49.31. DPPH radical scavenging activity is 56.76%, total phenol content is 234.34. The farinograph measurement result of the bread made with color barley powder showed that consistency, water absorption, development time and time breakdown have decreased. The alveogram measurement result of the bread made with color barley powder showed that overpressure, extensibility, swelling index and deformation energy have increased. The amylograph measurement result of the bread made with color barley powder showed that peak viscosity, hot past viscosity and breakdown have decreased. Baking loss and specific loaf volume have decreased as the color barley powder content increased. The chromaticity measurement result showed that the 'L' and 'b' of bread have increased as the color barley powder content increased, while the chromatic 'a' value increased. The texture measurement result showed that the hardness and gumminess of bread have increased as the color barley powder content increased. cohesiveness, springiness and chewiness have decreased. Overall preference scores showed a high overall acceptability for the bread made with 10% color barley powder.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.20
• /
• pp.9009-9013
• /
• 2014

Background: The aim of this study was to explore the efficacy and adverse reactions of CT-guided radioactive 125I-seed implantation treatment combined with chemotherapy for platinum-resistant recurrent ovarian carcinoma. Materials and Methods: From September 2010 to December 2012, 23 patients with platinum-resistant recurrent ovarian carcinoma were enrolled. All the patients refused, could not bear, or were not suitable for surgery. They all had no more than 3 lesions, which were detected and could also be measured by CT. All were clarified as single-lesion or multiple-lesion groups. A total of 41 lesions underwent implantation of from 8 to 106 125I seeds (median=43). Multi-plane implanting was adopted and 125I-seeds of (0.4-0.7)mCi were placed at intervals of (0.5-1.0) cm. After implantation treatment, all patients underwent 4 cycles of chemotherapy with gemcitabine $800mg/m^2$ (days 1, 8 and 15). Results: The outcome was evaluated with CT 3 weeks and every 3 months after implantation treatment. After 6 months, the volume of 32 out of 41 lesions (78.0%) was reduced at least 30%, within which 9 lesions completely disappeared(22.0%). Complete response was observed in 7 cases (30.4%), with a partial response in 4 cases (17.4%), 4 cases stable(17.4%)and 8 cases showing progression (34.8%). The total clinical remission rate was 47.8% (11/23). The clinical remission rate was 77.8% (7/9) in the single-lesion group and 28.6% (4/14) in the multiple-lesion group with a significant difference between the two(P=0.036). The common side effects observed were mild gastrointestinal reactions. Conclusions: 125I-seed implantation combined with chemotherapy applies an effective way in the treatment of platinum-resistant recurrent ovarian epithelial carcinoma with the advantages of high local control rates, good short-term effects, little trauma and less side effects.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.sup3
• /
• pp.81-85
• /
• 2016

Globally, the burden of breast cancer (BC) continues to increase. BC related lymphedema (BCRL) is currently non curable and as a life time risk it affects at least 25% of BC patients. Knowing more about BCRL and appropriate control of its modifiable risk factors can improve quality of life (QOL) of the affected patients. In this case control study to detect factors, 400 women with BCRL (as the case group) and 283 patients with BC without lymphedema (as the control group) that were referred to Shiraz University of Medical Sciences affiliated BC clinic center were assessed. The data were analyzed in SPSS. The mean age of the case group was $52.3{\pm}11.0years$ and of the control group was $50.1{\pm}10.9years$. In patients with BCRL, 203(50.7%) had left (Lt) side BC and in non- lymphedema group 151 (53.3%) had Lt side BC. Out of all BCRL patients, 204 (51%) had lymphedema in all parts of their affected upper extremities, 100 (25%) had swelling in the arm and forearm and 23 (5.7%) had edema in both the upper extremity and trunk. Edema, heaviness, concern about changing body image, pain and paresthesia were the most common signs/symptoms among patients with BCRL. In BCRL patients, the difference of circumference between the affected upper limb and non-affected limb was $4.4{\pm}2.5cm$ and the difference in volume displacement was $528.7{\pm}374.4milliliters$. Multiple variable analysis showed that moderate to severe activity (OR; odds ratio =14, 95% CI :2.6-73.3), invasiveness of BC (OR =13.7, 95% CI :7.3-25.6), modified radical mastectomy (OR=4.3, 95% CI :2.3-7.9), BMI =>25 (OR=4.2, 95% CI :2-8.7), radiotherapy (OR=3.9, 95% CI :1.8-8.2), past history of limb damage (OR=1.7, 95% CI :0.9-3.1) and the number of excised lymph nodes (OR=1.06, 95% CI :1.02-1.09) were the significant predictors of lymphedema in women with BC. Modifiable risk factors of BCRL such as non-guided moderate to severe physical activity, high BMI and trauma to the limb should be controlled as early as possible in BC patients to prevent development of BCRL and improve QOL of these patients.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.911-917
• /
• 2015

The objective of this work focuses on the analysis of injection rate and macroscopic spray behavior characteristics with injection pressures as well as combustion and exhaust emission characteristics with injection timing and injection pressure by using a common rail single-cylinder diesel engine. The injection rate was measured by applying the Bosch method, and macroscopic spray behavior characteristics were analyzed with a constant-volume vessel and a high-speed camera. In addition, combustion and emission characteristics were analyzed in a common-rail single-cylinder diesel engine with precise control of fuel injection timing and pressure. For injection pressures of 30MPa and 50MPa, the injection rate was higher at 50 MPa, and the spray development (penetration) was also higher in the same elapsed time. The peak in-cylinder pressure and rate of heat release showed a tendency to decline as injection timing was delayed, and the peak in-cylinder pressure and rate of heat release were slightly higher for higher injection pressures. Higher injection pressures also reduced the mean effective pressure, while the indicated mean effective pressure and torque increased as injection timing was delayed to TDC. Nitrogen oxides had a peak level at injection timings of $BTDC20^{\circ}$(30MPa) and $BTDC15^{\circ}$(50MPa); carbon monoxide emissions were reduced by delaying injection timing from $BTDC30^{\circ}$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.1
• /
• pp.96-101
• /
• 2017

We have developed a compact desktop-sized nanopatterning system driven by the Roll-to-Roll (R2R) nanoimprinting (NIL) principle. The system realizes the continuous and high-speed stamping of various nanoscale patterns on a large-area flexible substrate without resorting to ponderous and complicated instruments. We first lay out the process principle based on continuous NIL on a UV-curable resin layer using a flexible nanopatterned mold. We then create conceptual and specific designs for the system by focusing on two key processes, imprinting and UV curing, which are performed in a continuous R2R fashion. We build a system with essential components and optimized modules for imprinting, UV curing, and R2R conveying to enable simple but effective nanopatterning within the desktop volume. Finally, we demonstrate several nanopatterning results such as nanolines and nanodots, which are obtained by operating the built desktop R2R NIL system on transparent and flexible substrates. Our system may be further utilized in the scalable fabrication of diverse flexible nanopatterns for many functional applications in optics, photonics, sensors, and energy harvesters.

• Journal of Mushroom
• /
• v.4 no.4
• /
• pp.135-143
• /
• 2006

We have investigated cultural circumstance and given condition of king oyster mushroom(Pleurotus eryngii) growing farmer. We collected many pathogens from King oyster mushroom growing farmer and identified with chemicobiological test and microscope. Most of investigated farmers neglected their's growing room cleaning and washing, after harvesting At pin-heading induction time, humidity degree in growing room was kept of high level and Air ventilation volume was so little that fruit-body formation ratio was low. The collected pathogens were twenty eight strains and identified with Pseudomonas sp., Trichoderma sp. mostly. During the spawn running time and pin-heading induction time, contamination by Trichoderma sp. occurred mostly, but during the fruit-body growing time, contamination by Pseudomonas sp., Erwinia sp. etc, occurred.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.5
• /
• pp.2717-2722
• /
• 2013

Background: The objective of this research is the computed axial tomography (CT) imaging grading of radiation induced pneumonitis (RP) and its correlation with clinical and radiotherapeutic parameters. Materials and Methods: The chest CT films of 20 patients with non-small cell lung cancer who have undergone threedimensional conformal radiation therapy were reviewed. The proposed CT grading of RP is supported on solely radiological diagnosis criteria and distinguishes five grades. The manifestation of RP was also correlated with any positive pre-existing chronic obstructive pulmonary disease (COPD) history, smoking history, the FEV1 value, and the dosimetric variable V20. Results: The CT grading of RP was as follows: 3 patients (15%) presented with ground glass opacity (grade 1), 9 patients (45%) were classified as grade 2, 7 patients (35%) presented with focal consolidation, with or without elements of fibrosis (grade 3), and only one patient (5%) presented with opacity with accompanying atelectasis and loss of pulmonary volume (grade 4). Both univariate and multivariate analysis revealed as prognostic factors for the radiological grading of RP the reduction of FEV1 and the V20 (P=0.026 and P=0.003, respectively). There was also a significant (P<0.001) correlation of radiological grading of RP with FEV1 and V20 (spearman rho 0.92 and 0.93, respectively). Conclusions: The high correlation of the proposed radiological grading with the FEV1 and the V20 is giving a satisfactory clinical validity. Although the proposed grading scale seems relevant to clinical practice, further studies are needed for the confirmation of its validity and reliability.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.181-186
• /
• 2020

This study examined the artificial fertilization efficiency of crossbred goats from a farmhouse using frozen semen. Electrostimulation was used to ejaculate and collect semen to assess the artificial fertilization efficiency of crossbred goats. The sperm concentration, vitality, and vitality after melting were investigated. The sperm volume was within 2.5~3 ml, and the concentration was 21~25 × 10⁸/ml for each male crossbred goat. The melted semen had high vitality (≥90%). An IDEXX Rapid Visual Pregnancy Test kit was used for an earlier diagnosis of the pregnancy and to determine the pregnancy rate of fertilization using frozen-thawed semen. The reproductive performance of the artificially fertilized crossbred goats had the highest delivery rate (68%) from Farm C and the lowest delivery rate (45%) from farm A. The delivery rate through artificial fertilization was equal to the fertilization rate according to early pregnancy diagnostic kits. The artificial insemination efficiency was 45~68%. These findings can be used as the basis for improvement and breeding goats in goat farms and livestock research institutes.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.23 no.5
• /
• pp.392-399
• /
• 2013

Due to the development of IT technology and the information age, a dependency of the network over the most of our lives have grown to a greater extent. Although it provides us to get various useful information and service, it also has negative effectiveness that can provide network intruder with vulnerable roots. In other words, we need to urgently cope with theses serious security problem causing service disableness or system connected to network obstacle with exploiting various packet information. Many experts in a field of security are making an effort to develop the various security solutions to respond against these threats, but existing solutions have a lot of problems such as lack of storage capacity and performance degradation along with the massive increase of packet data volume. Therefore we propose the packet analysis model to apply issuing Big Data technology in the field of security. That is, we used NoSQL which is technology of massive data storage to collect the packet data growing massive and implemented the packet analysis model based on K-means clustering using MapReudce which is distributed programming framework, and then we have shown its high performance by experimenting.