• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.420-423
• /
• 2009

In this study, the guideline for designing the drawbeads used in the stamping dies for advanced high strength steel (AHSS) sheets is investigated. In the drawbead drawing test, the drawbead forces for verifying the equivalent drawbead model(EDM) and the sheet strains for finding marginal strains from $FLC_0$ are measured. In the finite element analysis (FEA), the bending allowance, R/t, is obtained. Based on the forming and bending allowances obtained, the design guideline of the drawbead for determining height and width, which depends on the restraining force and the forming allowance, is prepared by using EDM.

• 소성∙가공
• /
• 제18권1호
• /
• pp.39-44
• /
• 2009

This paper is concerned with forming technology of an automotive front side member part with ultra high strength steel sheet of DP980. The forming technology considered in this paper is the draw & form type, which installs the upper pad and lower pad to produce the complicated shape of ultra high strength steel sheet. In order to produce sound product, comparison between form type and draw & form type and between draw type and draw & form type are investigated by FE-analysis. FE-analysis is carried out with commercial sheet metal forming analysis S/W, DYNAFORM. It was shown from FE-analysis that the draw & form type satisfied the required specifications such as the dimensional accuracy and soundness of automotive front side member part. The effectiveness of the analytical result was verified by the experiment. From this investigation, the draw & form type is proved to be able to supply useful forming technology in forming ultra high strength steel.

• 소성∙가공
• /
• 제25권5호
• /
• pp.301-305
• /
• 2016

The manual modification of stamping die has widely been used in order to reduce springback after sheet metal forming. When UHSS (Ultra High Strength Steel) is used in sheet metal forming, the die design considering springback compensation is more difficult because higher strength sheet has more springback. In this study, the optimization method was used in order to design die geometry considering springback compensation after forming of 1.2GPa UHSS. Die geometries were defined as design variables and the springback distance from the die surface was conducted as object function in optimization process. The optimized die geometry considering springback compensation was performed using finite element and optimization analysis. The simulation results such as thickness distribution and springback amount were compared with measured data using 3D optical measurement system (GOM ARGUS, ATOS). And the prediction of springback amount showed a good agreement within test results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.238-243
• /
• 2007

This paper is designed to estimate the adhesion strength of coating layer on galvannealed steel sheet using lap shear test. The single lap shear test is the most commonly used standard test for determining the strength of medium-strength and high strength bonds. The bond strength of bonded single lap joints on subjecting the substrates to loads is determined by lap shear forces in the direction of the bonded joint. In this study, specimen for adhesion strength test was made to attach coated sheet to cold rolled sheet and were heated in temperature of 180 for 20minutes. After test, detached parts of coatings on coated sheet were observed using SEM and EDX to identify substrate and complete detachment. The tested results showed that adhesive strength of coating is unrelated to anisotropy of sheet and is difficult to be extracted using conventional theory because of fine cracks of coating layers which were created during annealing process.

• 대한금속재료학회지
• /
• 제50권1호
• /
• pp.8-12
• /
• 2012

This study aims to analyze the formability property of surface texturing processed automotive steel sheet for improving the sheet forming property. In the paper, the effect of cavities fabricated using the laser surface texturing technique on automotive high strength steel sheets was studied. The frictional behavior of the sheet drawing is a function of interface parameters such as sheet surface roughness, holding force, contact pressure, etc. For these reasons, automotive steel researchers want to optimize the surface topography of automotive steel sheets in order to enhance the formability. Therefore, this study presents the behavior of deformation of a laser surface texturing steel sheet by considering the frictional operation during the deep drawing process.

• 소성∙가공
• /
• 제30권5호
• /
• pp.236-241
• /
• 2021

This study describes the cold stamping process design procedure to secure the formability and dimensional accuracy of the automotive structural component fabricated by 1.5GPa grade ultra-high strength steel sheet. The target product is selected as the front side rear lower member which is the most important energy absorption part in the frontal impact condition. To secure the product quality, an intermediate product shape is added while considering the low elongation and high strength characteristics of 1470Mart. The sequential optimization procedure of the intermediate product shape, the fine dimensional quality is then achieved without any crack or wrinkling. The cold stamping method with ultra-high strength steel sheets is validated by conducting the die tryout of the front side rear lower member.

• 열처리공학회지
• /
• 제12권3호
• /
• pp.231-239
• /
• 1999

Volume fraction and morphology of retained austenite, tensile properties of TRIP type high strength steel sheet with Fe-C-Si-Mn-Cu chemical composition have been investigated. The retained austenite of granular, bar and film type existing in specimen was obtained after intercritical annealing and austempering. The granular type retained austenite increased with increase of intercritical annealing and austempering temperature. With increase of intercritical annealing temperature, retained austenite and carbon contents increased. Maximum contents of retained austenite was obtained by austempering at $400^{\circ}C$. The maximum tensile strength was obtained by austempering at $450^{\circ}C$ and maximum elongation was obtained at $400^{\circ}C$. T.S${\times}$E.L value increased with increase of retained austenite contents due to the elongation strongly controlled by contents of retained austenite, but tensile strength was affected with various factors such as bainitic structure etc.

• 한국자동차공학회논문집
• /
• 제15권1호
• /
• pp.171-176
• /
• 2007

An important challenging issue in the automotive industry is the light-weight, safe design and enhancement of crash response of an auto-body structures. These objectives lead to increasing adoption of high strength steel sheet for inner and outer auto-body members. This paper evaluates the dynamic tensile characteristics of high strength steel sheets, HS45R, TRIP60, DP60 and DP100, along the rolling direction and transverse direction. Static tensile tests were carried out at the strain rate of 0.003/sec using the static tensile machine (Instron 5583). Dynamic tensile tests were carried out at the range of strain rate from 0.1/sec to 200/sec using a high speed material testing machine developed. The tensile tests acquire stress-strain relation and strain rate sensitivity of each material. The experimental results show two important aspects for high strength steels: the flow stress increases as strain rate increases; the strain hardening decreases as the tensile stress increases. The experiments also produce interesting results that the elongation does not decrease even when the strain rate increases.

• 대한기계학회논문집
• /
• 제13권2호
• /
• pp.229-235
• /
• 1989

본 연구에서는 편면도금 강판과 복합조직 고장력 강판간의 이종 용접재의 피로거동을 연구하고져 한다. 즉 유한요소법으로 응력분포를 조사하고 그 결과와 피로균열발생 위치를 비교 검토해 보고자 한다.

• 대한기계학회논문집A
• /
• 제34권8호
• /
• pp.997-1006
• /
• 2010

차체 경량화를 위해 알루미늄과 같은 경량금속의 사용은 이종소재 사용은 새로운 접합기술을 요구한다. 클린칭 접합은 이종소재 접합기술 중의 하나로 접합소재의 강도차이에 의해 접합특성이 달라진다. 본 연구에서는 Al5052 합금소재에 대한 고장력강판(SPFC440, 590, 780)에 대한 클린칭 접합특성을 평가하였다. 유한요소해석과 인장전단시험을 통해 클린칭 접합특성인 클린칭 접합의 기학적 구속량과 접합강도를 평가하였다. 상부소재가 고장력강판인 경우, SPFC780 은 상부소재의 네킹으로 클린칭 접합이 불가능하였다. 또한 상부소재의 강도가 증가함에 따라 접합강도가 증가하는 특성을 나타내었다. 하부소재가 고장력강판인 경우, 기하학적 구속량인 목두께 및 언더컷과 접합강도는 하부소재의 강도가 증가함에 따라 감소하는 경향을 나타내었다.