• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.670-674
• /
• 2004

High-speed trains with the maximum speed of 300 km/h have started revenue services since April 2004. A large portion of the 'Kyung- Bu' line is comprised of tunnels or bridges, which may cause excessive noise in a vehicle. The vibration generated by the trains propagates into the structure of the tunnel and the vehicle and it can be radiated as noise inside the vehicle interior. This noise can usually be heard as low frequency structure-borne noise. Measurement of the noise and vibration inside the KTX vehicle confirmed that the noise comprises of frequencies below 250 Hz with a couple of broad peaks.

• 자동차안전학회지
• /
• 제7권2호
• /
• pp.50-54
• /
• 2015

Rollover accidents are a common occurrence on the highway ramp section. At highway ramp section, unexpected situations might occur due to demand on complex steering control unlike routine driving maneuver in the main streamline. Commercial vehicles have higher risk of rollover due to their high center of gravity. In this study, the lateral acceleration causing rollover would be found. In addition, sections would be classified as dangerous and safe ones by confirming the maximum lateral acceleration for various speed and curvature.

• 한국철도학회논문집
• /
• 제13권1호
• /
• pp.51-57
• /
• 2010

본 연구에서는 진공튜브 내 초고속열차의 공기저항을 전산유체역학을 이용하여 계산하였으며, 튜브-열차 시스템의 주요 시스템 파라메타인 열차 속도, 공기밀도, 터널 직경을 변화시켜가면서 공기저항의 변화를 살펴보았다. 튜브 내에서의 열차 공기저항은 속도의 제곱보다 더 급격히 증가하며, 튜브 직경이 증가함에 따라 감소하는 경향을 보였으며, 공기밀도가 감소함에 따라 개활지와 마찬가지로 거의 선형적으로 감소하는 특성을 보여주었으며, 특정 파라메타 공간에 대하여 파라메타에 따른 공기저항 변화의 불규칙성이 다소 나타났다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.960-964
• /
• 2011

High speed railway structure, contact of vehicle needs to design considering the running stability(dynamic behavior). Also, upper structure has to satisfy design standard about moving load, high speed train(KTX). So, the high speed railway structure has to satisfy the requirement of natural frequency, vertical acceleration on deck, face distortion and vertical displacement considering ride comfort, which is suggested Ho-nam high speed railway design standard. In this study, it was investigated and evaluated to the dynamic behavior for tow plate Girder railway bridge subjected to moving load considering real high speed train loads.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1138-1142
• /
• 2010

High speed railway structure, contact of vehicle needs to design considering the running stability(dynamic behavior). Also, upper structure has to satisfy design standard about moving load, high speed train(KTX). So, the high speed railway structure has to satisfy the requirement of natural frequency, vertical acceleration on deck, face distortion and vertical displacement considering ride comfort, which is suggested Ho-nam high speed railway design standard. In this study, it was investigated and evaluated to the dynamic behavior for a double-rib arch railway bridge subjected to moving load considering real high speed train loads.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.1154-1159
• /
• 2008

Type of the high-speed train under development has been decided to be EMU(electric multiple Units) following the trend of the times, which is weak for vibration and noise due to the distributed traction unit of motors and gears than that of the articulated high-speed train. Also, passengers may feel uncomfortable at high-speed running due to the various vibration of vehicle itself and bogie, especially due to hunting, snake motion of the high-speed train. In this paper, explained was the program to develop the high-speed EMU at every step of basic and detail design and running test, predict and try to reduce the vibration.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.58-64
• /
• 2007

As the concerns regarding global worming were increased, the pressure of greenhouse gas(GHG) emission reduction on mobile source was also increased. Carbon dioxides contribute over 90% of total GHG emission and the mobile source occupies about 20% of this $CO_2$ emission. Therefore automotive exhaust is suspected to be one of the major reasons of the rapid increase in greenhouse effect gases in ambient air. In this study, in order to investigate $CO_2$ emission characteristics from gasoline passenger cars(PC), which is the most dominant vehicle type in Korea, 106 vehicles were tested on the chassis dynamometer. $CO_2$ emissions and fuel efficiency were measured. The emission characteristics by displacement, gross vehicle weight, vehicle speed and CVS-75/vehicle speed mode were discussed. Test modes were vehicle speed modes and CVS-75 mode that have been used to develop emission factors and to regulate for light-duty vehicle in Korea. It was found that $CO_2$ emissions showed higher large displacement, heavy gross vehicle weight, low vehicle speed and CVS-75 mode than small displacement, light gross vehicle weight, high vehicle speed and vehicle speed mode, respectively. From these results, correlation between $CO_2$ emission and fuel efficiency was also determined. The results of this study will contribute to domestic greenhouse gas emissions calculation and making the national policy for climate change.

• 대한토목학회논문집
• /
• 제30권1D호
• /
• pp.1-10
• /
• 2010

고속도로 영업소의 경우 하이패스차량과 일반TCS이용차량간의 혼용 및 차로변경으로 인한 상충이 발생하는 구간으로 안전성에 대한 검토가 필요한 구간이다. 본 연구에서는 영업소 진출부에 설치된 중앙하이패스 이용차량과 일반차로 이용차량간의 상충 및 사고위험성을 현장비디오촬영 및 상충분석을 통해 알아보았다. 차량속도와 상대속도 및 상충으로 인한 차량 감속시간 등을 분석한 결과 하이패스이용차량과 일반TCS이용차량간의 상대속도가 클수록 상충으로 인한 차량 급감속이 발생한다는 문제점을 파악하였으며, 중앙 하이패스 설치시 상충 발생 위치 및 차로 운영형태에 따라 상충빈도 및 상대속도가 다름을 확인할 수 있었다. TA(Time to Accident)분석 결과, 고속도로 영업소 중앙 하이패스 설치시 차량간 상대속도, 상충위치 및 빈도에 따른 상충시 하이패스 차량의 급감속 및 감속시간이 큼에 따라 사고위험이 높은 것으로 분석되었다. 또한 합류 시점부가 영업소 진출부와 가까울수록 TA분석값이 낮은 것으로 분석되어 전반적으로 속도차이를 줄여 안전성을 증대시켜야 함을 알 수 있었다. 본 연구에서는 영업소 진출부 중앙 하이패스 설치로 발생하는 상대속도차에 의한 상충으로 급감속 및 사고를 억제함으로서 영업소 중앙 하이패스 차로 설치시 안전성을 높여줄 수 있을 것으로 기대된다.

• 한국산학기술학회논문지
• /
• 제19권11호
• /
• pp.350-356
• /
• 2018

팬터그래프(Pantograph)와 전차선간의 동적 상호작용인 접촉력(contact force)은 차량에 대한 안정적 전원공급 특성인 집전성능을 평가하는 중요한 지표이다. 본 연구에서는 동력분산형 고속열차 시험차량인 HEMU-430X(High-speed Electric Multiple Unit - 430km/h eXperiment) 차량의 팬터그래프 동적 접촉력 특성을 전차선 장력에 따라 분석하였고, 이를 팬터그래프-전차선 동적 상호작용 모델을 이용한 해석결과와 비교하였다. 시험결과와 해석결과를 비교한 결과, 주요 동적접촉력 특성인 평균접촉력 및 접촉력 표준편차가 비교적 잘 일치하는 것을 확인하였다. 또한 해석모델을 이용하여 전차선 장력과 접촉력과의 상관관계를 차량 운행속도에 따라 제시하였으며, 이를 이용하여 각 운영속도별 최적 전차선 장력을 제시하였고 이를 국제규격과 비교하였다. 그 결과 해석을 통해 도출된 결과와 국제 규격에서 권장하는 전차선 장력이 비교적 잘 일치하는 것을 알 수 있었다.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권1호
• /
• pp.51-56
• /
• 2013

With the active development of hybrid electric vehicle (HEV), the application of interior permanent magnet synchronous motor (IPMSM) has been expanded. As wide driving region of IPMSM for electric vehicle (EV) traction motor is required, many studies are conducted to improve characteristics of a motor in both low and high-speed driving regions. A motor in high-speed driving region generates (produces) large stress to the rotor. Thus, the rotor needs to be designed considering the mechanical safety. Therefore, in this paper, we conducted stress analysis and electromagnetic analysis to determine the centerpost's distance which is considered important during the design of IPMSM for EV traction motor in order to secure mechanical safety and satisfy specifications of output requirement.