• Journal of Ocean Engineering and Technology
• /
• v.31 no.5
• /
• pp.335-339
• /
• 2017

This study investigated the sea trial performance of a wave piercing high speed planing hull (WPH). The bow shape of the boat is sharp, and it has no chine or spray strip like a normal planing boat. The skeg is attached to the bottom of the boat in the longitudinal direction from the bow to the stern. The speed performance was analyzed as the speed dropped in a wave, and the seakeeping performance was compared with that of a planing boat with a similar velocity coefficient by measuring the vertical acceleration of the bow in the wave. The turning circle was compared with Lewandowski's estimation for a planing boat. As a result of this study, it was confirmed that the velocity drop of the developed WPH was not large in a wave, and the vertical acceleration was greatly reduced compared with that of a normal planing boat. The turning circle was somewhat larger than the estimated results for a planing boat, but the overall tendency was the same.

• 한국기계연구소 소보
• /
• s.10
• /
• pp.63-77
• /
• 1983

This paper presents the hydrodynamic performance characteristics of a planing boat which was tested with a new dynamometer system specifically designed to measure towing force along the thrust plane, the change in trim angle and the vertical displacement of the model center of gravity from still water condition. The test conditions include systematic variations in the three positions of LCG and the three load coefficients of a high speed planing boat.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.4
• /
• pp.867-875
• /
• 2014

Planing crafts were specifically designed to achieve relatively high speeds on the water. When a planing craft is running at high speed, dynamic pressure on the bottom makes the boat rise on the surface of the water. This reduces the area of the sinking surface of the boat to increase air resistance. Air resistance means the resistance that occurs when the hull and deck house over the surface of the water come in contact with the air current. In this paper, we carried out a CFD numerical analysis to find optimal deck houses that decreased air-resistance on the water when planing crafts are running at high speed. We finally developed the deck house shape of high-speed planing crafts that optimally decreased air resistance.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.7 no.2
• /
• pp.19-26
• /
• 1970

Three kinds of high speed boat have been tested in the Seoul National University tank. Under the range of speed length ratio 2.5, displacement hulls have shown less resistance value than planing hull, but over the range of 3.0, planing hulls are better. Change of resistance due to the change of displacement is more severe in planing hull.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.585-598
• /
• 2021

The course-keeping stability of a high speed planing boat should be considered at the design stage for its safe operations. The shape of waterjet intake plane is one of important design parameters of a waterjet propelled planing boat. That has significant influences on the stern flow patterns and pressure distributions. In this study, the effects of the waterjet intake shapes of planing boats on the course-keeping stabilities are investigated. Two kinds of designed planing boats have the same dimensions, but there are differences in waterjet intake plane shapes. Captive and free-running model tests, Computational Fluid Dynamics (CFD) analyses are carried out in order to estimate their hydrodynamic performances including course-keeping stabilities. The results show that the flat and wide waterjet intake plane of the initially designed boat makes the course-keeping stability worse. The waterjet intake shape is redesigned to improve the course-keeping stability. The improved performances are confirmed by free-running model tests and full-scale trials.

• Journal of Navigation and Port Research
• /
• v.34 no.8
• /
• pp.623-628
• /
• 2010

High speed marine vehicle, such as semi-planing, planing craft have been developed recently. These ships paid attention to the resistance characteristics, especially in high speed region. Model test method is divided to two equipment greatly, first 'Towing tank', second 'C.W.C.'. It is difficult to estimate a resistance characteristics for high speed boat. because these are made for low speed ship. This paper suggests a new model test method and system. This is real sea model test and it's comprised of eight part. Firstly, This method is tested at C.W.C that is possible to using in real sea model tes using low speed boat modelt. And then, Real sea model test and CFD calculation are performed and compared with tow way used high speed boat model. It can be a good way to estimate a performance for high speed boat.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.2
• /
• pp.69-74
• /
• 2016

A new wave-piercing-type high-speed planing boat without a chine was developed, and its basic performance was investigated in a model test, including the resistance, trim, and sinkage. The maximum speed of the developed ship was 35 knots. The hull form was developed by combining a VSV (very slender vessel) and TH (transonic hull), which have large deadrise angles at the bow. The main dimensions were estimated by a statistical approach using actual ship data. The effect of a side fin attached at the stern near the water line was investigated from a resistance point of view. It was found that the developed hull form showed the possibility of a new concept for a high-speed planing hull without a chine, and the side fin played an important role in increasing the resistance performance by controlling the trim and sinkage in the high-speed range.

• 한국기계연구소 소보
• /
• s.13
• /
• pp.87-98
• /
• 1984

An experimental study carried out to predict the performance characteristics of a high speed planing boat at the two displacements whose hull form shows hard chines form transom to bow. In the resistance test the planing hull model was porpoising at and above 30 knots for both displacements of 30 tons and 24 tons. A small stern wedge was newly designed and attached across hull bottom. The planing hull model with the stern sedge did not show any porpoising up to the speed of 45 knots for both displacements and it analysed results shows the improvement of resistance performance and planing performance comparing with those of original hull form; i.e. for displacement of 30 tons the effective power and trim angle were reduced by 18.9% and 5.71 degrees at the speed of 28 knots, and for the displacement of 24 tons the effective power and trim angle were reduced by 23.63% and 4.37 degrees at the speed of 28 knots, respectively.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.4
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.1
• /
• pp.68-74
• /
• 2008

This study is concerned with the development of the basic planing hull form of small fishing boat in 25 knots high speed. A series of model test to determine the optimum performance hull form of actual fishing boat with 10 gross tonnage was carried out for 5 models made available planing hull form in the circulation water channel. Model test was performed with the resistance test to study the hydrodynamic characteristics of model ships and the sinkage and trim measurement to investigate the stability of model ships and also the wave pattern observation to analyze the effectiveness of model ships. As the result, the planing hull form of P-4 with deep V type bow can be derived as the best hull form with good performance especially in ship's resistance efficiency showing less residual resistance and sinkage and trim and the spray effect, etc..