• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1475-1480
• /
• 2004

Plasma Enhanced Chemical Vapor Deposition (PECVD) process uses unique property of plasma to modify surfaces and to achieve the high deposition rates. In this study, a vertical thermal RF-PECVD (Radio Frequency-PECVD) reactor is modeled to investigate thermal flow and the deposition rates with various shapes of the showerhead. The showerhead in the CVD reactor has the shape of a ring and gases are injected in parallel with the susceptor, which is a rotating disk. In order to achieve the high deposition rates, we have simulated the thermal flow fields in the reactor with several showerhead models. Especially the effects of the number of injection holes and the rotating speed of the susceptor are studied. Using a commercial code, CFDACE, which uses FVM (Finite Volume Method) and SIMPLE algorithm, governing equations have been solved for the pressure, mass-flow rates and temperature distributions in the CVD reactor. With the help of the Nusselt number and Sherwood number, the heat and mass transfers on the susceptor are investigated. In order to characteristics of measure the flatness of the layer, furthermore, the relative growth rate (RGR) is considered.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2002년도 춘계학술대회논문집
• /
• pp.13-22
• /
• 2002

This paper presents characteristics of CrOx thin-film Strain gauge pressure sensors, which were deposited on SUS630 diaphragm by DC reactive magnetron sputtering in an argon-Oxide atmosphere(Ar-(10%)$O_2$). The optimized condition of CrOx thin-film strain gauges were thicknessrange of 2500$\AA$ and annealing condition ($350^{\circ}C$, 3 hr) in Ar-10 %$O_2$deposition atmosphere. Under optimum conditions, the CrOx thin-films for strain gauge is obtained a high resistivity, $\rho$=156.7$\mu$$\Omega$cm, a low temperature coefficiect of resistance, TCR=-86 ppm/$^{\circ}C$ and a high temporal stability with a good longitudinal, 15. The output sensitivity of pressure sensor obtained is 2.46㎷/V and the maximum non-linearity is 0.3%FS and hysteresis is less than 0.2%FS. The output characteristics of pressure transmitter obtained is 4~20㎃ and total accuracy is less than $\pm$0.5%FS. In those conclusions, CrOx thin film pressure sensors is quite satisfactory for many applications in industrial electronics.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.72.1-72.1
• /
• 2010

Thin film a-Si solar cells deposited by PECVD have many advantages compared to the traditional crystalline Si solar cells. They do not require expensive Si wafer, the process temperature is relatively low, possibility of scaling up for mass production, etc. In order to produce thin film solar cells, understanding the relationship between the material characteristics and deposition conditions is important. It has been reported by many groups that the band gap of the a-Si material and the deposition rate has an linear relationship, when RF power is used to control both. However, when the process pressure is changed in order to control the deposition rate and the band gap, a diversion from the well known linear relationship occurs. Here, we explain this diversion by the deposition condition crossing different plasma regions in the Paschen curve with a simple model. This model will become a guide to which condition a-Si thin films must be fabricated in order to get a high quality film.

• 한국세라믹학회지
• /
• 제32권4호
• /
• pp.419-428
• /
• 1995

Polycrystalline silicon carbide (SiC) thick films were depostied by low pressure chemical vapor deposition (LPCVD) using CH3SiCl3 (MTS) and H2 gaseous mixture onto isotropic graphite substrate. Effects of deposition variables on the SiC film were investigated. Deposition rate had been found to be surface-reaction controlled below reactor temperature of 120$0^{\circ}C$ and mass-transport controlled over 125$0^{\circ}C$. Apparent activation energy value decreased below 120$0^{\circ}C$ and deposition rate decreased above 125$0^{\circ}C$ by depletion effect of the reactant gas in the direction of flow in a horizontal hot wall reactor. Microstructure of the as-deposited SiC films was strongly influenced by deposition temperature and position. Microstructural change occurred greater in the mass transport controlled region than surface reaction controlled region. The as-deposited SiC layers in this experiment showed stoichiometric composition and there were no polytype except for $\beta$-SiC. The preferred orientation plane of the polycrystalline SiC layers was (220) plane at a high reactant gas concentration in the mass transfer controlled region. As depletion effect of reactant concentration was increased, SiC films preferentially grow as (111) plane.

• 한국세라믹학회지
• /
• 제43권12호
• /
• pp.852-858
• /
• 2006

It is well known that $BaMgAl_{10}O_{17}:Eu^{2+}$ (BAM) and $CaMgSi_2O_6:Eu^{2+}$ (CMS) are a highly efficient blue phosphor. However, these phosphors in the form of thin films have not yet been realized clue to technical difficulties. We prepared thin film type BAM and CMS phosphors on quartz glass substrate using a pulsed laser deposition technique. The luminescent and structural properties of thin film phosphors were monitored as a function of key processing parameters such as oxygen partial pressure inside the deposition chamber, deposition time, laser energy density and the type of post-deposition treatments used. Even though we could not obtain single homogenous phases, thin films with large homogenous areas and a high photoluminescence could be produced by optimizing these processing parameters.

• 센서학회지
• /
• 제11권6호
• /
• pp.371-377
• /
• 2002

$Y_2O_3:Eu^{3+}$ and Li-doped $Y_2O_3:Eu^{3+}$ thin films have been grown on sapphire substrates using a pulsed laser deposition technique. The thin film phosphors were deposited at a substrate temperature of $600^{\circ}C$ under the oxygen pressure of 100, 200 and 300 mTorr. The films grown under different deposition conditions have been characterized using microstructural and luminescent measurements. The crystallinity and photoluminescence (PL) of the films are highly dependent on the oxygen pressure. The PL brightness data obtained from $Y_2O_3:Eu^{3+}$ films grown under optimized conditions have indicated that sapphire is one of the most promising substrate for the growth of high quality $Y_2O_3:Eu^{3+}$ thin film red phosphor. In particular, the incorporation of $Li^{+}$ ions into $Y_2O_3$ lattice could induce a remarkable increase of PL. The highest emission intensity was observed with LiF-doped $Y_{1.84}Li_{0.08}Eu_{0.08}O_3(Y_2O_3LiEu)$, whose brightness was increased by a factor of 2.7 in comparison with that of $Y_2O_3:Eu^{3+}$ films. This phosphor may promise for application to the flat panel displays.

• 한국전기전자재료학회논문지
• /
• 제21권10호
• /
• pp.923-929
• /
• 2008

On the piezoelectric polymer, PVDF (poly vinylidene fluoride), the transparent conducting oxide (TCO) electrode material thin film was deposited by roll to roll sputtering process mentioned as a mass product-friendly process for display application. The deposition method for ITO Indium Tin Oxides) as our TCO was DC magnetron sputtering optimized for polymer substrate with the low process temperature. As a result, a high transparent and good conductive ITO/PVDF film was prepared. During the process, especially, the gas mixture ratio of Ar and Oxygen was concluded as an important factor for determining the film's physical properties. There were the optimum ranges for process conditions of mixture gas ratio for ITO/PVDF From these results, the doping mechanism between the oxygen atom and the metal element, Indium or Tin was highly influenced by oxygen partial pressure condition during the deposition process at ambient temperature, which gives the conductivity to oxide electrode, as generally accepted. With our studies, the process windows of TCO for display and other application can be expected.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.253-253
• /
• 2011

ZnTe semiconductor is very attractive a material for optoelectronic devices in the visible green spectral region because of it has direct bandgap of 2.26 eV. The prototypes of ZnTe light emitting diodes (LEDs) have been reported [1], showing that their green emission peak closely matches the most sensitive region of the human eye. The optoelectronic properties of ZnTe:O film allow to expect a large optical gain in the intermediate emission band, which emission band lies about 0.4-0.6 eV below the conduction band of ZnTe [2]. So, the ZnTe system is useful for the production of high-efficiency multi-junction solar cells [2,3]. In this work, the ZnTe:O thin films were deposited on Al2O3 substrates by using the radio frequency magnetron sputtering system. Three sets of samples were prepared using argon and oxygen as the sputtering gas. The deposition chamber was pre-pumped down to a base pressure of 10-7 Torr before introducing gas. The deposition pressure was fixed at 10-3 Torr throughout this work. During the ZnTe deposition, the substrate temperature was 300 oC. The optical properties were also investigated by using the ultraviolte-visible (UV-Vis) spectrophotometer.

• 대한금속재료학회지
• /
• 제49권12호
• /
• pp.945-949
• /
• 2011

The cycling characteristics of $MgH_2$ made by hydriding chemical vapor deposition method have been investigated. The particle size of $MgH_2$ made by HCVD was about $1{\mu}m$. The cycling experiment was performed by measuring hydrogen quantity absorbed at 673 K and under 35 atm of hydrogen pressure for 30 min. Up to 3 cycles the hydrogen storage capacity increased, but from 4 to 6 cycles the hydrogen storage capacity decreased rapidly. During this cycling test the particle size increased gradually from $1{\mu}m$ to $6{\mu}m$. This increase was due to sintering by the high reaction temperature and the heat of reaction during hydrogen absorption. From 7 to 30 cycles, the hydrogen storage capacity was maintained at 5.8 wt%. Even after 30 cycles, the plateau pressure was constant.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -2
• /
• pp.1042-1045
• /
• 2002

The scaling of device dimension and supply voltage with high performance and reliability has been the main subject in the evolution of VLSI technology, The MOSFET structures become susceptible to high field related reliability problems such as hot-electron induced device degradation and dielectric breakdown. HLDBD(HLD Buffered Deposition) is used to decrease junction electric field in this paper. Also we compared the hot carrier characteristics of HLDBD and conventional.