• 한국정밀공학회지
• /
• 제16권1호통권94호
• /
• pp.219-225
• /
• 1999

Monitoring of the cutting force signals in cutting process has been well emphasized in machine tool communities. Although the cutting force can be directly measured by a tool dynamometer, this method is not always feasible because of high cost and limitations in setup. In this paper an indirect cutting force monitoring system is developed so that the cutting force in turning process is estimated based on a AC spindle drive model. This monitoring system considers the cutting force as a disturbance input to the spindle drive and estimates the cutting force based on the inverse dynamic model. The inverse dynamic model represents the dynamic relation between the cutting force, the motor torque and the motor power. The proposed monitoring system is realized on a CNC lathe and its estimation performance is evaluated experimentally.

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.151-158
• /
• 2005

Micro-machine tool is essential in the micro/meso cutting for the sake of saving of space, resources, and energy. In this research, a micro-turning lathe was fabricated with piezoelectric feed drive mechanism, and motion of each axis was generated by stepwise mechanism with two piezo actuators. The resolution to drive the axis was $0.05{\mu}m$ and position accuracy less than $2{\mu}m$ was assured. From the positioning experiment, piezo feed mechanism is good enough for the micro machine tools. Many fuming experiments were carried out with diamond-cutting tools to evaluate cutting capability of a machine tool. Continuous flow type chip could be obtained even if the cutting speed was very low due to small diameter of workpiece. However, thorough investigation about machineability in micro/meso cutting is inevitable to assure high quality surface roughness in micro machine tool.

• 한국기계가공학회지
• /
• 제16권4호
• /
• pp.62-68
• /
• 2017

Since the aircraft parts industry is a high-value-added industry, mass production order production, and the hundreds of thousands. Therefore, parts produced However, since these parts require high reliability and stability, a high degree of precision is required. In Korea, there on the roughness of the machined surface in cutting process. However, research on the surface roughness characteristic obtained by which is widely used for aircraft parts is still insufficient in Korea. The purpose of this study is to investigate the effect of turning tool rotation speed and X axis feed rate on the surface roughness of cutting tools in CNC lathes during cutting of aluminum alloy 7075.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.985-990
• /
• 1995

Recently, the development of high speed and high precision NC-lathe for piston head machining is needed for the complexity and diversity of the piston head shape used in automobile reciprocating engine. THe piston head has many complex shapes in the aspect of fuel economy, such as ovality, profile, double ovality and recess. Among them, for the maching of the over shape of 0.1~1mm the cutting tool should move periodically symchronized with the rotation of piston workpiece. The cutting tool feeed system must have high positioning accuracy for the precise machining, high speed for the fast maching and high dynamic stiffness for the cutting force. The linear brushless DC motor is used for satisfying these coditions. The ballbush guide and supporting guide using turcite is used for the guidance of the feed drive system. Linear encoder, digital servo ampllifer and controller are used for driving the motor. THis paper presents the design and simulation of the new tool feed system for noncircular machining.

• 한국기계가공학회지
• /
• 제11권3호
• /
• pp.110-115
• /
• 2012

For domestic aircraft industry, not mass production of components is limited, small production scale of the order is made by part because many kinds of hundreds of thousands of kinds of small quantity batch production system are taking. But the high reliability and stability are required during the processing because they require high precision parts are required. It is found that when C-axis rotation speed was increased, the diameter of the cutting tool decreased with increasing surface roughness, while the turn-mail feed rate was increased with increasing the surface roughness.

• 한국정밀공학회지
• /
• 제31권7호
• /
• pp.635-642
• /
• 2014

The large volume multi-tasking vertical lathe was developed for machining the bearing parts for a wind power generator. Although the machined part is large in size high precision tolerances are required recently. One of the most important components to achieve this mission is the rotating table which holds and supports the part to be machined. The oil hydrostatic bearing is adopted for the thrust bearing and the rolling bearing for the radial bearing. In this article experimental performance evaluation and its analysis results are presented. The rotational accuracy of the table is assessed and the frequency domain analysis for the structural loop is performed. And in order to evaluate the structural characteristic of table the moment load experiment is performed. The rotational error motion is measured as below 10 ${\mu}m$ for the radial and axial direction and 22,800 Nm/arcsec of moment stiffness is achieved for the rotary table.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1991년도 춘계학술대회 논문집
• /
• pp.150-157
• /
• 1991

As the system monitoring technology become required in order to imporve the system performance and the productivity, We've studied to the detection for the tool breakage using AE sensor that is able to detection of generated high frequency strss pulse at cutting. The method of spectrum analysis are used for analysis of AE signals in detection system. The experiments are carred out in a CNC lathe.

• 한국기계가공학회지
• /
• 제17권1호
• /
• pp.63-68
• /
• 2018

At present, ultra-precision cutting technology has been studied in Korean research institutes, focusing on development of ultra-precision cutting tool technology and ultra-precision control engineering. However, the developed technologies are still far behind advanced countries. It focuses on metals including aluminum, copper and nickel, and nonmetals including plastics, silicone and germanium which require high precision while using a lathe. It is hard to implement high precision by grinding the aforementioned materials. To address the issue, the ultra-precision cutting technology has been developing by using ultra-precision machine tools very accurate and strong, and diamond tools highly abrasion-resistant. To address this issue, this study aims to conduct ultra-precision cutting by using ECTS (Error Compensation Tool Servo) to improve motion precision of elements and components, and compensate for motion errors in real time. An IR camera is used for analyzing cutting accuracy differences depending on the heat generated in diamond tools in cutting to examine the heat generated in cutting to study cutting accuracy depending on generated heat.

• 한국생산제조학회지
• /
• 제7권6호
• /
• pp.132-140
• /
• 1998

Recently, precision machining technology has been developed continuously in order to make high productivity and quality assurance of the precision parts of several industrial fields. Waviness may occur on the surface of the machined parts due to the table motion error and the dynamic cutting mechanism between the tool and the workpiece. The waviness may fall off the form accuracy of the precision machine parts. In the research, a micro cutting device with piezoelectric actuator has been developed to control precise depth of cut and compensate the waviness on the surface of the workpiece. Experiments have been carried out in the precision lathe. The characteristics of the surface profile and cause of the waviness profile have been analyzed and waviness profiles of some cause have been compared with those of experiments.

• 한국정밀공학회지
• /
• 제23권10호
• /
• pp.44-51
• /
• 2006

According to global trend of the expanding need of high-quality automobiles, the usage of small precise worm consisting of gearing part for motors to actuate convenience modules has increased rapidly. Precision of those worms has very sensitive characteristic to motor performance and noise. Forming process has been generally used to manufacture worms because of its mass productivity. However, it has problems such as deformation due to residual stress and wear of dies. Planetary milling and side milling are among alternatives using cutting tools. To overcome those problems the two machining methods have some contrast features in the sense of tool numbers and cutting mechanism. In this paper, machinability of both methods was compared in terms of cutting force, precision and cycle time.