• Journal of Biomedical Engineering Research
• /
• v.6 no.1
• /
• pp.19-30
• /
• 1985

This paper describes the EMG signals in frequency domain using power spectral density, The changes in the moan frequency can represent the energy distribution which results from changing in load before and during fatigue. Most of EMG signal power spectrum is located between 10 and 200Hz. Shifts of the high-energy regions of the power spectra can be inferred from the changes in the mean frequency. If the load is increased without fatigue-ocurring, the high frequency regions have more energy than the low frequency regions. And if load is increased during fatigue, the low frequency regions have more energy than the high frequency regions.

• Korean Journal of Materials Research
• /
• v.31 no.5
• /
• pp.272-277
• /
• 2021

Owing to its low cost, easy fabrication process, and good ionic properties, aqueous supercapacitors are under strong consideration as next-generation energy storage devices. However, the limitation of the current collector is its poor electrochemical stability, leading to low energy storage performance. Therefore, a reasonable design of the current collector and the acidic electrolyte is a necessary, as well as interfacial engineering to enhance the electrochemical performance. In the present study, graphite foil, with excellent electrochemical stability and good electrical properties, is suggested as a current collector of aqueous supercapacitors. This strategy results in excellent electrochemical performance, including a high specific capacitance of 215 F g^-1 at a current density of 0.1 A g^-1, a superior high-rate performance (104 F g^-1 at a current density of 20.0 A g^-1), and a remarkable cycling stability of 98 % at a current density of 10.0 A g^-1 after 9,000 cycles. The superior energy storage performance is mainly ascribed to the improved ionic diffusion ability during cycling.

• Nuclear Engineering and Technology
• /
• v.31 no.2
• /
• pp.139-150
• /
• 1999

The swelling pressure of a potential buffer material was measured and the effect of dry density, bentonite content and initial water content on the swelling pressure was investigated to provide the information for the selection of buffer material in a high-level waste repository. Swelling tests were carried out according to Box-Behnken's experimental design. Measured swelling pressures were in the wide range of 0.7 Kg/$\textrm{cm}^2$ to 190.2 Kg/$\textrm{cm}^2$ under given experimental conditions. Based upon the experimental data, a 3-factor polynomial swelling model was suggested to analyze the effect of dry density, bentonite content and initial water content on the swelling pressure The swelling pressure increased with an increase in the dry density and bentonite content, while it decreased with increasing the initial water content and, beyond about 12 wt.% of the initial water content, levelled off to nearly constant value.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1083-1088
• /
• 2001

To predict vibrational energy density and intensity of complex structures in medium-to-high frequency ranges, Power Flow Finite Element Method(PFFEM) programs for the plate, beam and some coupled structural elements are developed at present. The vibration energy density and intensity of foreign vehicle is predicted successfully with FE full model of 60,000 DOF using the developed PFFEM program.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.5 no.3
• /
• pp.392-403
• /
• 2013

For the analysis of radiating noise problems in medium-to-high frequency ranges, the Energy Flow Boundary Element Method (EFBEM) was developed. EFBEM is the analysis technique that applies the Boundary Element Method (BEM) to Energy Flow Analysis (EFA). The fundamental solutions representing spherical wave property for radiating noise problems in open field and considering the free surface effect in underwater are developed. Also the directivity factor is developed to express wave's directivity patterns in medium-to-high frequency ranges. Indirect EFBEM by using fundamental solutions and fictitious source was applied to open field and underwater noise problems successfully. Through numerical applications, the acoustic energy density distributions due to vibration of a simple plate model and a sphere model were compared with those of commercial code, and the comparison showed good agreement in the level and pattern of the energy density distributions.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.314-317
• /
• 2004

On 9/5/2003, the planet probe “HAYABUSA” as MUSES-C project was launched by The Institute of Space and Astronautical Science. “HAYABUSA” has microwave discharge ion engines and these engines are characterized by their high efficiency and specific impulse in comparison with chemical engine. A large ion engine can be used as a planet explorer, while a small ion engine can be used as attitude control of small satellite. We have been developing a high thrust density microwave discharge ion engine using “Multi-Monopole Antenna”. The performance of this engine are: ion cost of 344W/A, propellant utilization efficiency of 52% and thrust density of 0.055mN/$\textrm{cm}^2$ for Kr gas flow rate of 2.5sccm, microwave(2.45㎓) power of 32W and acceleration voltage of l.4㎸.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.10
• /
• pp.1233-1235
• /
• 2016

It is desirable to place virtual machines for minimizing the number of operational servers in order to save energy in high-density cloud computing environment. However, the compacted servers can incur heat islands. This paper firstly finds out the relationship between the server utilization by the virtual machine placement and the energy consumption of servers and heat from servers. Then, this paper proposes a virtual machine placement algorithm to save energy consumed and avoid heat islands.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.4
• /
• pp.817-820
• /
• 2009

To meet the high current load requirement from the high energy density realized by metal oxide and high power density graphite, we propose a novel hybrid supercapacitor consisting of Nb2O5 and KS6 graphite in 1.0 M LiPF6-EC:DEC (1:2). This new system exhibits a sloping voltage profile from 2.7 to 3.5 V during charging and presents a high operating voltage plateau between 1.5 and 3.5 V during discharging. The cell was tested at a current density of 100 mA/g with a cut-off voltage between 3.0 and 1.0 V. This novel energy storage system delivers the highest initial discharge capacity of 55 mAh/g and exhibits a good cycle performance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.1
• /
• pp.60-65
• /
• 2000

The structural and electrical characteristics of PLZT thin films fabricated onto Pt/Ti/SiO\ulcorner/Si substrates by a pulsed laser deposition were investigated to develop the high dielectric thin films were fabricated with different energy density by pulsed laser deposition. This PLZT thin films of 5000 thickness were crystallized at 600 $^{\circ}C$, 200 mTorr O\ulcorner pressure for 2 J/$\textrm{cm}^2$ laser energy density, the arain structure was transformed from planar to columnar grain. It was clearly noted from the SEM observations that oxygen pressured laser powers affect microstructures of the PLZT thin films. 14/50/50 PLZT this film showed a maximum dielectric constant value of $\varepsilon$\ulcorner=1289.9. P-E hysteresis loop of 14/50/50 PLZT thin film was flim ferro-electric. Leakage current density of 14/50/50 PLZT thin film was 10\ulcorner A/$\textrm{cm}^2$.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.702-704
• /
• 2011

For the representative of the poor performance of liquid fuel(Jet A-1), the physical properties effests of different additive ratios in the liquid fuel have been investigated. The mixed liquid fuel could be analyzed by principal factor of liquid fuel such as, density, viscosity and caloric value. This additives will be usefully applied to high energy density liquid fuel development.