• 한국해양공학회지
• /
• 제31권5호
• /
• pp.335-339
• /
• 2017

This study investigated the sea trial performance of a wave piercing high speed planing hull (WPH). The bow shape of the boat is sharp, and it has no chine or spray strip like a normal planing boat. The skeg is attached to the bottom of the boat in the longitudinal direction from the bow to the stern. The speed performance was analyzed as the speed dropped in a wave, and the seakeeping performance was compared with that of a planing boat with a similar velocity coefficient by measuring the vertical acceleration of the bow in the wave. The turning circle was compared with Lewandowski's estimation for a planing boat. As a result of this study, it was confirmed that the velocity drop of the developed WPH was not large in a wave, and the vertical acceleration was greatly reduced compared with that of a normal planing boat. The turning circle was somewhat larger than the estimated results for a planing boat, but the overall tendency was the same.

• 대한조선학회논문집
• /
• 제49권2호
• /
• pp.182-188
• /
• 2012

The hull form design technique for high speed power boat based on the parametric design method is presented in this paper. While the design methods of conventional vessels that are currently in use have been well developed in various aspects from existing database. However, an easy and simple design program for high speed power boats needs to be provided for the relatively small boat builders who are in lack of experience and skilled manpower. This paper presents a parametric design technique which is aimed to provide an easier creation of a new model by inputting several parameters, such as angles and lengths, which correlate with hydrodynamics characteristic for high speed boats. The paper also introduces the prototype program developed to design power boat with parametric design technique.

• 한국해양공학회지
• /
• 제22권4호
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• 한국항해항만학회지
• /
• 제34권8호
• /
• pp.623-628
• /
• 2010

현재 모형선을 이용한 선형성능 검증설비는 예인수조와 회류수조 두설비가 주로 이용된다. 이들 설비는 주로 저속 대형선박을 위해 기법들로 소형 고속어선 및 고속레저선박의 저항성능 평가를 수행하기에 전차의 속도와 유속이 목표속도에 미치지 못해 어려움이 존재한다. 따라서 고속 선박의 저항성능 평가를 위해 새로운 기법 정립 연구가 필요하다. 이에 고속선의 저항성능 시험을 위해 실제 해상에서 선박을 이용한 모형시험을 고안하고 측정시스템을 구성하였다. 시스템구성은 총 8개의 파트로 구성되어 있으며, 시스템 검증을 위해 C.W.C에서 저속선의 모형을 이용하여 시험을 수행하여 시스템 적용 가능성을 검증하였다. 또한 실제 해상에서 고속선 모형선을 이용하여 시험을 수행하였으며, 이 결과를 CFD해석 결과와 비교하여 실해상 모형시험 방법의 가능성을 확인 하였다.

• 한국기계연구소 소보
• /
• 통권10호
• /
• pp.63-77
• /
• 1983

This paper presents the hydrodynamic performance characteristics of a planing boat which was tested with a new dynamometer system specifically designed to measure towing force along the thrust plane, the change in trim angle and the vertical displacement of the model center of gravity from still water condition. The test conditions include systematic variations in the three positions of LCG and the three load coefficients of a high speed planing boat.

• Journal of Ship and Ocean Technology
• /
• 제9권2호
• /
• pp.1-10
• /
• 2005

A light-weight cantilever type towing carriage was devised and installed in the towing tank at Seoul National University. Wireless measurement devices were also provided for appropriate data acquisition during high-speed towing tests. With the new carriage system, a series of model tests were performed to investigate the hydrodynamic characteristics of the racing boat in the towing tank and the resistance test results had sufficient accuracy so that they could be used in the development of a high speed planning hull.

• 한국항해항만학회지
• /
• 제42권3호
• /
• pp.177-186
• /
• 2018

보트의 초기설계단계에서 설계자는 주요치수 결정을 위해 많은 정보를 필요로 하며, 그러한 정보의 대부분은 해당 보트와 유사한 실적선 자료들을 많은 시간에 걸쳐 조사 및 분석함으로써 얻을 수 있다. 또한, 결정된 주요치수는 설계과정(기본/상세설계) 전반에 걸쳐 영향을 미치게 되고, 이는 결국 보트의 안정성과 성능으로 직결된다. 따라서 본 연구에서는 700여 척의 실적선 자료를 이용하여 보트 초기설계시스템(설계지원플랫폼)을 개발하고, 50피트급 고속보트를 대상으로 이를 활용하여 설계자가 초기설계단계에서도 주요치수를 편리하고 합리적으로 도출 및 결정할 수 있음을 확인하였다.

• 한국해양공학회지
• /
• 제30권2호
• /
• pp.69-74
• /
• 2016

A new wave-piercing-type high-speed planing boat without a chine was developed, and its basic performance was investigated in a model test, including the resistance, trim, and sinkage. The maximum speed of the developed ship was 35 knots. The hull form was developed by combining a VSV (very slender vessel) and TH (transonic hull), which have large deadrise angles at the bow. The main dimensions were estimated by a statistical approach using actual ship data. The effect of a side fin attached at the stern near the water line was investigated from a resistance point of view. It was found that the developed hull form showed the possibility of a new concept for a high-speed planing hull without a chine, and the side fin played an important role in increasing the resistance performance by controlling the trim and sinkage in the high-speed range.

• 해양환경안전학회지
• /
• 제21권6호
• /
• pp.784-789
• /
• 2015

본 연구는 소형 고속정의 운항한계를 검토하기 위하여 수행되었다. 일반적으로 내항성능의 검토는 선형의 결정 단계 전에 이루어지지만 본 연구는 선박의 건조가 완료된 후에 이루어졌다. 검토 결과, 종동요, 수직 및 수평가속도, 슬래밍의 운동성능은 특정한 조우각을 제외하고는 만족하였으나 갑판침수의 경우에는 해석을 수행한 모든 조건에서 만족하지 않았다. 이것은 대상선박의 크기가 소형이기 때문에 선박의 속도나 파도와의 조우각보다는 해상상태가 설정한 내항성능 기준의 만족 여부에 더 큰 영향을 미쳤기 때문으로 보인다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.213-215
• /
• 2004

Water jet propulsion system has high efficiency on middle to high speed, and it provides better safety than conventional screw propeller because it has not projected propeller and rudder. So many leisure boat and high-speed ferries use this propulsion system. We developed water-jet propulsion unit for small planning boat, and launched that in the boat, after that we tested water-jet unit in the lake. As a result, we certify heat dissipation at the bearing housing and reverse duct's shape for neutral position are important at the design, and alignment water-jet unit and keel line are important at the launching, and ship's resistance performance and jet's propulsion performance also are needed to consideration.