• Proceedings of the KSR Conference
• /
• 2003.10a
• /
• pp.181-186
• /
• 2003

In order to develop a high speed train, various conditions have been considered. Fatigue strength assessment by the fluctuation of pressure is an important one. In this study, a numerical simulation has been performed to estimate the fluctuation and frequency of pressure when KHST(Korean High Speed Train)passes through tunnels in the Kyung-Bu high-speed railway. The simulation was based on KHST running the Kyung-Bu high-speed line with the speed of 350km/h and the interval of 10 minute headway. And the tunnel entrance speed was estimated by TPS program. Therefore, the fluctuation and frequency of pressure is expressed in Weibull distribution function in the above running situation. The result in this study would be good guidance to calculate the fatigue life and the index of reliability of body structure. We are going to conduct more study to measure the real value of the pressure of the carbody passing through tunnels, to assess the fatigue reliability and to develop method ＆ procedure for the fatigue reliability design.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.3
• /
• pp.59-64
• /
• 2008

Spindle units of machine tool are very important part in the manufacturing area. Recently high speed machining has become the main issue of metal cutting. To develop high speed machine tools, a lot of studies have been carried out for high speed spindle. Due to increase of the rotational speed of the spindle, there has been renewal of interest in tooling system of high speed spindle. This paper concerns the static stiffness in the main spindle interface according to variation of clamping force, rotational speed and tool holder shank. Finite element analysis is performed by using a commercial code ANSYS workbench. From the results, it has been shown that the geometry of tool holder shank is mostly influence on the variation of the static stiffness in the main spindle interface.

• International Journal of Railway
• /
• v.6 no.2
• /
• pp.78-84
• /
• 2013

This paper is about the first experiment in Korea that was conducted on speeding increase up with rail speeds at 430km/h at high speed railway of designed 350km/h. and analysis data collected on vibration accelerations of roadbed. There are barely references on roadbed behavior measurement with rail speeds more than 350 km/h in Korea as it has never been conducted the experiment on it. So the experiments were confirmed the reliability through crosschecking the figures/values from respective sensors and measuring devices after measuring EMS and ICP types. Based on the study, values of vibration acceleration were less than 12% compared with the ones that conducted while speeding up of HEMU-430X. Also, figures of HSB for concrete bed tracks were 52% against the standard. According to the results, all the performance evaluation of vibration acceleration for roadbeds in transition zones is under the standard.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1195-1200
• /
• 2008

The railway bridge design specification used in our country at present, is reflected results that take into account link between vehicle and roadbed according to decision of TGV vehicle style in 1994, and executes design verification. Hereafter, the particular loading condition and the design speed of the high-speed EMU that is recognized to the next generation of high speed railway, are plain difference with TGV vehicle style decided in 1994. The effect that these load and design speed get in roadbed, especially superstructure, displays difference with the existent high speed railway. The goal of this study is to choose the suitable bridge type, and to reduce the construction cost for the next generation of railway, i.e., the high-speed EMU.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.2
• /
• pp.453-458
• /
• 2017

R-Bar (Overhead Rigid Conductor system) has been lately used for the speed of over 200km/h in Europe, while it has been developed and used for the max. speed of 120km/h in Korea. Because R-Bar has advantages of reduction of tunnel cross sectional area and maintenance, its development for more high-speed is urgent in Korea having many mountain area. Therefore a sensitivity analysis of design parameters for the speed-up of R-Bar has performed in this study. For the analysis, we have developed a program for the prediction of dynamic characteristics between a pantograph and R-Bar. The program was evaluated with the actual test result and a current collection performance according to the parameters such as a distance between brackets, a stiffness of bracket and of R-Bar rail was predicted with the program.

• Wind and Structures
• /
• v.32 no.5
• /
• pp.487-499
• /
• 2021

The wind-blown sand effect on the high-speed train is investigated. Unsteady RANS equation and the SST k-ω turbulent model coupled with the discrete phase model (DPM) are utilized to simulate the two-phase of air-sand. Sand impact force is calculated based on the Hertzian impact theory. The different cases, including various wind velocity, train speed, sand particle diameter, were simulated. The train's flow field characteristics and the sand impact force were analyzed. The results show that the sand environment makes the pressure increase under different wind velocity and train speed situations. Sand impact force increases with the increasing train speed and sand particle diameter under the same particle mass flow rate. The train aerodynamic force connected with sand impact force when the train running in the wind-sand environment were compared with the aerodynamic force when the train running in the pure wind environment. The results show that the head car longitudinal force increase with wind speed increasing. When the crosswind speed is larger than 35m/s, the effect of the wind- sand environment on the train increases obviously. The longitudinal force of head car increases 23% and lateral force of tail increases 12% comparing to the pure wind environment. The sand concentration in air is the most important factor which influences the sand impact force on the train.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.12
• /
• pp.1820-1823
• /
• 2013

An overhead catenary system is the one of the main subjects for increasing speed in electric railway. When a vehicle increases the speed over 350km/h, vibrations and wave propagation reflections occur severely. Therefore, the system suitable for the speed are needed. A wave propagation speed of contact wire is the main criteria to determine the tension for the system. Therefore, a train speed is restricted below 70% of wave propagation speed of it in European railway code. In this study, we measured a strain and uplift of contact wire while HEMU-430X tain is operated for the speed-up trial test in Kyungbu high-speed railway. The measured strain and uplift are analyzed with wave propagation speed according to the speed-up. The more a train speed reaches to a propagation speed, the more measured strain is high. Through the study, an experimental approach is performed about the code which a train speed is restricted below 70% of wave propagation speed of it.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.454-459
• /
• 2000

The high hardened materials that are remarkable in aspects of durability have been used for die and mold industry. As the high hardened materials are hard to machine, the high-speed machining is essential to manufacture these materials. Currently, in the general turning and milling, experiments to the tool wear monitoring have studied, but those have not applied in high-speed machining. In this study, the cutting mechanism was analysed by the cutting force according to cutting conditions, and the parameters to monitor the tool wear were selected from the tendency of the cutting force and acceleration according to cutting length in the high-speed machining of the high hardened materials(STD11).

• ETRI Journal
• /
• v.37 no.2
• /
• pp.241-250
• /
• 2015

In this paper, we present novel high-speed transmission schemes for high-speed ultra-high frequency (UHF) radio-frequency identification communication. For high-speed communication, tags communicate with a reader using a high-speed Miller (HS-Miller) encoding and multiple antennas, and a reader communicates with tags using extended pulse-interval encoding (E-PIE). E-PIE can provide up to a two-fold faster data rate than conventional pulse-interval encoding. Using HS-Miller encoding and orthogonal multiplexing techniques, tags can achieve a two- to three-fold faster data rate than Miller encoding without degrading the demodulation performance at a reader. To verify the proposed transmission scheme, the MATLAB/Simulink model for high-speed backscatter based on an HS-Miller modulated subcarrier has been designed and simulated. The simulation results show that the proposed transmission scheme can achieve more than a 3 dB higher BER performance in comparison to a Miller modulated subcarrier.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.393-398
• /
• 2001

The technique of high speed machining is widely studied in machining fields, because the high efficiency and accuracy in machining can be obtained in high speed machining. Unfortunately the development of tool for high speed machining in not close behind that of machine tool. In this study, several types flat endmill is prepared for obtaining data according to tool shape. Especially, we concentrated in helix angle, number of cutting edge, rake angle and relief angle. Machinability is measured by cutting force, tool life, tool wear, chip shape and surface roughness according to cutting length. 3-axis cutting forces are acquired from the invented tool dynamometer for high speed machining. Particularly, we found out that the axial cutting force waveform has a good relation with tool wear features. By above results, it is suggested the endmill tool with $45^{\circ}$ helix angle, 6 cutting edge, $-15^{\circ}$ rake angle and $12^{\circ}$ relief angle be suitable for high speed machining