• Journal of Biomedical Engineering Research
• /
• v.16 no.3
• /
• pp.301-308
• /
• 1995

A high-precision pre-amplifier is designed for general use in EEG measurement system. It consists of signal generator, signal amplifier with a impedance converter, shield driver, body driver, differential amplifier, and isolation amplifier. The combination of minimum use of inaccurate passive components and the appropriate matching of each monolithic amplifiers results in good noise behavior, low leakage current, high CMRR, high input impedance, and high IMRR. The performance of EEG pre-amplifier has been verified by showing the typical EEG pattevn of a nomad person through the clinical experiments.

• Tribology and Lubricants
• /
• v.27 no.1
• /
• pp.13-18
• /
• 2011

The ultra-precision products which recently experienced high in demands had included the large areas of most updated technologies, for example, the semiconductor, the computer, the aerospace, the media information, the precision machining. For early 21st century, it was expected that the ultra-precision technologies would be distributed more throughout the market and required securing more nation-wise advancements. Furthermore, there seemed to be increasing in demand of the single crystal diamond tool which was capable of the ultra-precision machining for parts requiring a high degree of complicated details which were more than just simple wrapping and policing. Moreover, the highest degree of precision is currently at 50 nm for some precision parts but not in all. The machining system and technology should be at very high performed level in order to accomplish this degree of the ultra-precision.

• Journal of Positioning, Navigation, and Timing
• /
• v.11 no.4
• /
• pp.351-360
• /
• 2022

Autonomous vehicles require precise knowledge of their position, velocity and orientation in all weather and traffic conditions in any time. And, these information is effectively used for path planning, perception, and control that are key factors for safety of vehicle driving. For this purpose, a high precision GNSS technology is widely adopted in autonomous vehicles as a core localization and navigation method. However, due to the lack of infrastructure as well as cost issue regarding GNSS correction data communication, only a few high precision GNSS technology will be available for future commercial autonomous vehicles. Recently, a high precision GNSS sensor that is based on a Broadcast-RTK system to dramatically reduce network maintenance cost by utilizing the existing broadcasting network is released. In this paper, we present the performance test result of the broadcast-RTK-based commercial high precision GNSS receiver to test the feasibility of the system for autonomous driving in Korea. Massive measurement campaigns covering of Korea region were performed, and the obtained measurements were analyzed in terms of ambiguity fixing rate, integer ambiguity loss recovery, time to retry ambiguity fixing, average correction information update rate as well as accuracy in comparison to other high precision systems.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.5
• /
• pp.17-24
• /
• 2001

Recently, the requirements for high precision and efficiency machining are gradually increased to raise international competitiveness at the industrial fields of die and molds. This trend had made effects on the industrial fields in Korea and which needs fur studying of high precision and efficiency machining. This study is to investigate the effects of the non-out of end mill in the external cylindrical machining operated by solid carbide end mills with Al-alloy in high speed machining center relating to high spindle revolution and frost fred per minute on the dimensional precision, roundness of workpiece. From the results of experimentations followings are obtained; when Al-alloy is processed by the external cylindrical cutting of end milling through the high speed revolution, if the spindle revolution is higher relating to radial depth of cut, feed per tooth in very lower situation, finally, productivity can be raised because high precision and quality products are machined high efficiently.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1066-1069
• /
• 2004

Recently the monitoring system of tool setup in high speed precision machining tool is required for manufacturing products that have highly complex and small shape, high precision and high function. It is very important to reduce time to setup tool in order to improve the machining precision and productivity and to protect the breakage of cutting tool as the shape of product is smaller and more complex. Generally, the combination of errors that geometrical clamping error of fixing tool at the spindle of machining center and the asynchronized error of driving mechanism causes that the run-out of tool reaches to 3∼20 times of the thickness of cutting chip. And also the run-out is occurred by the misalignment between axis of tool shank and axis of spindle and spindle bearing in high speed rotation. Generally, high speed machining is considered when the rotating speed is more than 8,000 rpm. At that time, the life time of tool is reduced to about 50％ and the roughness of machining surface is worse as the run-out is increased to 10 micron. The life time of tool could be increased by making monitoring of tool-setting easy, quick and precise in high speed machining center. This means the consumption of tool is much more reduced. And also it reduces the manufacturing cost and increases the productivity by reducing the tool-setup time of operator. In this study, in order to establish the concept of tool-setting monitoring the measuring method of the geometrical error of tool system is studied when the spindle is stopped. And also the measuring method of run-out, dynamic error of tool system, is studied when the spindle is rotated in 8,000 ∼ 60,000 rpm. The dynamic phenomena of tool-setup is analyzed by implementing the monitoring system of rotating tool system and the noncontact measuring system of micro displacement in high speed.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.712-717
• /
• 2000

Hydrostatic bearings have been applied to high precision machine tools and instruments, because the bearing has high stiffness, high damping and excellent straightness. This paper treats a procedure for designing a high precision press with linear hydrostatic bearings.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.107-112
• /
• 2003

The recent machine tools are requested so high-quality processing and productivity increasing. Therefore, it is so necessary to develop technology for high-speed and high-precision. This thesis touches on the development of high speed and intellectual line center. At first, the line center is necessary that strong structure, compact structure and light weight design for high-speed processing and transfer. So, it is necessary that examination of new materials and structures for light-weight and control devices for precision processing. So, it is going to make mention of the process of 1st model production for the above-mentioned based on test model production and evaluation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.619-623
• /
• 1996

This paper proposes the thermal characteristics of motor integrated spindle on high precision lathe and investigates the thermal deformation and the running error of spindle. The deformation and the running error of spindle shaft are continuously measured by the gapsensor mounted on machine. The temperature distribution is measured bythe thermal vision system and the thermocouple. The results show that the running error of spindle is dependent on the rotational speed and the thermal deformation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.567-570
• /
• 2000

Optimization of structure of a high-precision stamping press structure is performed by combination of Taguchi Method and finite element analysis. Too much difference in the stiffness between hydrostatic bearing linear guide and press structure is observed. Efforts are made to level up the stiffness of press structure to the level of hydrostatic bearing's. Some important design parameters are identified and discussed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.4
• /
• pp.721-729
• /
• 1988

Recently, the precision required by precision manufacturing and machinery related to electronics is within the domain of submicron that it is difficult to evaluate them by traditional measuring equipments and methods. Accordingly, precision of sub 0.1.mu.m super precise position-decision-apparatus and straight-guide air bearing have been researched and they are almost ready to be used. In utilizing straight-guide-table for super-precision-measurement which used externally pressurized porous air bearing as a way of externally pressurized air bearing, the high-precision-straight movement is the most crucial. In this study, the researcher conducted the experimental study with trial manufacture to see how the surrounding temperature and support condition influenced the selection and allocation of the machine composing element which is important to the high-precision-straight movement. The researcher finding showed that when the property of the rail part and support part of the semi-closed slider form is different, the heat generation of the working motor and surrounding temperature influence the high-precision-straight movement significantly and the researcher showed the influence of the condition of central load and eccentric load to the straight movement precision when the support stand of the straight-table was supported by numerical values.