• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.11
• /
• pp.1185-1191
• /
• 2008

This paper presents an approach to define an optimal piezoactuator length to actively control structural vibration. The optimal ratio of the piezoactuator length against the beam length when a pair of piezoceramic actuator and accelerometer is used to suppress unwanted vibration with direct velocity feedback(DVFB) control strategy is not clearly defined so far. It is well known that DVFB control can be very useful when a pair of sensor and actuator is collocated on structures with a high gain and excellent stability. It is considered that three different collocated Pairs of piezoelectric actuators (20, 50 and 100 mm long) and accelerometers installed on three identical clamped-clamped beams($30{\times}20{\times}1mm$). The response of each sensor-actuator pair requires strictly positive real(SPR) property to apply a high feedback gain. However the length of the piezoactuator affects the SPR property of the sensor-actuator response. Intensive simulation and experiment show the effect of the actuator length variation is strongly related with the frequency range of the SPR property. Thus an optimal length ratio was suggested to obtain relevant performance with a good stability under the DVFB strategy.

• International Journal of Internet, Broadcasting and Communication
• /
• v.16 no.1
• /
• pp.330-338
• /
• 2024

In this paper, a Ka-band high-output active phased array antenna device applicable to small radars and seekers was designed, and the improved performance was studied. The radiation device assembly consists of 1x8 arrangements, and the step flared notch antenna type. It shows low active reflection loss characteristics in broadband, and low loss characteristics by applying the air-strip feeding structure, and is designed to enable beam steering up to 45 degrees. The TRM(transmit receive module) output power is more than 2.0W per channel using GaN HPA in the transmitting path, and satisfies more than 25.0 dB gain and less than 6.0 dB noise figure in the receiving path. Accordingly, the Effective Isotropically Radiated Power(EIRP) of the antenna unit shows the performance of 0.00 dB or more and the receive gain-to-noise temperature ratio(G/T) of 0.00 dB/k or more. For demonstration, we have designed aforementioned planar array antenna which consists of 64 radiating elements having a size within 130 mm x 130 mm x 300 mm and weight of less than 4.9 kg..

• Publications of The Korean Astronomical Society
• /
• v.29 no.3
• /
• pp.53-58
• /
• 2014

We improved the antenna efficiency of the Taeduk Radio Astronomy Observatory (TRAO) 13.7-m radio telescope by adjusting the antenna panels based on digital photogrammetric measurements. First of all, we measured the surface accuracy of the main reflector of this antenna at three elevation angles of $35^{\circ}$, $45^{\circ}$, and $60^{\circ}$. We performed a total of four sets of the photogrammetric measurements and panel adjustments. When adjusting the panels, we positioned the antenna to the zenith and applied the measured data sets at the elevation of $45^{\circ}$. We found that the antenna surface accuracy has been improved by a factor of ~ 3 times after the final adjustment in comparison with the value before the adjustments. And we also found that the antenna surface accuracy tended to be slightly better at the elevation angles of $35^{\circ}$ and $60^{\circ}$ than that at the elevation angle of $45^{\circ}$. After the final panel adjustment, the aperture and beam efficiencies of the telescope have has been improved from 35% to 44%, and from 41% to 51%, respectively.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1914-1917
• /
• 2001

3D Feed Horn Shape MEMS Antenna Array는 적외선 이미지 소자 또는 Tera hertz band 등에서 많은 응용을 할 수 있는 장점을 가진 MEMS 구조체 이다. 하지만 일반적인 MEMS 공정을 이용해서 3D Feed Horn Shape MEMS antenna array를 구현하기는 적합하지 않았다. 본 논문에서는 마스크와 웨이퍼가 일체 된 형태의 경사된 척이 초 저속으로 회전하면서 노광을 할 수 있는 새로운 방식과 미러 반사구조를 이용해서 평행광을 얻을수 있는 노광장치 (MRPBI : Mirror Reflected Parallel Beam Illuminator) System제작방법을 제안하였다. 3D Feed Horn Shape MEMS Antenna의 구조적인 high apect ratio의 특성에 의해서 SU-8과 PMER Negative Photo resist를 이용한 기본적인 실험을 통해 3D 구조체의 구현 가능성을 증명하였다. 또한 Microbolometer의 성능향상을 위한 이론적인 3D MEMS Antenna Model들을 HFSS(High Frequency Structure Simulator)을 이용해서 그 최적구조를 제안하고 3D MEMS Antenna Gain 값을 비교 분석하였다.

• ETRI Journal
• /
• v.24 no.5
• /
• pp.341-348
• /
• 2002

We propose an asymmetric sampled grating laser and a multi-wavelength laser array associated with it. Asymmetric sampling periods combined with an index shifter make it possible to use first order reflection for lasing operations. With the structure of our design, we achieved a simple fabrication procedure as well as a high yield without using complex and time-consuming e-beam lithography for multi-period gratings. We analyzed the effect of mirror coating by numerical analysis to improve single mode and power extraction performance. By using high reflection-antireflection coatings, we obtained high power extraction efficiency without degradation of the single mode property. For the multi-wavelength laser array, to gain wavelength control, we varied the sampling periods from one laser to an adjacent laser across the array. With this approach, we showed the feasibility of an array of up to 30 channels with 100 GHz wavelength spacing.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.2
• /
• pp.167-173
• /
• 2009

This paper proposes an electronically beam steering array antenna, consisting of single fed active element and 4 parasitic elements, operating in 5.8 GHz ISM band. Beam steering can be achieved by controlling the reactance of the variable reactance control circuit connected to the load of the parasitic elements without using the high cost phase shifters. The proposed antenna realizes ${\pm}30^{\circ}$ beam scanning of E-plane and H-plane with the below -10 dB return loss in ISM band. The gain of the $6.18{\sim}7.53\;dBi$ in E-plane and $7.022{\sim}7.779\;dBi$ in H-plane is shown in the scanning range.

• Journal of the Korea Knowledge Information Technology Society
• /
• v.12 no.4
• /
• pp.539-550
• /
• 2017

In this paper, we designed, fabricated and tested an UHF band cylindrical dipole array antenna. In the proposed antenna, cylindrical dipoles were vertically arranged in four stages. A parallel structure feeding circuit was installed inside the cylindrical dipole and mounted so as to be broadband matching. The feeding circuit was installed at the center of the cylindrical dipole to optimize the gain flatness characteristic of the azimuth direction omnidirectional radiation pattern. Minimizing the difference between the signals branched from the feeding circuit and realizing the symmetry of the radiation pattern. The required specifications are more than 11.2% bandwidth in UHF band, above 6dBi antenna gain, standing wave ratio of 2:1 or less, less than ${\pm}1dB$ gain flatness in azimuth radiation pattern, more than 13 degrees in elevation radiation pattern of 3dB beamwidth. We confirmed the possibility of implementation through M&S and verified the result of M&S through production and testing. The test results are 11.2% bandwidth in the UHF band, 6.30 to 8.31 dBi gain, 1.53:1 standing wave ratio or less, within ${\pm}0.2dB$ gain flatness in the azimuth radiation pattern, elevation radiation pattern of 3dB beam width was 15.62 to 15.84 degrees. The test result meets all requirements specifications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.9
• /
• pp.947-956
• /
• 2008

In this paper, miniaturized conically stepped COBRA is proposed. In order to prevent electrical breakdown, COBRA, which consists of hem and lens, has to get bigger if it is designed with conventional method. Because of the phase error increase, shortening the length of the antenna without changing the aperture size leads to the reduction of the antenna gain. To avoid this, the phase error at the aperture is compensated by transforming the COBRA lens into conically stepped form. The simulations result shows that the proposed antenna has higher gain than the conventional COBRA in spite of the size reduction from 1,300 mm to 600 mm. The fabricated and measured COBRA has the gain of 26.2 dBi.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.11
• /
• pp.937-950
• /
• 2015

Microstrip reflectarray is an antenna which controls its radiation pattern with a number of reflective elements. Conventionally, the reflectarray has been researched to replace curved reflector antennas. In this paper, design theories of reflectarray is briefly introduced, and research trends of high gain and broadband reflectarrays are reviewed. To improve the gain of the reflectarrays, it is required that the reflection phase errors on the reflectarray surface be minimized. For this purpose, sufficiently wide reflection phase range and low phase sensitivity should be realized with the designed element. For bandwidth improvement, the reflection phase of the element should be linear with the frequency variation. In this paper, various researches to improve the reflection phase characteristics of the element for high gain and broadband reflectarrays, such as multi-layer and single-layer multi-resonant structures, are reviewed. Also, dual-reflectarray configuration for compact antenna design is reviewed. Finally, various applications of reflectarrays such as contoured beam, near-field focusing, and RCS reduction are reviewed.

• Journal of Advanced Navigation Technology
• /
• v.7 no.2
• /
• pp.101-107
• /
• 2003

In this study, we provide a single element log-periodic antenna that the feeding networks and array structures are aperture coupled and series dipole array type. We made the antenna for direct receiving the Moogoongwha satellite broadcasting signal. The transmission power was able to feed the patch dipole in series due to lay perpendicularly 8 series patch dipole on tapered slot. The patch dipole radiation pattern which fed in series power, make the main beam direction up $37^{\circ}{\sim}42^{\circ}$ within the BS/CS bandwidth. The main beam gain was measured 9.31~11.03 dBi. Using 32 elements to array the elements properly, we acquire $4{\times}8$ array structure on limited PCB board. As a result, it has been found that the new planar DBS antenna structure have high gain over 10dBi and acceptable elevation angle over 42 degree, and we can apply this result to commercial DBS reception antenna manufacturing.