• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.26-36
• /
• 2014

The needs of active phased arrays antenna system is getting more increased for IMT-Advanced system efficiency. The active phased array structure consists of lots of small transceivers and radiation elements to increase system efficiency. The minimized module of high efficiency transceiver is key for system implementation. The power amplifier of transmitter decides efficiency of base-station. In this paper, we design and implement minimized module of high efficiency transceiver for IMT-Advanced active phased array system. The temperature compensation circuit of transceiver reduces gain error and the analog pre-distorter of linearizer reduces implemented size. For minimal size and high efficiency, the implented power amplifier consist of GaN MMIC Doherty structure. The size of implemented module is $40mm{\times}90mm{\times}50mm$ and output power is 47.65 dBm at LTE band 7. The efficiency of power amplifier is 40.7% efficiency and ACLR compensation of linearizer is above 12dB at operating power level, 37dBm. The noise figure of transceiver is under 1.28 dB and amplitude error and phase error on 6 bit control is 0.38 dB and 2.77 degree respectively.

• Journal of Advanced Navigation Technology
• /
• v.23 no.2
• /
• pp.166-171
• /
• 2019

This paper has designed a current mode class D power amplifier to increase the transmission efficiency of a 6.78 MHz wireless power transfer (WPT) transmitter and to ensure stable characteristics even when the transmitting and receiving coil intervals change. By reducing the loss due to the parasitic capacitor component of the transistor, which limits the theoretical efficiency of the linear amplifier, this research has improved the efficiency of the power amplifier. The circuit design simulator was used to design the high efficiency amplifier, and the power output and efficiency characteristics according to the load impedance change have been simulated and verified. In the simulation, 42.1 dBm output and 95% efficiency was designed at DC bias 30 V. The power amplifier was fabricated and showed 91% efficiency at the output of 42.1 dBm (16 W). The transmitting and receiving coils were fabricated for wireless power transfer of the drone, and the maximum power added efficiency was 88% and the output power was $42.1dBm{\pm}1.7dB$ according to the load change causing from the coil intervals.

• Journal of Advanced Navigation Technology
• /
• v.12 no.3
• /
• pp.220-226
• /
• 2008

This paper proposes the Reconfigurable Doherty Amplifier(RDA) with asymmetric structure which has ${\lambda}/4$ impedance transformer for modulating the load impedance in peaking amplifier path. This structure is possible to implement a compact size for N-stage multi Doherty amplifier and to get almost same characteristics that is compared to conventional Doherty amplifier. To realize the high efficiency amplifier, we were implemented 45 Watts power amplifier at transmitter band of Wideband Code Division Multiple Access(WCDMA) base-station. As a result, in case of WCDMA 1 Frequency Allocation(FA) input signals, this amplifier has obtained a 26.3% Power Added Efficiency(PAE) at 8 dB back-off point from P1dB and an Adjacent Channel Leakage Power(ACLR) is -40.4 dBc at center frequency ${\pm}5MHz$ deviation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.15-16
• /
• 2012

General lighting will be replaced into LED due to the high efficiency, low power consumption, long life than conventional light, moreover, since it is a basically semiconductor device that can convert the electric energy to visible light at a very high speed, using these characteristics can be performed communication modulation via the high-speed ON-OFF switching. Recently, visible light communication (VLC: Visible Light Communication) technology is received attention and there have been many researches. This paper is implemented media signal transmission by combining LED with VLC, a transmitter used the LED light-emitting device and receiver used an infrared sensor. In order to increase the efficiency of the communication system to improve the existing LED visible light communication driver of power conversion efficiency and thermal issues that is applied to the visible light communication in order to improve the speed of transmission media to research a new way of LED driver.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1185-1189
• /
• 2007

In this paper, to improve the efficiency of pressurized pneumatic grit conveying for ship block open blasting process. Pressurized pneumatic grit conveying is defined as the transportation of grit(abrasive) in a compressed air flow. Total Pressure loss in flexible hose for pneumatic conveying is sum of pressure losses due to gas and grit and needle type pressure transmitter for measured pressure loss. haracteristics of grit open blasting by pneumatic conveying were studied experimentally. Studies variables were blasting nozzle ID, length and ID of flexible hose, grit flow rate, flow rate and pressure of transport air. It was experimentally proved that optimal open blasting condition and cost effective operation regarding grit blasting, obtaining a high qulity surface preparation(Sa $2^{\frac{1}{2}}$).

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.113.3-113
• /
• 2001

In this paper, we have designed the VHDL module of DS/SS QPSK wireless modem processor for digital data communication. The spread spectrum method is used for modern processor, because this method guarantees good frequency efficiency and higher security. Also, it guarantees good performance in digital communication system under multi-path interferences. The differential encoder and decoder are used for simple circuit composition in the signal detection. For the synchronization of receiver, matched filter and power detector are used. And the IF modulation/demodulation of QPSK method is used in the digital level. The transmitter of VHDL modem processor consists of differential encoder, PN code generator, and QPSK ...

• Journal of Communications and Networks
• /
• v.15 no.4
• /
• pp.338-351
• /
• 2013

Multiple-input multiple-output (MIMO) communication may provide high spectral efficiency through the deployment of a very large number of antenna elements at the base stations. The gains from massive MIMO communication come from the use of multi-user MIMO on the uplink and downlink, but with a large excess of antennas at the base station compared to the number of served users. Initial work on massive MIMO did not fully address several practical issues associated with its deployment. This paper considers the impact of channel aging on the performance of massive MIMO systems. The effects of channel variation are characterized as a function of different system parameters assuming a simple model for the channel time variations at the transmitter. Channel prediction is proposed to overcome channel aging effects. The analytical results on aging show how capacity is lost due to time variation in the channel. Numerical results in a multicell network show that massive MIMO works even with some channel variation and that channel prediction could partially overcome channel aging effects.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2004.11a
• /
• pp.383-383
• /
• 2004

• International Journal of Computer Science & Network Security
• /
• v.23 no.2
• /
• pp.140-146
• /
• 2023

With the rapid growth of new users and massive need for very high data rate in 5G communications system, different technologies have been developed and applied to enhance communication efficiency. One of those technologies is the MISO, MISO and MIMO which transmits and receives information with more reliability by using multiple antennas on transmitter or/and receiver side. This paper presents the latest trends in 5G telecommunications system based on software defined radio, A novel low-cost SIMO, MISO and MIMO using flexibility between USRP and Simulink is implemented tested and validated.

• Journal of the Korean Professional Engineers Association
• /
• v.34 no.4
• /
• pp.41-47
• /
• 2001

The paper describes SR3 (Synchronous Round Robin with Reservations), a collision-free medium access control protocol for all-optical slotted packet networks based on WDM multi-channel ring topologies where nodes are equipped with one fixed-wavelength receiver and one wavelength-tunable transmitter SR3 is derived from the SRR and MMR protocols previously proposed by the same authors for the same class of all-optical networks. SRR and MMR already achieve an efficient exploitation of the available bandwidth, while guaranteeing a throughput-fair access to each node. SR3, In addition, allows nodes to reserve slots. thereby achieving a stronger control on access delays; it is thus well suited to meet tight delay requirements, as it is the case for multimedia applications. Simulation results show that SR3 provides very good performance to guaranteed qualify traffic, but also brings signigicant performance improvements for best-effort traffic. Energy effciency is an important issue for optical network since they must rely on their batteries. We present a novel MAC protocol that achieves a good energy efficiency of optical interface of the network and provides support for diverse traffic types and QoS. The scheduler of the base station is responsible to provide the required QoS to connections on the optical link and to minimise the amount of energy spend by the High speed Network. The main principles of the MaC protocol are to avoid unsuccessful actions, minimise the number of transitions , and synchronise the mobile and the base-station. We will show that considerable amounts of energy can be saved using these principles.