• Electronics and Telecommunications Trends
• /
• v.35 no.2
• /
• pp.69-78
• /
• 2020

Small portable devices such as mobile phones and laptops currently display a trend of high power consumption owing to their characteristics of high speed and multifunctionality. Low-power SoC design is one of the important factors that must be considered to increase portable time at limited battery capacities. Popular low power SoC design techniques include clock gating, multi-threshold voltage, power gating, and multi-voltage design. With a decreasing semiconductor process technology size, leakage power can surpass dynamic power in total power consumption; therefore, appropriate low-power SoC design techniques must be combined to reduce power consumption to meet the power specifications. This study examines several low-power SoC design trends that reduce semiconductor SoC dynamic and static power using EDA tools. Low-power SoC design technology can be a competitive advantage, especially in the IoT and AI edge environments, where power usage is typically limited.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.8
• /
• pp.99-105
• /
• 1995

This paper provides a highly efficient grinding for ferrous materials using ELID-grinding method. The grinding efficiency using ELID gring method with CIFB-cBN wheel and CB-cBN wheel is compared with general grinding method with V-cBN wheel. This paper measured grinding ratio for plunge grinding and grinding resistance for traverse grinding in order to investigate grinding ability. The results show that ELID grinding methods is useful for the high efficient grinding of ferrous materials.

• Journal of Sensor Science and Technology
• /
• v.15 no.6
• /
• pp.386-390
• /
• 2006

This paper describes the ohmic contact formation of polycrystalline 3C-SiC films deposited on thermally grown Si wafers. In this work, a TiW (titanium tungsten) film as a contact material was deposited by RF magnetron sputter and annealed with the vacuum process. The specific contact resistance (${\rho}_{c}$) of the TiW contact was measured by using the C-TLM (circular transmission line method). The contact phase and interfacial reaction between TiW and 3C-SiC at high-temperature as also analyzed by XRD (X-ray diffraction) and SEM (scanning electron microscope). All of the samples didn't show cracks of the TiW film and any interfacial reaction after annealing. Especially, when the sample was annealed at $800^{\circ}$ for 30 min., the lowest contact resistivity of $2.90{\times}10{\Omega}cm^{2}$ was obtained due to the improved interfacial adhesion. Therefore, the good ohmic contact of polycrystalline 3C-SiC films using the TiW film is very suitable for high-temperature MEMS applications.

• Journal of IKEEE
• /
• v.11 no.4
• /
• pp.272-278
• /
• 2007

In this paper, we report on the 2D (two-dimensional) simulation result of the DC (direct current) electrical and thermal characteristics of AlGaN/GaN HEMTs (high electron mobility transistors) grown on Si substrate, in comparison with those grown on sapphire and SiC (silicon carbide) substrate, respectively. In general, the electrical properties of HEMT are affected by electron mobility and thermal conductivity, which depend on substrate material. For this reason, the substrates of GaN-based HEMT have been widely studied today. The simulation results are compared and studied by applying general Drift-Diffusion and thermal model altering temperature as 300, 400 and 500 K, respectively. With setting T=300 K and $V_{GS}$=1 V, the $I_{D,max}$ (drain saturation current) were 189 mA/mm for sapphire, 293 mA/mm for SiC, and 258 mA/mm for Si, respectively. In addition, $G_{m,max}$ (maximum transfer conductance) of sapphire, SiC, Si was 38, 50, 31 mS/mm, respectively, at T=500 K.

• Elastomers and Composites
• /
• v.42 no.1
• /
• pp.47-54
• /
• 2007

Reaction kinetics of polyurethane elastomers (PU) were studied using dynamic DSC and TGA for three PU samples of general purpose (Sample A), high temperature cross-likable CASE purpose with MOCA (Sample B), and RT cross-likable CASE purpose grade (Sample C). From DSC results, sample with MOCA(Sample B) showed lower shift of peak temperature, while showing broader thermograms than those of general purpose grade (Sample A). On the other hand, RT cross-linkable PU grade (Sample C) showed an interesting double mode reaction patterns, i.e., a lower temperature reaction at about $70\;^{\circ}C$, and a higher temperature reaction in the range of $140{\sim}170\;^{\circ}C$, indicating that it requires 2-step reaction process in order to complete the reaction. Once the cross-linking reaction completed, however, TGA results showed that all the samples would be considered to have similar chemical structures, showing similar decomposition processes. Sample C, especially, had showed decomposition properties of both Sample A and Sample B. Formation activation energies calculated from Kissinger method showed 10.39, 65.85, 36.52(Low $T_p$) and 18.21(High $T_p$) kcal/mol, while decomposition activation energies were 31.94, 30.84, 24.16 kcal/mol, respectively.

• Journal of the Korean Ceramic Society
• /
• v.36 no.7
• /
• pp.698-704
• /
• 1999

Li rich Li1+xMn2-xO4(x=0.07) spinel powders were prepared by an oxalate precipitation of wet chemical methods at temperature lower than $600^{\circ}C$. The FTIR results showed that the powders prepared at $600^{\circ}C$ had high degree of crystal quality comparing with the spinel powders prepared by solid state reaction at 75$0^{\circ}C$ which was the lowest synthesis temperature of the solid state reaction method. The particle size of powders prepared by the oxalate precipitation at $600^{\circ}C$ was smaller than 0.2${\mu}{\textrm}{m}$ and the specific surface area was 11.01 m2/g A heat treatment over 90$0^{\circ}C$ formed second phase in the precipitates. It was shown that there were phase transitions at temperatures. T1,T2 and T2. The transitions involved weight loss and gain during heating and cooling. The low temperature synthesis below $600^{\circ}C$ avoided the second phase formation and the prepared powders showed improved compositional and physical properties for secondary lithium battery applications.

• Fisheries and Aquatic Sciences
• /
• v.27 no.2
• /
• pp.122-135
• /
• 2024

Obesity is a disease involving mechanisms of fat accumulation, low-grade inflammatory cytokine release, and mitochondrial dysfunction. The aim of the current study was to investigate the effects of abalone intestine extract on fat metabolism in 3T3-L1 adipocytes and high fat diet-induced zebrafish larvae. The total phenol content was highest in subcritical water extract at 210℃ (SW210) among hot water, ethanol, and subcritical water extracts of abalone intestine. In addition, SW210 of male abalone intestine (MASW210) most effectively controlled the lipid accumulation and expression of adipogenic or lipogenic regulators (PPAR-γ, C/EBPα, SREBP-1c, and FAS) in 3T3-L1 adipocytes. Likewise, in zebrafish larvae fed high fat, MASW210 significantly suppressed body weight, glucose levels, and lipid accumulation. The mRNA expression related to adipogenesis (PPAR-γ and C/EBPα), lipogenesis (SREBP-1c and FAS), inflammatory cytokines (TNF-α and IL-6), energy m/;.etabolism (AMPK, lepr, SIRT1, and adiponectin), and mitochondrial biogenesis (PGC-1α and CPT-1) were significantly regulated by treatment with MASW210. These results suggest that abalone intestine extract such as MASW210, are useful biomaterials for improving obesity and metabolic diseases.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.7
• /
• pp.462-469
• /
• 2015

This study was carried out to examine characteristics of various acoustic indicators evaluating speech intelligibility such as reverberation time(T₃₀), D₅₀, C₅₀ and speech transmission index(STI) in Korean elementary school classrooms. Results showed that mean T₃₀ at middle frequencies(500 Hz to 2000 Hz) measured in 9 classrooms was about 0.75 s, which exceeds a regulation specified on American National Standards(ANSI); 0.60 s. Mean D₅₀, C₅₀ and STI were 60 % to 66 %, +2 dB to +3 dB, and 0.65, respectively. The maximum difference in D₅₀ and C₅₀ according to different receiver points in a classroom was 13 % and 2.5 dB, while the maximum difference in T₃₀ was 0.03 s. Whereas STI measured in classrooms has relatively low correlation with other indicators, correlation between D₅₀ and C₅₀ was high, R²=.9964. In addition, T₃₀ and C₅₀ were fitted well as logarithmic regression curve with R²=.9610. It was +3.73 dB in C₅₀ and 68 % in D₅₀ which are the value corresponding to 0.60 s in T₃₀ on this curve.

• Journal of the Korean Magnetics Society
• /
• v.16 no.1
• /
• pp.28-33
• /
• 2006

La substituted perovskite $BiFeO_3$ have been prepared by a sol-gel method. Magnetic and structural properties of the powders were characterized with Mossbauer spectroscopy, XRD, SEM, and TG-DTA. The crystal structure is found to be a rhombohedrally distorted perovskite structure with the lattice constant $\alpha=3.985{\AA}\;and\;\alpha=89.5^{\circ}.\;Bi_{2/3}La_{1/3}FeO_3$ powders that were annealed at and above $600^{\circ}C$ have a single-phase perovskite structure. However, powders annealed at $900^{\circ}C$ have a typical perovskite structure with small amount of $Bi_2O_3$ phase. The Neel temperature of $Bi_{2/3}La_{1/3}FeO_3$ is found to be $680\pm3K$. The isomer shift value at room temperature is found to be 0.27 mm/s relative to the Fe metal, which is consistent with high-spin $Fe^{3+}$ charge states. Debye temperature far$Bi_{2/3}La_{1/3}FeO_3$ is found to be $305\pm5K$. The average hyperfine field $H_{hf}(T)$ of the $Bi_{2/3}La_{1/3}FeO_3$, shows a temperature dependence of $[H_{hf}(T)-H_{hf}(0)]/H_{hf}(0)=-0.42(T/T_N)^{3/2}-0.13(T/T_N)^{5/2}$ for $T/T_N<0.7$ indicative of spin-wave excitation.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.2
• /
• pp.46-52
• /
• 2001

In this paper, the real-time prediction of high temperature creep life was carried out for the friction welded joints of dissimilar heat resisting steels (SUH3-SUH35). various life prediction method such as LMP (Larson_miller Parameter) and ISM (initial strain method) were applied. The creep behaviors of those steels and the welds under static load were examined by ISM combined with LMP at 500, 600 and $700^{\circ}C$, and the relationship between these two methods was investigated. A real-time creep lie (tr, hr) prediction equation by initial strain (${\varepsilon}_0$, %) under any creep stress ($\sigma$, MPa) at any high temperature (T, K) was developed as follows: $t_r={\alpha}{\varepsilon}_0^{\beta}{\sigma}^{-1}$ where, ${\phi}=16: {\alpha}=10^{51.412-0.104T+5.375{\times}10^5T^2}$, $ {\beta}=-83.989+0.180T-9.957{\times}10^{-5}T^2,{\phi}=20:$ ${\alpha}=10^{69.910-0.146T+7.744{\times}10^{-5}T^2$, ${\beta}=-51.442+0.105T-5.595{\times}10^{-5}T^2$ for SUH3-SUH35 friction weld of =16mm and 20mm, respectively.