• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.23-26
• /
• 2007

A preliminary， study of low temperature condition was performed to simulate high altitude condition. The mixed air temperature were investigated at various condition by experiments using cryogenic air by heat exchanger and normal temperature air. An experimental setup was constructed to simulate low temperature condition with liquid nitrogen. To control mass flow rate, orifice and pressure regulators were used. The experimental results show that the mixed air temperature increases linearly with mass flow rate of normal temperature air. Therefore it can be help to simulate a low temperature condition of high altitude.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.43-43
• /
• 2017

During grain filling period, rice is affected by many environmental factors; including temperature, water, radiation and soil nutrition condition. In future climate, greater shading and heat tolerance will be required in rice. In this study, the effect of shading and high temperature on spikelet sterility was conducted on fourteen Vietnamese cultivars. Field experiments were studied in 2015 and 2016 to evaluate the response of Vietnamese cultivars under high temperature during grain filling stage. The high temperature and shading were applied by closing two sides of growth chamber and covered by a black cloth (50% reduced solar radiation) under the field condition after the first cultivar heading. The sterility increased significantly under high temperature and shading. The highest percentage sterile spiketlets was observed in 'Jasmine 85' (71.7%) under shading and in 'OM4900' (53.4%) under high temperature in 2015 and 2016, respectively. Among the treatments, the percentage of sterile spekelets in Vietnamese cultivars under shading was highest which was 54.9% and 41.8% in 2015 and 2016, respectively. Yield components reduced significantly in both of shading and high temperature. Corresponding with significantly decrease in yield components, the yield in high temperature and shading decreased strongly in both 2015 and 2016.

• The Korean Journal of Ceramics
• /
• v.4 no.1
• /
• pp.5-8
• /
• 1998

Flat belt(FB) type high pressure apparatus has been succesfully utilized in various high pressure experimental stations in Korea and Japan to conduct HPHT (high pressure and high temperature) diamond synthesis. Present paper discusses pressure calibration of FB apparatus at high temperature to establish P-T condition of diamond synthesis. We also present some examples of controling P-T condition through careful experimental set-up of the high pressure sample cells. Finally we discuss reproducibility of pressure and temperature condition of the HPHT diamond synthesis.

• Corrosion Science and Technology
• /
• v.7 no.1
• /
• pp.61-67
• /
• 2008

In this paper, electrochemical and microstructural characteristics of nickel-plated Alloy 600 were investigated in order to identify the performance of electroless Ni-plating on Alloy 600 in high-temperature aqueous condition with the comparison of electrolytic nickel-plating. For high temperature corrosion test of nickel-plated Alloy 600, specimens were exposed for 770 hours to typical PWR primary water condition. During the test, open circuit potentials (OCP's) of all specimens were measured using a reference electrode. Also, resistance to flow accelerated corrosion (FAC) test was examined in order to check the durability of plated layers in high-velocity flow environment at high temperature. After exposures to high flow rate aqueous condition, the integrity of surfaces was confirmed by using both scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). For the field application, a remote process for electroless nickel-plating was demonstrated using a plate specimen with narrow gap on a laboratory scale. Finally, a practical seal design was suggested for more convenient application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.05a
• /
• pp.30-33
• /
• 1994

This paper studies on the effect of DSC(Differential Scanning Calorimeter) analysis condition on the glass transition temperature of silica filled epoxy network polymer used for ultra-high voltage apparatus. The effects of temperature scanning rate specimen size and gas flow rate on measured glass transition temperature have been studied in order to select optimum thermal analysis condition.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.12
• /
• pp.1-8
• /
• 2012

The performance and lighting characteristics of the LED depend on cooling condition because the power LED generates lots of heat. In this paper, the effect of the generated heat from power LED module on lighting characteristics and performance is measured and evaluated. For experiments, the transient temperature of a power LED module with cooling condition is measured. In addition, the temperature and lighting characteristics of the LED module are measured during the steady state. As a result, the cooling condition is less effective on the lighting characteristics of the LED module at rated current but the cooling condition extremely affects those of the LED module over the rated current. Because high temperature of the power LED module causes the low phosphor conversion, luminance efficiency becomes low and color temperature becomes high. When power LED module are driven over the rated condition, higher temperature is directly related to lighting characteristics and performance of the LED module rather than higher current.

• Journal of the Korean Society of Safety
• /
• v.5 no.1
• /
• pp.31-39
• /
• 1990

In this paper, the influence of the table speed, metal removal rate and grinding fluid on long wheel workpiece contact zone at high effect grinding was investigated by theoretical analyses and measuring the temperature, and discussed by the temperature distribution in grinding surface layer. Main results obtained are as follows, 1) Rega.dless of the table speed, the temperature gap of the workpiece(heat influx) is about 6-8 times as high in dry condition as in wet condition. 2) Good grinding condition can be obtained owing to the effect of grinding fluid without any burning defect under the condition of the metal removal rate(1.0mm$^3$/mm.s) in case of wet grinding. 3) When the depth from the surface layer is about 1.25-1.5mm under the condition of the slow table speed, surface temperature goes up higher as the table speed slows down, because long contact time is laked at the surface layer. 4) In case of the same metal removal rate, the lower the table speed becomes, the higher the surface temperature is, because grinding depth has a far more influence on wheel workpiece contact zone than the table speed.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.86-87
• /
• 2017

The high-temperature creep of Ultra-High-Strength Concrete (UHSC) has been investigated in this study. The purpose of this study is to evaluated total strain and high-temperature creep at elevated temperatures under loading condition of UHSC. As results, Total strain of UHSC increased showing shrinkage with increasing compressive strength. The high-temperature creep of UHSC increased with the temperature and higher level of compressive strength showed bigger high-temperature creep.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.24 no.2
• /
• pp.35-41
• /
• 1979

To observe the effects of temperature and photoperiod on the growth and yield of winter wheat (Triticum aestivum, L) eight varieties including Chang Kwang were tested at various treatments like longday-high temperature (24hrs-20\circ), shortdayhigh temperature (12hrs-20\circ), longday-low temperature (24hrs-14\circ) and shortday-low temperature (12hrs-14\circ). Among the traits measured, days to heading, plant height, spike length, number of spikes per hill and grain yield per hill were generally decreased at high temperature and long day treatment and increased at low temperature and shortday condition. Number of grains per spike was decreased at low temperature and short day condition while increased at longday and high temperature conditions. Grain weight was decreased significantly at high temperature and shortday while increased at low temperature and longday treatment.

• Transactions of Materials Processing
• /
• v.8 no.6
• /
• pp.576-582
• /
• 1999

The high temperature behavior of Al 6061 alloy was characterized by the hot torsion test in the temperature ranges of 400∼550℃ and the strain rate ranges of 0.05∼5/sec. To decide optimum deformation condition, three types of deformation maps were individually made from the critical strain (εc). deformation resistance(σp) and deformation efficiency (η). The critical strain(εc) for dynamic recrystallization (DRX) which was decided from the inflection point of strain hardening rate(θ) - effective stress (σ) curve was about 0.65 times of peak strain (εp). The relationship among deformation resistance (peak stress, σp), strain rate (ε), and temperature (T) could be expressed by ε=2.9×1013[sinh(0.0256σp]7.3exp (-216,000/RT). The deformation efficiency (η)which was calculated on the basis of the dynamic materials model (DMM) showed high values at the condition of 500∼550℃, 5/sec for 100% strain. The results from three deformation maps were compared with microstructures. The best condition of plastic deformation could be determined as 500℃ and 5/sec.