• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.7
• /
• pp.1061-1067
• /
• 2008

Direct Torque Control[DTC] and Vector Control are the two schemes developed for high performance induction motor drives. DTC based induction motors are being increasingly used in various industrial applications. DTC offers fast torque response and better speed control with lesser hardware and processing costs as compared to vector controlled drives. However, conventional DTC suffers from high torque ripple, current harmonics and low performance during torque transients. In this paper a new Direct Torque Control[DTC] method of induction motor is presented. In comparison with the conventional DTC method, the PWM technique is applied to proposed control method. In this method, decoupling mechanism is not required and the torque, the flux magnitude are under control using PI controllers and generating the voltage command for inverter control. Therefore torque and speed ripple could be reduced in comparison with the conventional switching table DTC.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.6
• /
• pp.407-413
• /
• 2013

In the conventional towing tank, the ordinary towing carriage has a speed barrier which caused not only by the limitation of the length of towing tank but also the limitation of acceleration. Therefore the length of the towing tank should be decided carefully from the planning stage of the towing tank construction. Consequently the acceleration of the towing carriage should be taken less than 0.06g practically to avoid the slip of the wheel on rail. Due to the increasing demand of the high speed experiments on the development of special novel ship, the requirement of the high speed towing carriage is continuously increased recently. When the minimum measuring time of the towing experiment is prescribed as five seconds, the carriage should be accelerated with higher than 0.12 g to get the speed of 18 m/sec even in the towing tank having a length of 400m in length approximately. This means that the requirement of acceleration is bigger than twice of the ordinary practices of carriage acceleration. In such a condition the exerted total power of motor could not converted to traction force for the acceleration of the carriage without slip. To over come these difficulties a pair of horizontal traction wheels are reinforced to each of the ordinary vertical carrier wheel and appropriate suspension system has been devised for the towing tank of super high speed operation. It is believed that the design of novel suspension system adaptable for the high speed acceleration of towing carriage will play a important role as a reference for the remodeling of the towing tank for high speed experiment.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.1
• /
• pp.68-74
• /
• 2008

This study is concerned with the development of the basic planing hull form of small fishing boat in 25 knots high speed. A series of model test to determine the optimum performance hull form of actual fishing boat with 10 gross tonnage was carried out for 5 models made available planing hull form in the circulation water channel. Model test was performed with the resistance test to study the hydrodynamic characteristics of model ships and the sinkage and trim measurement to investigate the stability of model ships and also the wave pattern observation to analyze the effectiveness of model ships. As the result, the planing hull form of P-4 with deep V type bow can be derived as the best hull form with good performance especially in ship's resistance efficiency showing less residual resistance and sinkage and trim and the spray effect, etc..

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.4
• /
• pp.305-310
• /
• 2016

This study identified necessary navigational support services to prevent accidents through an examination and a survey on the navigation and communication systems of non-SOLAS ships. The functional and operational requirements for the identified navigational support services were discussed accordingly. Among the navigational support services proposed are an Electronic Navigational Chart (ENC) service, a route planning service, an operation monitoring service, and collision prevention support services for ships in coastal areas. To facilitate the identified navigational support services, ship navigation system, shore supporting centre and maritime communication network were discussed as a digital infrastructure. The operational methode for the digital infrastructure were discussed in the service scenarios for ships carrying dangerous cargo, large ships over 200 meters in length and high speed passenger ships over 15 knots in speed. This study will facilitate the development of policies for the improvement of ship operation management in Korean coastal waters and will contribute to improving the navigational safety of non-SOLAS ships.

• Journal of Navigation and Port Research
• /
• v.31 no.10
• /
• pp.813-818
• /
• 2007

There are the C.W.C and Towing Tank to the model-test equipments of the boat. A model testing of the high speed boat have a difficult in the performance verification because of very a small the scale-ratio of the ship-model and restricted by flow-velocity of the C.W.C and X-carriage velocity of the T.T. In general, the stepped hull boat is a high of fuel-efficiency because of the resistance reduction by a small wetted surface-area in correspond without stepped-hull boat. But It have a tendency to be bad the rolling performance by reduced stern wetted-area In this paper, the high speed stepped planning-boats with & without attached a stern body were performed to compare the effect of resistance and rolling performance by using sea model-test method.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.3
• /
• pp.202-210
• /
• 2013

As incomes increase, interest in ocean leisure picks up. As a result, a lot of research and developments on hull form design and production of planing boats, mostly used for ocean leisure, are needed. Analysis in researches on resistance of planing boats shows that resistance characteristic of planing boats is different from resistance characteristic of general boats because the former is fast, and its wetted surface is very small. Using Savitsky formula widely used in the calculation of effective horse power in shipbuildingyards, and propulsion system and engine manufacturers, this study calculated total resistance of a research planing boat. Then it analyzed the flow characteristics of the planing boat through theoretical analysis and wind tunnel experiment, and computed air resistance and lift force by changes of speed and trim angle. It also compared and analyzed result of theoretical analysis and experiment of the ratio of air resistance to total resistance under variations of velocity and trim angle. When the study is used to estimate more accurate effective horse power, it is expected to remedy abuses of unnecessarily installing high-powered engine. As nature disasters due to abnormal changes of weather increase, interest in greenhouse gas grows. International Maritime Organization (IMO) legislated Energy Efficiency Design Index (EEDI) and Energy Efficiency Operational Indicator (EEOI) to reduce ship greenhouse gas emissions. But this index will be applied to over 400 tons ships, small ships, emitting more greenhouse gases than larege ships per unit power, will dodge the regulations. Thus, this study indicated a problem by calculating greenhouse gas emissions of an ocean leisure planning boat (a small ship), and suggested the need for EEDI of small ships.