• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.113-121
• /
• 1995

This study deals with the quality and the optimum range of laser cutting process. Cold rolled steel sheets for automobile application were cut by a high power CO$_{2}$ laser system with beam quality of TEM$_{\infty}$ mode. Both process parameters such as travel speed and assist gas pressure, and quality factors were considered to optimize the laser cutting. It was revealed that the thinner the sheet thickness, the less effect of oxidation energy for contributing the cutting process. High speed photographs demonstrated that molten spot on the cut surface moved in a random and vigorous manner according to its viscosity and the flowing direction of assist gas, which resulted in so called striation. Laser cutting produced a very smooth surface of average roughness(Ra) about less than 1.5.mu.m at the optimum range. It was also shown that the characteristics of dross formation was influenced by the flowing durection of assist gas and the fluidity of molten metal drop..

• 동력기계공학회지
• /
• 제6권4호
• /
• pp.43-48
• /
• 2002

This paper presents a seam tracking controller of high speed rotating arc sensor developed by microprocessor based system. The seam tracking algorithm is based on the average current value at each interval region of four phase points on one rotating cycle. To remove the noise effect for the measured current, the area during one rotating cycle is separated into four regions of front, rear, left and right. The average values at each region are calculated, using the regional current values and a low pass filter incorporating the moving average and exponential smoothing methods is adopted. The effectiveness is proven through the experimental results for several kinds of welding condition.

• Journal of Welding and Joining
• /
• 제34권3호
• /
• pp.6-11
• /
• 2016

Joining Al/Fe dissimilar metals is becoming a subject of special interest in the assembly of automotive parts as a trade-off between the weight lightening and the cost reduction. Although various studies have been introduced to join Al alloy with the steel sheet by fusion welding, weak joint strength and galvanic corrosion still remained as problems to be solved. As a solid state welding, friction stir welding has been preferred to fusion welding processes in the dissimilar metal joints. This study investigated friction stir spot welding (FSSW) of Al alloy to the thin steel sheet with a thickness of 0.65 mm. The conventional FSSW is a stationary spot welding process but new approach adopted an additional circumferential movement in company with high speed tool rotation. A full factorial experimental design was implemented, and the main and interaction effects of parameters were analysed on the failure load in the tensile shear test. The direction and radius of rotation were statistically significant parameters and these two parameters affected the joint width and the shape of the hook.

• Journal of Welding and Joining
• /
• 제24권4호
• /
• pp.22-26
• /
• 2006

In lap welding of zinc-coated steel, porosity formation is one of most significant weld defects, which is caused by zinc vapor generated between the steel sheets. Various solutions have been proposed in the past years but development of more effective method is a worthwhile subject to be investigated. In this study, autogenous laser welding and laser-TIG hybrid welding was applied to the lap welding of zinc-coated steel without gap, and weld pool behaviors were observed by using high speed camera and the porosity generation mechanism was analyzed. The weld defects were successfully eliminated by laser-TIG hybrid welding. This is because the leading TIG arc partially melted the upper sheet and vaporized/oxidized the coated zinc on the lapped surfaces prior to the trailing laser illuminating the specimen.

• Journal of Welding and Joining
• /
• 제30권5호
• /
• pp.40-45
• /
• 2012

Nowadays in Republic of Korea, whole amount of the thermite welding powder for rail joinning is dependent on import. However the demand of the thermite welding powder would be enlarge because some constructing high-speed train and city metro projects are currently in progress. In addition this is the main reason why we should develop the thermite welding powder, domestically. This study is focused on utilizing the recyclable materials like Al powders from cans and iron oxide scales from wire rods as the main components of the thermite welding powder. By minimizing Al content in weld zone by controlling the mixing ratio of the Al powder in the thermite welding powder, the excessive dissolution of the Si and Mn components came from the Al powders could be controled. The tensile strength of welding zone in welded rail was 740 MPa, with that the developed thermite welding powder.

• Journal of Welding and Joining
• /
• 제34권2호
• /
• pp.67-72
• /
• 2016

Aluminum alloy is one of light weight material and it is used to make LNG tank and ship. However, in order to weld aluminum alloy high density heat source is needed. In this paper, I-butt welding of Al 5083 with 6mm thickness using Plasma-MIG welding was carried out. The experiment was performed to investigate the influence of plasma-MIG welding parameters such as plasma current, wire feeding rate, MIG-welding voltage and welding speed on the tensile strength of weld. In addition we suggested 3 strength estimation models which are second order polynomial regression model, multiple nonlinear regression model and neural network model. The estimation performance of 3 models was evaluated in terms of average error rate (AER) and their values were 0.125, 0.238, and 0.021 respectively. Neural network model which has training concept and reflects non -linearity was best estimation performance.

• Journal of Welding and Joining
• /
• 제17권1호
• /
• pp.77-81
• /
• 1999

Through-hole PCB(Printed Circuit Board) was soldered by flow soldering process using cleaning or noncleaning fluxes. Preheating temperature and conveyor speed were changed in the range of 323∼413K and 0.3∼2m/min respectively. The soldered joints were tensile tested in order to evaluated bonding strength. As experimental results, relatively high tensile fracture load, 120∼140N, were obtained in case of preheating temperature of 383K, and conveyor speed was 0.6∼1.0 m/min. Fractured surfaces of higher tensile strength show some dimple area, while those of lower tensile fracture load show brittle fracture.

• Journal of Welding and Joining
• /
• 제25권1호
• /
• pp.42-48
• /
• 2007

For high performance and structural stability, application of high strength steel has continuously increased. However, the change of the base metal gives rise to problems with the accuracy management of the welded structure. It is attributed to the martensite phase transformation of the high strength low alloy steel weldment. The purpose of this study is to establish the predictive equation of transverse shrinkage and residual stress for the HY-100 weldment. In order to do it, high speed quenching dilatometer tests were performed to define a coefficient of thermal expansion(CTE) at the heating and cooling stage of HY-100 with various cooling rates. Uncoupled thermal-mechanical finite element(FE) models with CTE were proposed to evaluate the effect of the martensite phase transformation on transverse shrinkage and residual stresses at the weldment. FEA results were verified by comparing with experimental results. Based on the results of extensive FEA and experiments, the predictive equation of transverse shrinkage and longitudinal shrinkage force at the HY-100 weldment were formulated as the function of welding heat input/in-plane rigidity and welding heat input respectively.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.585-590
• /
• 1999

The conventional $CO_2$ inverter arc machine has constant voltage output characteristic and uses constant wire speed controller for welding current control. By adoption of PWM inverter to the welding machine, the spattering was reduced rather than the thyrister arc welding machine or AC arc welding machine. Moreover, by the high switching frequency, the output reactor size could be reduced evidently. Recently, the studies on optimal voltage and current waveform for the welding performance improvement have been studied. In this paper, a new instantaneous output current control scheme during the short circuit mode was proposed and showed the capability of arc stability improvement and the reduction of spatter generation.

• 한국레이저가공학회지
• /
• 제10권4호
• /
• pp.7-12
• /
• 2007

The aluminized steel sheet exhibits excellent resistance to oxidation and corrosion, and can substitute for stainless steel or heat-resisting steel in some situations. Furthermore it has wide applications, owing to its low cost and excellent performance, in the petrochemical industry, electric power, other energy conversion system, etc. and has attracted the attention of many investigators. Laser welding is a remarkably advantageous method for welding of thin sheets and surface-treated steel sheets since the method requires less heat input, and it is suitable for high-speed welding. In this study, thus, the laser weldability of aluminized steel sheet was investigated. As the result from the study, there is an Al-rich zone in a welded part which has decreased the welding strength due to the intermetallic compounds in the Al-rich zone.