• 전기학회논문지
• /
• 제57권3호
• /
• pp.390-397
• /
• 2008

Permanent Magnet Linear Synchronous Motor (PMLSM) has high efficiency, high energy density, and high control-ability. But, the detent force always is produced by the structure of slot-teeth. There are the disadvantages such as noise and vibration of the apparatuses are induced and the control ability is curtailed because detent force acts as thrust ripple. Therefore, the detent force reduction is an essential requirement in PMLSM. Generally, the method, skewing permanent magnet or slot-teeth, is used to reduce the detent force. But the thrust is decreased at the same time. If permanent magnet is skewed, the lateral force which operates as the perpendicular direction of skew direction is generated in linear guide of PMLSM. So, V-skew model is proposed for the reduction of lateral force. The lateral force acts as braking force in linear motion guide, and it has bad influence to the characteristics of PMLSM. However, these problems will not be solved by 2-dimensional Finite Element Analysis (FEA). So, in this paper 3-dimensional FEA is applied to analyze the PMLSM where permanent magnet is skewed and has overhang. The detent force and thrust characteristics considering skew and overhang effects of permanent magnet are analyzed by 3-dimensional FEA and the results are compared with experimental values to verify the propriety of analysis.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권12호
• /
• pp.659-663
• /
• 2002

The brake systems of high-speed train are to be equipped with three different brake systems, such as regenerative brake with regenerative feedback in driving car, a pneumatic disc brake, and non-contact linear eddy-current brake(ECB). The regenerative brake and the pneumatic disc brake are acting on the wheels. Their achievable braking force depends on the adhesive coefficient, which is influenced by the weather condition and speed, between the wheel and The linear eddy current brake gets an economical solution in the high-speed train because of the independence of the adhesive coefficient, no maintenance needed. and the good control characteristics. The braking force and the normal force of ECB for korean high-speed train are analysed by the 2D FEM(Finite Element Method). Finally the normal force is compared with the experiential values to verify the analysis.

• 한국정밀공학회지
• /
• 제13권4호
• /
• pp.122-128
• /
• 1996

In high speed and high precision assembly systems such as a surface mounting device and robotend effector, the contact force control is required. As the operation repeats, the repetitive control is applied to reduce the periodic contact force errors. Since high order unmodelled dynamics are easily excited in contact force control, a Q filter was introduced and its robust stability was analyzed. Simulation and Experimental results show the effectiveness of the algorithm.

• 한국강구조학회 논문집
• /
• 제25권4호
• /
• pp.409-419
• /
• 2013

인장력을 받는 고력볼트로 체결된 T-stub는 지레작용력과 부재 사이의 접촉력 등의 영향을 받는다. 이러한 지레작용과 부재 사이의 접촉력 등이 고려된 설계식이 제안되지 않는 경우, 인장력을 받는 T-stub는 예측한 설계강도 보다 더 작은 강도에도 파괴될 가능성이 있다. 이를 방지하기 위하여 지금까지 많은 연구를 통하여 고력볼트로 체결된 T-stub의 지레작용력과 부재 사이의 접촉력 예측모델이 제안되었다. 그러나 아직도 우리나라에서는 이를 반영한 설계식의 제안이 이루어지고 있지 않다. 따라서 이 연구는 3차원 비선형 유한요소해석법을 적용하여 그동안 제안된 예측모델을 개선한 보다 정확한 지레작용력 및 접촉력 예측모델을 제안하고자 진행하였다. 3차원 비선형 유한요소 해석 결과, 이 연구에서 제안한 지레작용력 및 접촉력 예측모델은 기존의 예측모델보다 더 근사적인 예측값을 제공하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1083-1086
• /
• 2003

Recently, the study on bearingless motors which integrate both motor and magnetic bearing function in one stator is very active, as many machines have high rotational speed, high precision, smaller size and lighter weight. In this paper, we propose a novel rotary actuator including function of axial bearing using Lorentz force as a preceding research for development of a bearingless motor. As using Lorentz force, this type has some merits such as the linearity of control force, freedom from flux saturation and high efficiency unlike conventional rotary actuators using a reluctance force. This type is cotrolled independently in levitation and rotational directions respectively. It shows by mathematical expression of levitation force and torque in the proposed rotary actuator. And also, the levitation force is generated by magnetic interaction between the magnetic materials and the rotational torque is generated by Lorentz force. Finally. for verification of this proposed system, a prototype is made and some experiments will be performed in the near future.

• Wind and Structures
• /
• 제19권5호
• /
• pp.565-583
• /
• 2014

Using synchronous surface pressures from the wind tunnel test, the three dimensional wind load models of high-rise buildings are established. Furthermore, the internal force responses of symmetric high-rise buildings in along-wind, across-wind and torsional directions are evaluated based on mode acceleration method, which expresses the restoring force as the summation of quasi-static force and inertia force components. Accordingly the calculation methods of equivalent static wind loads, in which the contributions of the higher modes can be considered, of symmetric high-rise buildings in along-wind, across-wind and torsional directions are deduced based on internal forces equivalence. Finally the equivalent static wind loads of an actual symmetric high-rise building are obtained by this method, and compared with the along-wind equivalent static wind loads obtained by China National Standard.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.145-152
• /
• 2004

The flow stress value was calculated by comparing predicted and measured roll force. Using basic on-line roll force model and logged mill data the flow stress equation of high strength steel for automobile was derived. The flow stress equation consists of the flow stress equation of carbon steel and flow stress factor calculated by neural network with input parameters not only carbon contents, strip temperature, strain, and strain rate, but also compositions such as Mn, p, Ti, Nb, and Mo. Using the flow stress equation and basic roll force model, precision roll force model of high strength steel for automobile was derived. Using test set of logged mill data the flow stress equation was verified.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 창립기념 춘계학술대회 논문집
• /
• pp.556-563
• /
• 1998

Railway bridges have a significant effect on the stress and displacement of continuous welded rail(CWR). Longitudinal compression force at high temperature, combined breaking or acceleration forces can introduce track buckling. On the other hand, longitudinal tensile forces, associated with low temperatures, in combination with breaking forces may break rail. Therefore, it is very important to work out thorough counter measures for those problems, specially in high speed rail which high safety is required. The exact evaluation of longitudinal force of rail has the key to the solution. The main aim of the present paper is to examine whether the longitudinal force of CWR's on Kyung-Bu-HSR satisfy the criteria to be fulfilled in the design of railway bridge. The analyses are carried out by using "CWRAP" program which was developed by our research group. The ballast resistance and breaking force effects on the longitudinal force of CWR are investigated.

• Journal of Mechanical Science and Technology
• /
• 제14권8호
• /
• pp.867-878
• /
• 2000

In order to study unsteady aerodynamic loads on high speed trains passing by each other 350km/h, three-dimensional flow fields around trains during the crossing event are numerically simulated using three-dimensional Euler equations. Roe's FDS with MUSCL interpolation is employed to simulate wave phenomena. An efficient moving grid system based on domain decomposition techniques is developed to analyze the unsteady flow field induced by the restricted motion of a train on a rail. Numerical simulations of the trains passing by on the double-track are carried out to study the effect of the train nose-shape, length and the existence of a tunnel on the crossing event. Unsteady aerodynamic loads-a side force and a drag force-acting on the train during the crossing are numerically predicted and analyzed. The side force mainly depends on the nose-shape, and the drag force depends on tunnel existence. Also. a push-pull (i.e.impluse force) force successively acts on each car and acts in different directions between the neighborhood cars. The maximum change of the impulsive force reaches about 3 tons. These aerodynamic force data are absolutely necessary to evaluate the stability of high speed multi-car trains. The results also indicate the effectiveness of the present numerical method for simulating the unsteady flow fields induced by bodies in relative motion.

• 비파괴검사학회지
• /
• 제12권4호
• /
• pp.26-31
• /
• 1993

In this paper, the axial force of high tension bolt is measured by using ultrasonic wave. In the case of the different materials the conclusion obtained are as follows : (1) The relation of the material quality of each high tension bolt and form(diameter or section area), and yield axial force can be observed. (2) As 0.1 is devided by the apparent elongation the measurement accuracy of high tension bolt can be achived. Also, it is founded that the Joint axial force of high tension bolt is determined by the yield force.