• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.10
• /
• pp.61-70
• /
• 2006

A Supersonic air intake model was designed for the high performance ramjet and dual-mode scramjet engine to operate at Mach 4 flight condition. The air intake was tested in the blowdown-type wind tunnel of Kyushu University to identify the internal flow characteristics corresponding to the flight parameters such as the back pressure, angle of attack and angle of yaw. Flow visualization was achieved by the Schlieren and oil flow visualization techniques. The intake performance was analyzed quantitatively based on the surface pressure and total Pressure measurements. The experimental results were compared with the computational fluid dynamics results. The present study exhibits the fundamental but rarely found experimental results of the high Mach number supersonic air intake.

• Journal of Korean Neurosurgical Society
• /
• v.30 no.6
• /
• pp.749-754
• /
• 2001

Objective : The IDET(Intradiscal electrothermal therapy) appears as a new therapeutic modality for intractable discogenic back pain. We carried out a prospective study to analyze and evaluate the therapeutic effects of IDET. Methods & Results : During a six month period, we performed IDET in 39 patients with chronic low back pain using RITA Model 30 Electrosurgical device. The patients included 21 men and 18 women. The mean patient age was 50.2 years(range 21-73 years). All patients underwent preoperative plain radiography and MRI for excluding non-discogenic back pain. We conducted discography-CT to reveal painful discs in all patients. During the study, we measured intradiscal pressure subjectively. The area of annular tear, which identified with post-discography CT scan, was coagulated in $90^{\circ}C$ of temperature for 15 minutes. Of the 17 patients who were followed up more than three months after surgery, the 10 patients(58.8%) experienced clinical improvement. Three patients had high intradiscal pressure on discography, other three patients had loss of disc height more than 30% of normal on plain radiography, and one patient suffered from postoperative epidural abscess. All of these patients were included in the remaining no improvement group(41.2%). Conclusion : The IDET procedure could be an alternative modality for discogenic back pain. It appears that a patient who has low intradiscal pressure on discography and intact disc height on plain radiography is considered a good candidate for IDET.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.1825-1830
• /
• 2014

Environmental emission of recent automobile is drastically enhanced that it is one of the obvious assignments of exhaust system. This study is a purpose to establish of influence distribution on maxima and minima through the location of pressure on exhaust variable valve. The experiment are checked with real angles using camera which exhaust variable valve is opened side of point. Data has extracted to opening angles with internal flow, pressure. Exhaust variable valve through the floating analysis was analyzed the characteristic of location point about pressure and velocity. The pressures indicated the reduced results internal pressure within muffler. The velocity indicated an opposite results and vibration state of valve was verified to be operated as high speed from lower section. The conclusion to obtain from this study was found out the result to make the optimum back pressure condition as more increasing pressure distribution on valve face if the velocity location attracted by bottom point in order to improve for engine performance.

• Composites Research
• /
• v.27 no.6
• /
• pp.254-259
• /
• 2014

In this study, a device and pressure press process that is able to substitute autoclave process is developed. This process complements disadvantages of autoclave process which are long process-time and high production cost. The developed device provides air pressure as well as the vacuum which are greatest feature of autoclave process. The device is sealed using hydraulic pressure to keep the air pressure inside the mold. The transfer of the heat is designed to be direct. The heating and pressure charging time are decreased by reducing the interior space. Tooling cost is reduced dramatically compared to autoclave process. Spring-back phenomenon is measured and compared. The temperatures of several parts of the mold during molding are measured. The fiber volume fraction of the parts molded by autoclave process and by the developed process are compared.

• Journal of the Ergonomics Society of Korea
• /
• v.31 no.3
• /
• pp.455-461
• /
• 2012

The aim of this study was to investigate the appropriate elasticity of the textile material used for making women's girdle. Background: The elastic textiles have been used for making girdle. The hard type girdle gave high pressure on the body to make slim look. However, excessively high garment pressure caused negative effect to human bodies. This study studied the material giving proper garment pressure in girdle. Method: In this study five experimental girdles were made fabrics with various elasticities. The change of garment pressures and body girths were measured after subjects wearing the experimental girdles. The garment pressure was measured at 10 points. Body girths measured at abdomen, hip, and thigh. Results: The garment pressure of the commercial girdle was high at side of waistband, side femur and back gluteal fold. The experimental girdles made with high elasticity material definitely lowered garment pressure at those points. After wearing experimental girdle their abdomen and hip girths measurements were decreased. But, thigh girth was not reduced. Conclusion: The girdle made with excellent elasticity materials reduced garment pressure significantly and it made body slim as much as the commercial girdle except the thighs. Application: This study provides guideline for the developing girdle that applying optimum range of garment pressure with body slim effect.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.6 no.2
• /
• pp.175-182
• /
• 2002

The cement injection technology on the purpose of ground reinforcement and cut-off has been used in construction sites until now. However, recently it is applied to prevent leakage of underground structure. In this study, applicability of the back side waterproof grouting method was verified through performing field model tests and reviewing case histories. From the results of this study, injection shape of the back side waterproof grouting method was appeared to be root type, and waterproof effect by injection of cement grout material was excellent because grout material infiltrated into boundary between wall of structure and back side ground to be waterproof layer. Components influencing infiltration of injection material are type of soil and degree of compaction. For effective injection, injection pressure has to vary gradually from high pressure to low pessure and small quantity of injection material has to be injected for long times. Also, spacing of injection hole must be designed considering condition of back side ground, injection area, W/C ratio, the number of injection and injection pattern properly.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.29 no.3
• /
• pp.73-84
• /
• 2023

Background: This study aimed to compare pressure pain thresholds (PPTs) in the vertebral segments between patients with chronic lower back pain (CLBP) and healthy participants without back pain and to determine the correlation between vertebral bone-segment PPT and pain level, lower back pain dysfunction, and psychological status in patients with CLBP. Methods: The subjects of this study were 23 healthy adults and 23 adults with CLBP. PPT was measured in 23 spinal bone segments using a PPT device, and the CLBP group was subjected to a pain level test (NRS) and a psychological test using the Korean version of the pain catastrophizing scale (KPCS). The functional level was assessed using the Korean version of the Oswestry disability index (KODI). Results: PPTs of the spinal sclerotomes were significantly lower in patients with CLBP than in healthy participants. In the CLBP group, the composite score of lumbar PPTs showed a high correlation with the composite scores for all segments, but not with the pain level (NRS), KPCS score, and spinal sclerotome PPT. Moreover, PPT in the sacral sclerotomes showed a significant negative correlation coefficient with function, with a KODI score of -.462 (p<.01). Conclusion: In this study, PPTs in all spinal segments in patients with CLBP was significantly lower than that in healthy subjects. The PPTs of the lumbar region was significantly correlated with the PPTs of other spinal regions. Through this study, it was found that there were changes in PPTs in CLBP patients not only in the lumbar region but also in other spinal regions. This information should be considered during clinical treatment of patients with low back pain.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.358-363
• /
• 1987

It is widely noted that pressure feedback systems have been devised to damp the fluid resonance effectively in precision speed control-for large inertia system. A compensation technique preserving the natural output disturbance discrimination characteristics at lower frequencies is proposed The load pressure across positive displacement acceleration. The technique involves feeding back load differential pressure, sensed by pressure transducers, though a simple analog compensatory circuit (high pass filter). The effectiveness of the damping is determined by the filter time donstant and loop gain. Nonlinear total hydraulic simulation results verify the possibility of linear model predictions of extending the closed loop bandwidth beyond the uncompensated frequency.

• Journal of KSNVE
• /
• v.4 no.3
• /
• pp.377-384
• /
• 1994

This paper is an investigation of the performance of absorption diffusers to suppress the vent noise emitted when high pressure gas is throttled. First, experiment for the static performance is carried out. When there is no through-flow, the insertion loss has been obtained in terms of 1/3 octave band spectrum and the effect of the number of diffusers and the thickness of the absorption material on the static performance has been obtained. And the similarity in the spectrum of the static insertion loss is confirmed by comparing two similar models with different size. Second, the dynamic performance has been obtained by experiment using blow-down of compressed air from a storage tank through an orifice of diameter 10 mm. The back pressure by the diffuser is measured and compared with that of a single diffuser. It is found that the insertion loss of asingle diffuser is very low around 3 dB at high frequencies with negative value at low frequencies. By absorption material between the diffuser tubes, however, the performance is increased considerably. Without flow the static insertion loss increases by 3 - 4 dB by doubling the thickness or the density of the absorptionmaterial. With flow, however, the dynamic insertion loss increases. While, the back pressure by the diffuser is small enough to be neglected.

• Journal of Mechanical Science and Technology
• /
• v.20 no.7
• /
• pp.1019-1029
• /
• 2006

The ballistic range has long been employed in a variety of engineering fields such as high-velocity impact engineering, projectile aerodynamics, creation of new materials, etc, since it can create an extremely high-pressure state in very short time. Of many different types of ballistic ranges developed to date, two-stage light gas gun is being employed most extensively. In the present study, a theoretical work has been made to develop a new type of ballistic range which can easily simulate a flying projectile. The present ballistic range consists of high-pressure tube, piston, pump tube, shock tube and launch tube. The effect of adding a shock tube in between the pump tube and launch tube is investigated. This improvement is identified as the reduction in pressures in the high pressure tube and pump tube while maintaining the projectile velocity. Equations of motions of piston and projectile are solved using Runge-Kutta methods. Dependence of projectile velocity on various design factors such as high pressure tube pressure, piston mass, projectile mass, area ratio of pump tube to launch tube and type of driver gas in the pump tube are also analyzed. Effect of various gas combinations is also investigated. Calculations show that projectile velocities of the order 8 km/sec could be achieved with the present ballistic range.