• Composites Research
• /
• 제16권3호
• /
• pp.49-57
• /
• 2003

본 연구에서는 항공기 구조재로 활용되고 있는 카본/에폭시 복합재료와 기체 외부 열차단용 소재로 추천되고 있는 실리카/페놀 및 카본/페놀 복합재료 2종에 대하여 고온 환경하에서 인장시험을 행하였다. 고온용 스트레인게이지를 응용하여 각각의 복합재료에 대한 온도변화에 따른 인장강도, 탄성계수, 프와송비 같은 기계적 물성치를 도출하였으며, 복합재료 방향성에 따른 기계적 물성 및 인장 거동을 강화재 종류별로 비교 고찰하였다. 본 연구결과를 통하여 획득된 기초자료들은 항공기 구조재 및 열차단용 내열재료를 이용한 복합 구조재의 설계 및 해석에 응용되었다.

• 콘크리트학회논문집
• /
• 제24권1호
• /
• pp.53-60
• /
• 2012

이 연구의 목적은 자연모래를 사용한 콘크리트(NSC)와 부순모래를 사용한 콘크리트(CSC)의 고온 하에서의 물리, 역학적인 특성을 조사하는 것이다. 시험체를 $23^{\circ}C$에서 $800^{\circ}C$ 범위에 노출시켜 육안검사와 중량손실을 측정하였으며, 압축강도 시험과 할렬 인장강도 시험을 수행하였다. 그 결과 중량손실률은 노출 온도가 증가할수록 감소하였으며, NSC와 CSC의 감소율은 비슷하였다. 압축강도, 할렬 인장강도와 탄성계수 또한 노출온도가 증가할수록 감소하였다. NSC의 잔존 압축강도는 $200^{\circ}C$와 $400^{\circ}C$에서 CSC보다 급격히 감소했으며, NSC의 잔존 할렬 인장강도 또한 $200^{\circ}C$에서 CSC 보다 급격하게 감소했다. 하지만 CSC와 NSC 공히 $800^{\circ}C$에 노출되었을 때는 비슷한 잔존강도를 나타내었다.

• 펄프종이기술
• /
• 제30권4호
• /
• pp.69-78
• /
• 1998

Papers loaded with 10-40% $TiO_2$ by dry weight were calendered under the various combinations of calendering conditions such as calender type, linear pressure, and roll temperature. After being calendered, light scattering coefficient, surface roughness, density, and tensile strength of the papers were measured and the results were summerized as follows: 1. To increase the light scattering coefficient of $TiO_2$-highly-loaded paper further by calendering, the calender roll pressure and temperature should be kept low. Under these conditions, the physical strength of the paper was not significantly affected. 2. At low roll temperature, soft nip calender and machine calender type showed the same relationship between paper density and its roughness. At high roll temperature, soft nip calender type gave much lower roughness than machine calender type at the same density. 3. At high roll temperature of both calenders, the density as well as the tensile strength of the TiO$_2$-loaded paper was increased significantly.

• 펄프종이기술
• /
• 제32권2호
• /
• pp.16-25
• /
• 2000

The influence of four process parameters of soft nip calendering including calendering pressure, temperature, moisture content and nip residence time on bulk, smoothness and tensile strength of newsprints has been investigated. In addition, the effect of basis weights on calendering responses has been examined. Bulk of newsprints decreased and smoothness increased with the increase of the calendering pressure, temperature, moisture content of the sheets and nip residence time. Improvement in tensile strength was observed when low calendering pressure and high temperature of heat-ing roll were employed. Tensile strength of the newsprint, however, decreased abruptly when the calendering temperature and pressure increased above certain levels due to the rupture of sheet structure, which has been verified by SEM. SEM micrographs also showed that it would be possible to maintain the inner bulk while densifying the fibers on the outer surface of newsprint by adjusting the soft nip calendering variables properly.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.138-141
• /
• 2008

The effects of annealing temperature and time on mechanical properties and microstructures were investigated in cold drawn pearlitic steel wires. During annealing, the increment of the tensile strength at low temperatures found to be due to age hardening, while the decrease in the tensile strength at high temperatures was attributed to age softening, involving the spheroidization of lamellar cementite and recovery of lamellar ferrite. Since tensile strength and the occurrence of the delamination would be closely related to the dissolution of cementite, the lower annealing temperature and the increase of drawing strain caused the higher tensile strength and the easier occurrence of the delamination in cold drawn pearlitic steel wires.

• 열처리공학회지
• /
• 제28권2호
• /
• pp.75-81
• /
• 2015

Effects of B and Cu additions on the microstructure and mechanical properties of high-strength bainitic steels were investigated in this study. Six kinds of high-strength bainitic steels with different B and Cu contents were fabricated by thermo-mechanical control process composed of controlled rolling and accelerated cooling. The microstructures of the steels were analyzed using optical and transmission microscopy, and the tensile and impact tests were conducted on them in order to investigate the correlation of microstructure with mechanical properties. Depending on the addition of B and Cu, various low-temperature transformation products such as GB (granular bainite), DUB (degenerated upper bainite), LB (lower bainite), and LM (lath martensite) were formed in the steels. The addition of B and Cu increased the yield and tensile strengths because of improved hardenability and solid solution strengthening, but decreased the ductility and low-temperature toughness. The steels containing both B and Cu had a very high strength above 1.0 GPa, but showed a worse low-temperature toughness of higher DBTT (ductile-to-brittle transition temperature) and lower absorbed energy. On the other hand, the steels having GB and DUB showed a good combination of tensile and impact properties in terms of strength, ductility, yield ratio, absorbed energy, and DBTT.

• 한국재료학회지
• /
• 제24권10호
• /
• pp.520-525
• /
• 2014

Effects of Cu and B on effective grain size and low-temperature toughness of thermo-mechanically processed high-strength bainitic steels were investigated in this study. The microstructure of the steel specimens was analyzed using optical, scanning, and transmission electron microscopy; their effective grain size was also characterized by electron back-scattered diffraction. To evaluate the strength and low-temperature toughness, tensile and Charpy impact tests were carried out. The specimens were composed of various low-temperature transformation products such as granular bainite (GB), degenerated upper bainite (DUB), lower bainite (LB), and lath marteniste (LM), dependent on the addition of Cu and B. The addition of Cu slightly increased the yield and tensile strength, but substantially deteriorated the low-temperature toughness because of the higher volume fraction of DUB with a large effective grain size. The specimen containing both Cu and B had the highest strength, but showed worse low-temperature toughness of higher ductile-brittle transition temperature (DBTT) and lower absorbed energy because it mostly consisted of LB and LM. In the B-added specimen, on the other hand, it was possible to obtain the best combination of high strength and good low-temperature toughness by decreasing the overall effective grain size via the appropriate formation of different low-temperature transformation products containing GB, DUB, and LB/LM.

• Computers and Concrete
• /
• 제19권2호
• /
• pp.121-126
• /
• 2017

This paper presents the effect of aggregate type on high temperature resistance of self-compacting mortars (SCM) produced with normal and lightweight aggregates like expanded perlite and pumice. Silica fume (SF) and fly ash (FA) were used as mineral additives. Totally 13 different mixtures were designed according to the aggregate rates. Mini slump flow, mini V-funnel and viscometer tests were carried out on the fresh mortar. On the other hand, bulk density, porosity, water absorption and high temperature tests were made on the hardened SCM. After being heated to temperatures of 300, 600 and $900^{\circ}C$, respectively, the tensile strength in bending and compressive strength of mortars determined. As a result of the experiments, the increase in the use of lightweight aggregate increased total water absorption and porosity of mortars. It is observed that, the increment in the usage of lightweight aggregate decreased tensile strength in bending and compressive strengths of mortar specimens exposed to high temperatures but the usage of up to 10% expanded perlite in mortar increased the compressive strength of specimens exposed to $300^{\circ}C$.

• 한국터널지하공간학회 논문집
• /
• 제15권1호
• /
• pp.1-11
• /
• 2013

강섬유 보강콘크리트는 NATM 터널의 숏크리트와 세그먼트 등 라이닝에 주로 적용된다. 터널화재시 라이닝은 화재에 직접적으로 노출되기 때문에 고온노출시 SFRC의 성능변화는 매우 중요하다. 본 연구에서는 고온에 노출된 강섬유보강콘크리트의 인장성능을 DPT 실험을 통하여 검토하였다. 고온 노출온도, 강섬유 혼입률 및 종류가 파괴형태, DPT 인장강도, 실험의 변동계수에 미치는 영향을 분석하였다. 실험결과, 강섬유 보강으로 인한 잔존인장강도의 증가를 확인하였으며, 혼입률이 증가할수록 효과적임을 확인하였다. 그러나, DPT 인장강도는 고온노출로 인한 파괴면의 변화를 고려할 수 없기 때문에 파괴에너지의 고찰이 필요한 것으로 판단된다.

• 대한조선학회논문집
• /
• 제51권3호
• /
• pp.246-253
• /
• 2014

Liquid natural gas is stored and transported inside cargo tank which is made of specially designed cryogenic materials such as 9% Ni steel, Al5083-O alloy and SUS304 and so on. The materials have to keep excellent ductile characteristics under the cryogenic environment, down to -163oC, in order to avoid the catastrophic sudden brittle fracture during the operation condition. High manganese steel is considered to be the promising alternative material that can replace the commonly used materials mentioned above owing to its cost effectiveness. In line with this industrial need, the mechanical properties of the high manganese steel under both room and cryogenic environment were investigated in this study focused on its tensile and fatigue behavior. In terms of the tensile strength, the ultimate tensile strength of the base material of the high manganese steel was comparable to the existing cryogenic materials, but it turned out to be undermatched one when welding is involved in. The fatigue strength of the high manganese steel under room temperature was as good as other cryogenic materials, but under cryogenic environment, slightly less than others though better than Al 5083-O alloy.