• Journal of Sensor Science and Technology
• /
• v.26 no.5
• /
• pp.338-341
• /
• 2017

We have investigated a temperature sensor on a thermal expansion effect of a fused optical fiber coupler. Both side of the fused tapered region of the coupler were fixed on a metal support to induce the high thermal expansion effect. The sensor showed that the peak coupling wavelengths were shifted to shorted wavelength region with increased of environmental temperature. The sensitivity of the sensor was $0.12nm/^{\circ}C$.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.12
• /
• pp.1078-1083
• /
• 2002

The objectives of this paper are to measure the concentration of $H_2$O/LiBr solution by measuring the electrical conductivity and to study the effect of the solution temperature and the concentration on the electrical conductivity of the solution. The solution temperature ranges $20^{\circ},\;40^{\circ},\;and\; 60^{\circ}$ for a fixed concentration during the experiment. The valid ranges of the concentration are two regions, low concentration region (1~20% of LiBr) and high concentration region (55~66% of LiBr). The results show that the conductivity of the solution increases linearly with increasing the solution temperature while it increases without creasing the concentration lower than about 35% of LiBr and decreases with increasing the concentration higher than 35%. This paper proposes experimental correlations for the concentration as functions of the solution temperature and the concentration with error band of $\pm7$% for the low concentration region and $\pm1$% for the high concentration region, respectively. The experimental correlation can be practically used in the on-line measurement without any sampling of solution from the closed system.

• Journal of the Korean Society of Safety
• /
• v.17 no.4
• /
• pp.101-109
• /
• 2002

The electrical properties of polyethylene are changed by the superstructure. Such crystalline polymer as polyethylene or polypropylene changes crystallinity and products spherulite or trans-crystal when it is cooled slowly. In this study, after thermal treatment of LDPE at 100[${circ}C$], in silicone oil for an hour, we made specimens in order of slow cooling, water cooling, quenching according to cooling speed. Also, to study the influence of electrical properties due to the superstructure change, we analyzed physical properties and performed dielectric breakdown experiments using DC and impulse voltage Moreover we measured space charges in bulk using Laser Induced Pressure Pulse(LIPP) method. Trap level of specimen is 0.064[eV] at the low temperature region 0.31[eV] at the high temperature region in DC dielectric strength, 0.03[eV] at the low temperature region 0.0925[eV] at the high temperature region in impulse dielectric strength. As its result shows that the quantity of charges induced from the electrode surface increases with applied voltage time, and the distribution of space charges in samples increases the quantity of charges in proportion to applied voltage.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.3 no.2
• /
• pp.53-60
• /
• 2000

Organic brake materials are installed in the braking system of korean model combat vehicles. Since the binder resin is decomposed in high temperature region, it may possible to drop the friction force which makes the vehicle stop within the desired distance. This study analyses the braking performance of the brake materials in high temperature region by using the pin-on-disk type friction tester. It is observed radical drop of friction coefficients and rapid increase of wear amounts from the transition temperature. It is due to the formation of oxide layer on the friction surface.

• Nuclear Engineering and Technology
• /
• v.55 no.10
• /
• pp.3659-3664
• /
• 2023

The electrochemical behavior of dissolved hydrogen (H₂) was investigated at a Pt electrode in a high temperature LiOH-H₃BO₃ solution. The diffusion current of the H₂ oxidation was proportional to the concentration of the dissolved H₂ as well as the reciprocal of the temperature. In the polarization curve, a potential region in which the oxidation current decreases despite an increase in the applied potential between the H₂ oxidation and the water oxidation regions was observed. This potential region was interpreted as being caused by the formation of a Pt oxide layer. Using the properties of the Cl^- ion that reduces the growth rate of the Pt oxide layer, it was confirmed that there is a correlation between the Cl^- ion concentration and the transient current of the H₂ oxidation.

• Macromolecular Research
• /
• v.11 no.3
• /
• pp.189-193
• /
• 2003

pH- and temperature-sensitive bifunctional hydrogels composed of N-isopropylacrylamide (NiPAAm) and a sulfadimethoxine monomer (SDM) derived from sulfadimethoxine were prepared. These hydrogels exhibit simultaneous pH- and temperature-induced volume-phase transitions. The pH-induced volume-phase transition behavior is produced by the ionization/deionization of SDM and is very sharp. In the high pH region, the ionization of SDM induces swelling of the hydrogels. In the low pH region, the deionization of SDM induces deswelling of the hydrogels. The temperature-induced volume-phase transition behavior of the bifunctional hydrogels exhibits negative thermosensitivity because of the NiPAAm component. The hydrogels swell even at low pH as the temperature decreases. The hydrogels swell at low temperature and high pH, and deswell at high temperature and low pH. The volume of the hydrogels dependl on the balance of the swelling and deswelling produced by the two competing stimuli, pH and temperature.

• 한국연소학회:학술대회논문집
• /
• 1999.10a
• /
• pp.189-200
• /
• 1999

Combustion characteristics of a regenerative combustor for high temperature air combustion have experimentally studied. Temperature measurement on regenerative ceramic material and combustor has been carried out with changing equivalence ratio at constant turn-over period. Stable and unstable combustion region have been found and also detailed averaged temperature profile with respect to various air flow conditions have been obtained.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.3
• /
• pp.105-112
• /
• 2013

The microstructural changes of Fe-20Mn-12Cr-1Cu alloy have been studied during high temperature gas nitriding (HTGN) at the range of $1000^{\circ}C{\sim}1150^{\circ}C$ in an atmosphere of nitrogen gas. The mixed microstructure of austenite and ${\varepsilon}$-martensite of as-received alloy was changed to austenite single phase after HTGN treatment at the nitrogen-permeated surface layer, however the interior region that was not affected nitrogen permeation remained the structure of austenite and ${\varepsilon}$-martensite. With raising the HTGN treatment temperature, the concentration and permeation depth of nitrogen, which is known as the austenite stabilizing element, were increased. Accordingly, the depth of austenite single phase region was increased. The outmost surface of HTGN treated alloy at $1000^{\circ}C$ appeared Cr nitride. And this was in good agreement with the thermodynamically calculated phase diagram. The grain growth was delayed after HTGN treatment temperature ranges of $1000^{\circ}C{\sim}1100^{\circ}C$ due to the grain boundary precipitates. For the HTGN treatment temperature of $1150^{\circ}C$, the fine grain region was shown at the near surface due to the grain boundary precipitates, however, owing to the depletion of grain boundary precipitates, coarse grain was appeared at the depth far from the surface. This depletion may come from the strong affinity between nitrogen and substitutional element of Al and Ti leading the diffusion of these elements from interior to surface. Because of the nitrogen dissolution at the nitrogen-permeated surface layer by HTGN treatment, the surface hardness was increased above 150 Hv compared to the interior region that was consisted with the mixed microstructure of austenite and ${\varepsilon}$-martensite.

• Ocean and Polar Research
• /
• v.30 no.3
• /
• pp.289-301
• /
• 2008

Community structure of heterotrophic protists and their grazing impact on phytoplankton were studied in Northwest Pacific Ocean during October, 2007. The study area was divided into four regions based on physical properties (temperature and salinity) and chlorophyll-a distribution. They were Region I of North Equatorial Currents, Region II of Kuroshio waters, Region III of shelf mixed water, and Region IV of Tsushima warm current from East China Sea. The distribution of chlorophyll-a concentrations and community structure of heterotrophic protists were significantly affected by physical properties of the water column. The lowest concentration of chlorophyll-a was identified in Region I and II, where pico-sized chlorophyll-a was most dominant (>80% of total chlorophyll-a). Biomass of heterotrophic protists was also low in Region I and II. However, Region III was characterized by low salinity and temperature and high chlorophyll-a concentration, with relatively lower pico-sized chlorophyll-a dominance. The Highest biomass of heterotrophic protists appeared in Region III, along with the relatively less important nanoprotists. In Region I, II and IV, heterotrophic dinoflagellates were dominant among the protists, while ciliates were dominant in Region III. Community structure varied with physical(salinity and temperature) and biological (chlorophyll-a) properties. Biomass of heterotrophic protists correlated well with chlorophyll-a concentration in the study area ($r^2=0.66$, p<0.0001). The potential effect of grazing activity on phytoplankton is relatively high in Region I and II. Our result suggest that biomass and size structure of heterotrophic protists might be significantly influenced by phytoplankton size and concentration.

• Transactions of Materials Processing
• /
• v.21 no.3
• /
• pp.207-214
• /
• 2012

High temperature deformation behavior of a $Ni_{30}Fe_{53}Co_{17}$ alloy, with its extraordinary low coefficient of thermal expansion less than $10{\times}10^{-6}K^{-1}$ at temperatures ranging from room temperature to 673K, was investigated by conducting a series of compression tests. From an empirical processing map, the appropriate working temperature-strain rate combination for optimum forming was deduced to be in the ~1373K, $10^{-2}s^{-1}$ region. This region has a relatively high power dissipation efficiency, greater than 0.36. Furthermore, open die forging of a 100mm diameter billets was performed to confirm the variation of thermo-physical properties in relation to microstructure. The coefficient of thermal expansion was found to increase considerably with increasing the open die forging temperature and decreasing the cooling rate, which in turn provides a drastic increase in the average grain size.